FeiYu Tech FY WGS Manual

Introduction
1
FY WGS is a lightweight, yet feature-rich, wearable 3 axis gimbal capable of capturing immersive and fully stabilized footages. It is compatible with
GoPro HERO4 Session and other cameras with the same dimensions.
The FY WGS is a miniaturized version of the best-selling FeiYu gimbal, offering exceptional stabilization technology in a wearable form factor for
action cameras. A GoPro T-Clamp adapter is packaged with every FY WGS. Users can attach the gimbal to any accessories supporting the GoPro
three-prong mount. The FY WGS also contains two 1/4" tripod mounts on its gimbal body, allowing the gimbal to be mounted in different orientations
to all universal tripod screw mount accessories (including helmets, bikes, selfie sticks and other accessories).
Install
2
Camera In Right
Camera in Left
Operation
3
Function Function
Switch between different operating modes by pressing the function button.
Button Button
The LED light will flash distinctively to indicate different operating modes.
Operating Modes and Functions Operating Modes and Functions
Mode #1 - Panning Mode
Camera is permitted to pan left or right. Vertical tilts or rolls are restricted.
Mode #2 - Panning and Tilting Mode
Camera stays in its current orientation. All panning, tilting and rolls are restricted.
Mode #3 - Lock Mode
Inversion Mode Pressing the function button three consecutive times in any operating mode, the gimbal will switch to the
Inverted Mode (Allowing the user to flip the gimbal orientation upside down). Pressing the function button three more times
while in Inverted Mode to switch back to the original orientation.
Manual Pulling Locking
After the gimbal has been powered on for eight seconds, the tilt angle can be adjusted manually in the Panning
Mode and the Lock Mode. Adjust the title angle to the desired position and wait for 0.5 second until the gimbal registers the new angle.
Reset Pressing the function button four consecutive times will reset the gimbal to initial orientation.
By using the optional FY remote control, tilt and level can be adjusted without connection to a computer.
Tilt and Level Calibration
For more information, please refer to FY remote control section in the instruction manual.
Operation LED Status
Single Tap LED Flashes Once
Double Tap LED Flashes Twice
Triple Tap LED Flashes Once
Quadruple Tap LED Flashes Once
* When the gimbal is in the Inverted Mode it will revert back to the original orientation after three press.
When the battery is low, the gimbal will make three beeping sound and automatically shut down itself.
Accessories
4
Rechargeable Battery
Charger
Input: DC 5V Min 800mA
Output: DC 4.2V
USB Connector
FY WGS 3 Axis Wearable Gimbal is compatible with Gopro HERO4 Session
STEP 1
Remove the screws on the
battery compartment,
insert two16340 batteries
and tighten the screws.
!
WARNING ! WARNING !
Do not power on the Do not power on the
gimbal before completing gimbal before completing
all the installation steps. all the installation steps.
STEP 2 STEP 3
Mount the camera carefully 1
to the mounting bracket 2
and tighten the screws.
3
Power on: Ensure the camera is mounted securely, then hold down the function
POWERING
button for 2 seconds to turn on the gimbal.
ON / OFF
Power off: Hold down the function button for 3 seconds to turn off the gimbal.
Vertical
Camera In Right
Camera is permitted to pan left or right and tilt up and down. Rolls are restricted.
Function Button Quick Reference
Function Explanation
Panning Mode
Panning and Tilting Mode
Inversion Mode
Reset
M 1.5 Allen Key
Type: 16340
USB Cable
3
Accessories For
1/4 Inch Screws
Long screw
2
T-Clamp
Hexagonal Socket
Head Cap Screw
Please choose one way:
Use the 3M Adhesive to fix the bottom of the Gimbal.
Use GoPro Accessories, mount the provided T-clamp to the side
or the bottom of the gimbal. Attach T-clamp to any accessories
supporting the standard GoPro three-prong mount.
The gimbal can also be mounted directly to other accessories
using the standard 1/4" tripod mount. Tighten all screws and
ensure it is firmly mounted before using the gimbal.
Forward
Camera in Left
Camera In Right
Tilting
Function
Button
Operation LED Status
Long Press
On Constantly
For 1 Second
Long Press Turn On And Switch To
The Mode's LED Status
For 2 Second
Long Press Turn Off After
A moment
For 3 Second
HexagonalSocket
HeadCap Screw
T-Clamp
M2 * 6mm
Curved Adhesive Quick-Release
Mounts Buckle
Tilting Axis
1
3M
Adhesive
Function Button
（ ON / OFF ）
Inverted
Camera in Left
Rolling
Panning
Function
Lock Mode
Power On
Shutdown
How to Charging
Long screw
3M Adhesive
Manual Version 1.0
Rolling Axis
Function
Interface
Panning Axis
Screws For
The Battery
Compartment
T-Clamp
Screw Hole
T-Clamp
Screw Hole
1/4 Inch
Screw Hole
T-Clamp
Screw Hole
1/4 Inch
Screw Hole
USB Cable
5V USB Power
Adapter
（Not Included）