FeiYu Tech FY-G4 GS Manual

For SONY Sports Video Camera
Gimbal For Sony
Sports Video Camera
Suitable for SONY FDR-X1000V and AS series sports cameras
1
Beginner Guide
Attention ! Please install the suitable camera first before power on the Gimbal.
Insert The Batteries
Remove the power
switch cap, insert two
18350 batteries into
the handle.
Power On
Confirm the camera
is installed well, then
press the power
button to turn on
the Gimbal.
2
Product Appearance Instructions
Pitch Axis Roll Axis
Heading Axis
Function
Button
Function
Interface
Power
Switch
If any comments or suggestions please do not hesitate
to e-mail us directly : service@feiyu-tech.com
3
EN
FEIYU-EN-1
The working mode and function
can be identified by the LED status
Install The Camera
Special Working Condition (Inversion Mode)
Gimbal will enter into the inversion mode and switch to the Heading following mode automatically. Invert the Gimbal to capture more excited
Install the sports camera by the
scenes easily by switching mode combination. When in inversion working condition press the function button for three times in succession to reset
special Thumb Screw. And make
the Gimbal back to the original state.
sure it is fixed well.
Standby Mode
This indicates that the Gimbal is in the standby mode. Single press the function button the Gimbal will be awakened immediately.
Manual Pulling Locking
Lock Mode the pitching can be adjusted to the desired angle manually, wait in this position up to 0.5 second until the current angle is adjusted.
Operation
Single Press
Mode Switching
Double Press
When the Gimbal is working,
Three Press
you can press the function
Long Press
button to switch among the
For 1 Second
three working modes and a
special working condition.
Smooth And Steady Filming: Handheld the Gimbal, keep stable for movement, keep light and steady for walking.
( Details of working modes please How To Adjust The Pitching Angle: Double press the function button to enter into"Heading And Pitch Follow Mode".
Hold the Gimbal at the desired angle, then press the button once to reengage "Heading Follow Mode" in order to lock the
refer to the instructions of
angle of desired pitch.
working modes )
Selfie: Turn the Gimbal 180°so the function interface is facing you. Then, simply adjust the angle of pitch to the desired
angle by utilizing the "Heading And Pitch Follow Mode"which described above and then switch back to "Heading
Follow Mode". Once complete you can film yourself with ease.
4

Standard And Optional Accessories

Standard Accessories
Indicator
Indicator Explanation
LED Status Explain
Blue light flashes
Full Power
three times
Blue light flashes
Enough Power
twice
Blue light flashes
Low Power
once
Blue light keeps
No Power
flashing
The indicator flashes in red light
when in working, it will prompt the
Gimbal at fault.

Operation Instructions

Function Button Working Mode Instructions
Use for switch
Heading Follow Mode
the working
constant, heading follows the handheld position.
mode and
Heading And Pitch Follow Mode
realize other
function
constant. Heading and Pitch follow the handheld position.
Lock Mode
Heading, Pitch and Roll are all locked to point at
one position.
When in any working mode, press the function button for three times in succession, the
Press the function button for 3 seconds, then the motor will stop working and the LED of the function button will light constantly.
The pitching can be adjusted 8 seconds after the Gimbal has been started. Within the Heading Follow and Heading

Function Button Instructions

LED Status Function Explanation
Single Flashes Heading Follow Mode
Double Flashes Heading And Pitch Follow Mode
Single Flashes Inversion Mode
On Constantly Lock Mode
Charger Rechargeable
Battery
Input: DC 5V
Type: 18350
Output: DC 4.2V
USB
USB Connector
Mini-USB
USB Cable
Camera Pitch and Roll Angles remain
Camera Roll Angle remains
Operation Again
Function Of Operation Again
Other operation is arbitrary
Other operation is arbitrary
Three Press again Exit inversion mode to original state
Other operation is arbitrary
Correct Method For Using USB Data Cable
Please refer to the method of proper usage
!
mentioned below. Otherwise the device
itself or other equipments can be damaged
Battery Charging: Put the Mini-USB terminal of the USB
cable into the Mini-USB interface of the charger and the
USB terminal to the power adapter, optional connect to
the EU Connector.
Connect The Computer: Please remove the batteries first,
then insert the Mini-USB terminal into the function interface on the
Gimbal and the USB terminal to the USB connector. Afterwards
connect the device with the computer to do firmware updates or
parameter configuration. (Please connect the USB cable to the
computer with the USB connector, otherwise the interface of
the computer will be damaged ).
Further information can be found in the chapter of the
Function Interface Instructions.
Optional Accessories
Name Function Description
Realize the heading & pitch angle adjustment,
Remote
mode switching, level calibration and heading
Control
follow speed configuration from a distance.
Extend the capacity space for battery to
Battery
Extender
make the runtime longer.
Spiral design of the extension bar can be
perfect combination with G4 power switch；
Extension
Bar Extended length is optional, it will help to
enjoy a different visual easily.
Heading