FeiYu Tech FY-G3 Ultra Quick Start Manual

3轴无刷云台（适用于Gopro3&Gopro3+)
WARNING!
GoPro Hero 3 or Hero 3+
camera must be installed
before supplying power
to the Gimbal. Failure to
do so will result in
damage to the gimbal
motors.
注意!
请先安装好Gopro3相机后，
再通电。
安装云台减震架
安装云台减震架
安装步骤1：
Step1:
Install the shock mount.
平圆头内六角螺钉 (M2.5×5mm )×4
减震球×6
Hexagonal Socket Head Cap Screw
Damping Ball
前置安装方式示意图
Forward Installation Diagram
Mode Selection Instructions
When connect to RC receiver it can switch in 3 working modes, also
can control the heading and pitch via the RC receiver.
连接遥控接收机，可以切换三个工作模式，还可以遥控俯仰和航向轴动作。
1. Heading Follow Mode：Camera Pitch and Roll angles remain constant,
heading follows the nose position,pitch can be control by RC .
2. Heading And Pitch Follow Mode：Camera Roll angle remains constant.
Heading follow the nose position and Pitch follow the elevation of the
aircreft.
3. Heading Lock Mode: Heading, Pitch and Roll are all locked to point at
one position.Heading and pitch can be control by RC .
1. 航向跟随模式：俯仰和横滚锁定，航向随着机头的方向平滑的转动，俯仰可通
过遥控器控制。
2. 航向和俯仰跟随模式：横滚锁定，航向随着机头的方向平滑的转动，俯仰随着
飞机仰角的转动。
3. 锁定模式：航向、俯仰和横滚都锁定，航向和俯仰可以通过遥控器控制。
Indicator:
LED Status
Single Flashes
Double Flashes
On Constantly
电机指示灯：
指示灯状态
单次闪烁
双次闪烁
常亮
Introduction 介绍
FY-G3 Ultra 3 Axis Brushless Gimbal( for aircraft ) Suitable for GoPro3,GoPro3+ or camera with similar size.Can be easily mounted in fixed
wing, multirotor, helicopter for aerial photography, and can work independently only need power supply.
You can assemble the gimbal properly according to the drawing, and then install the video camera on it. The camera mount currently is
only suitable for GOPRO3, for other kinds of cameras, you can design the mount by yourself or concern Feiyu Technology,and we will
release more camera mount accessories in the near future.
There is no need to set up and adjust the parameter. For the first use, power on the Gimbal, and then keep it static for a while, after its
reset, the gimbal will be in a level position automatically. Then you can use it normally.
Firmware Upgrade:
The Gimbal supports firmware upgrade: You can download the upgrade software and the latest firmware from www.feiyu-tech.com
FY-G3Ultrl 飞行器版本（For Aircraft） 三轴无刷云台， 适用于GOPRO3,GOPRO3+或其它尺寸相近的摄像机。可以安装到固定翼飞机，多轴飞
行器，直升机上航拍。安装简单方便，只需连接电源便可以独立工作。
按照图纸正确的组装云台，先不要通电，把摄像机安装到云台上.目前的相机安装座只适合安装GOPRO3&GOPRO3+摄像机，其它摄像机可以自
行设计安装座或者关注飞宇科技发布的相机安装座配件。
无需要设置和调整参数。首次使用，接通云台电源，保持云台静止，等待云台初始化完成后自动将云台回到水平位置，然后可以正常使用了。
固件升级：
可以在网站www.feiyu-tech.com下载云台的升级软件和最新控制固件。
安装步骤2：
Step2:
平圆头内六角螺钉 (M2×4mm)×2
Hexagonal Socket Head Cap Screw
功能介绍
Function Explanation
Heading follow mode
Heading and pitch follow mode
Heading,pitch and roll are all locked
功能说明
航向跟随模式
航向和俯仰跟随模式
锁定模式（航向、俯仰和横滚都锁定）
固定3轴云台在减震架上
Fixed the 3 axis Gimbal on the shock mount
悬挂安装方式示意图
Inverted Installation Diagram
安装相机
安装步骤3：
Step3:
Install the camera
滚花手拧螺钉（M2×22）×2
M2×22 Knurled Thumb Screw
电源连接线路图 Power Supply Connection Diagram
云台连接线路图
Gimbal Connection Diagram
航向控制
Heading Control
棕 Brown
俯仰控制
Pitch Control
模式切换
Mode Switch
电源:9.0~17.0V
Power Voltage：
9.0~17.0V
RC Receiver
RC 接收机