Right hand and left hand are determined by facing the direction of forward travel respectively. HORSCH reserves the right to alter illustrations as well as technical data and weights contained in this manual at any time without notice.
Warranty Guidelines 1. The period of warranty for material defects relating to HORSCH products will be 12 months. In the case of written deviations from the statutory provisions, these agreements shall apply. They shall become effective upon delivery of the machine to the end customer, unless the unit is stored during seasonal months, whereas the machine is not utilized.
I hereby confirm receipt of the Owner’s Manual and Parts Catalog for the above-mentioned machine. I have been instructed and informed by a HORSCH factory trained Service Technician / authorized Dealer representative in the operation and functions of the machine, as well as in the safety requirements.
I hereby confirm receipt of the Owner’s Manual and Parts Catalog for the above-mentioned machine. I have been instructed and informed by a HORSCH factory trained Service Technician / authorized Dealer representative in the operation and functions of the machine, as well as in the safety requirements.
I hereby confirm receipt of the Owner’s Manual and Parts Catalog for the above-mentioned machine. I have been instructed and informed by a HORSCH factory trained Service Technician / authorized Dealer representative in the operation and functions of the machine, as well as in the safety requirements.
To the best of my knowledge, this machine has been delivered ready for field use and the customer has been fully informed as to proper operation and care. Signed: ................. (Customer) Signed: ................. (Dealer Representative) Date: ..................www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Model number of the machine, can be found on the Serial Number Tag. HORSCH, LLC has placed a Serial Number Tag (reference picture below) on the machine with the above- mentioned information. It is located on the main frame cross member tube directly behind the front hitch, just off center towards the left-hand side of each machine.
Ensure that the operator has read and understood the operating instructions. • The operating instructions are a key component of the machine. Do not carry out any operations which may affect the safe use of the machine. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Machine Installation to Service Instruction of the operation and initial installation of the machine are done by an authorized dealer or HORSCH representative. The machine can be released for operation only after instruction by our service technician or authorized distributor has been completed and the operating instructions have been read and understood.
Information Regarding Safety The following warnings and safety instructions apply to all sections in these operating instructions. Safety Symbols on the Machine: www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Use a Signal Person The machine must only be put into operation after receiving instructions by employees of the authorized dealer or a HORSCH employee. The machine registration form has to be completed and returned to HORSCH. In addition to the operating instructions, it is...
DO NOT EXCEED A MAXIMUM SPEED OF 20 MPH DURING TRANSPORTATION. LOSS OF VEHICLE/MACHINE CONTROL CAN RESULT IN SERIOUS PERSONAL INJURY OR DEATH! ONLY TRANSPORT WITH EMPTY SEED AND FERTILIZER TANKS! www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
(tines, discs)! • Do not use the packer or other rotating parts when climbing onto the machine. These could start to rotate, and you could fall and be seriously injured. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Attach to a tie down approximately 3 months to cure location or the main frame. Do and could thus be damaged if not pull the machine sideways. this time has not yet expired. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Waste oils must be collected and disposed of with local regulations. Never pour used oil in to a sewage system or drains or on to the ground. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
150 Ft. / Lbs. *The use of proper torque-type tools/equipment is essential for correct and adequate torqueing of specified items. See a list below for recommended torque tools. Obey all posted torque specifications. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
The Case Drain MUST be connected prior to below. machine operation! The case drain must be used especially during machine wing fold/unfold operation, to avoid hydraulic system back pressure, that may cause damage to other components! www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Do not wash new machines with steam-jet high- pressure cleaner. The paint takes approximately 3 months to cure and could thus be damaged if this time has not yet expired. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
• Check the area around the machine (for Instruction of the operation and initial installation children!) before setting off and starting of the machine will be carried out by HORSCH operation of the machine. Ensure sufficient service representatives or distributors.
MAY/CAN RESULT menu ‘Machine Data’ using the menu option PROPERTY DAMAGE ‘hydraulic bout marker control’ (See E-Manager SERIOUS PERSONAL INJURY instructions). OR DEATH! www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
6. Lift the machine. Check the road lighting equipment at regular intervals to prevent any other road users from Do not transport the machine in being endangered by negligence! position higher than necessary. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Extra Power Harness Connector good working order. 1. Connect the 7-pin plug of the planter lighting equipment to the tractor. 2. Check lighting equipment and warning decals for function and cleanliness. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
- Distance from middle of tractor link arm ball to center of gravity of rear implement (rear ballast) x - Information of tractor manufacturer for min. rear ballasting. If no information is available, enter 0.45. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
3. Follow procedures above for proper extra precaution is taken, but is not parking of the machine. recommended! 4. Follow procedures above for proper unhitching of the machine. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Fold/Unfold procedures may vary based on operating the hydraulic system. monitor used, i.e.. Standard HORSCH Always keep an eye on the machine during the Terminal vs. Touch 800/1200, etc., and folding process. version software installed. Folding movements must only be performed on Once the conditions for the next work step are firm and level ground.
30° when gauge wheels resume its folding function. begin to slide out. Once the gauge wheels have slid into outward position on the tool bar the X’s will switch to green check marks. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Page 63
‘OK’ button will change to black or a check mark will appear. 14. Press the ‘OK’ button to exit the fold menu and navigate back to the main work screen. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
NOTE: Activate slide function before continuing with the unfold procedure! Do NOT attempt to slide the gauge wheels in/out with the wheels contacting ground damage will occur! www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Maintenance Clean any dirt or deposits from the fan • blades prevent unbalance damage to impeller and tapered bushing. Check hoses and connections every day. • www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
While tightening, you can lightly tap on the flange with a plastic hammer to keep it aligned. Torque to 5 ft./lbs. • www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Air leaks lead to planting and metering errors. The seed tank will be pressurized when the fan is on. An air vent is located on the top of the seed www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
For emptying, place a container under the distributor and pull the gate valve out slightly. Gate Valve SOD Distributor (Open) Remember to close the SOD distributor and return the gate valve to it storage position. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
These parts would become brittle the star knob. Tighten both star knobs only hand and break. tight! www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Maintenance / Inspection Check the metering unit every day for signs of damage clean with brushes compressed air. Do not use water. Metering Unit www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Size of Holes / Slots • The selection of disks is continually adapting and changing. Before you start planting, you should ask your HORSCH representative for further assistance with metering disks. If the metering disks are to be changed out and used again at...
Maestro Disk Kit Contents NOTE: Kit types and components of kits vary and may be subject to change without notice. Contact your nearest authorized HORSCH dealer representative for current kit information. See model year specific parts catalog for further detailed information.
Note 3: If seed can fit through the slot/hole in the disk or extend through the slot/hole in the disk far enough to cause jamming of the meter, then always use a disk with a smaller slot/hole. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
For canola, HORSCH offers a shaker box and multiple sieves for assisting in determining the correct size seed and seed discs. For further information contact your local authorized HORSCH representative or see the model specific Parts Catalog for illustration and part information.
As a rule of thumb, the required vacuum level will be higher when using slot type discs compared to that of hole type discs. The effect of this vacuum adjustment only becomes apparent by testing. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Seed Extractor The extractor is available in two versions, A and When assembled, these can be identified by the top corner of the extractor. (See below) Seed extractor A & B www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
2. Adjustment lever for Outside Scraper For information related to proper identification of 3. Inside Scraper scrapers see the following page. 4. Fill level plate Meter Housing for Soybeans Meter Housing – Except Soybean www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
1. In case of skips adjust towards 9. The correct outside scraper must be installed for the desired crop. Type of Seed Outside Scraper Number of Notches Corn Sunflower Sugar Beet Sorghum Cotton Canola Soybean Wheat www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
“C” already installed in the meter housing. The scraper must be free to move, and it should rest against the metering disk. This checked through the opening in the air intake dust screen. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Metering disks should be selected by using the guides below. Selection of the correct seed disk depends on seed type, shape and planting population. In overlapping areas, test the disk with the smaller holes/slots first. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
After the test run, transfer the After the test check the seed setting to all row units and for damage. adjust. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Any changes to the metering unit can influence the seed placement accuracy. Pay attention to the test results and the display on the terminal. Repeat the test sequences in case of negative results. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
The seed tube must not be damaged or dirty. Dust deposits in the sensor window can adversely affect the signals on the sensor. This can be the reason for incorrect data (faults) in the computer. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
• Check the gasket at the top of the seed tube inlet. The connection must be leak tight so that no foreign particles can fall in causing incorrect seed signals. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Remove the firming wheels so the machine can When new, the gap is approx. 3mm wide. rest on the opening disks. Opener Disk Gap 1. Frame 2. Opening Disk 3. Gauge Wheel Firming Wheel in Parked Position www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
To replace or adjust the discs see HINT: The disc blade bolts are left and the following illustrations and instructions. right hand threaded, respective to left- www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Do not work under a lift, inadequately secured machine. Always wear adequate protective equipment for all repair and maintenance work. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Adjust as required. Check the wheels daily for damage and • • Lubricate both grease zerks of the gauge free rotation. wheel arms once weekly. Check the depth setting placement daily. • www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Protect the machine against rust. Only • abrasive and can cause corrosion. spray with biologically degradable oils, i.e. rapeseed oil. Clean out the seed tank, fertilizer tank • and SOD manifolds thoroughly. www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
The machine should be lubricated regularly and after every pressure wash. HORSCH, LLC hopes you are completely This ensures operational reliability and reduces satisfied with your machine and the HORSCH the costs of repair work and down time. company itself. See Maintenance Schedule of the following page.
Check state, wear, bearing clearance and free rotation Gauge wheels Check spacing with opening disks Drill unit Firming wheel Check for damage and free rotation Set the depth setting to the depth of the opening disks www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Clean the machine Do not spray plastic parts with oil HYD Cylinder Piston rods Spray with anti-corrosion oil After 3 - 5 years Hyd hoses for lifting and folding cylinders Replace www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Calibrate system (see instructions) distribution Incorrect orifice size Use correct orifice size for fertilizer rate and planting speed. Plugged hose Check all hoses. Leak in system Find and fix the leak www.horsch.com Maestro RC Owner’s Manual – Ver. 2.1 10/2019...
Need help?
Do you have a question about the Maestro RC Central Fill 1230 and is the answer not in the manual?
Questions and answers