Table of Contents
Advertisement
Chapter 5
Maintaining the Cisco 6400
Figure 5-10 Inserting an NSP into the Chassis
management
Blower
module
PEM
PEM
To ensure that the NSP module mates properly with all backplane connector pins, the card length and
Caution
card slots have been designed with very close tolerances. To slide the module into the slot requires
gentle pressure with each hand, at the top and bottom of the faceplate.
Gently slide the module into the slot until it makes contact with the backplane.
Step 4
Press the upper lever down and the lower lever up at the same time.
Step 5
Secure the card by tightening the upper and lower retaining screws.
Step 6
Connect the cables.
Step 7
Pull the cables across the wire restraint and bend the restraint upward to trap the cables
Step 8
OL-2133-02
Slot 1
Slot 3
Slot 2
Cable
bracket
FANS
FAN
OK
FAILUR E
1
2
3
NRP
NRP
OC-3
STM-1
FAIL
PORT 0
TX
RX
STATUS
PORT 1
TX
RX
STATUS
NSP
CON
POWER
FAULT
AUX
MISWIRE
CON
CON
ACT
AUX
AUX
ETH
LNK
PCMC IA
OC-3
STM-1
FAIL
PORT 0
TX
RX
STATUS
PORT 1
TX
RX
STATUS
STATU S
STATU S
Slot 1
Slot 0
FAIL
POWE R
FAIL
FAULT
ACO
MISWI RE
CRITI CAL
MAJO R
MINO R
ALAR MS
STATU S
Slot 5
Slot 7
Slot 0A
Slot 6
Slot 4
Slot 0B
Slot 8
MULTI-
FAN
FAILUR E
CAUTIO N
When hot swapping this
fan tray,
removal and replacem ent
must
be done in under two minutes
or
system shutdow n will occur.
4
0A
PRO CES SOR ONLY 0B
5
6
7
OC-3
NSP
STM-1
NSP
OC-3
OC-3
OC-3
FAIL
STM-1
STM-1
STM-1
FAIL
FAIL
FAIL
PORT 0
CON
CON
TX
RX
PORT 0
STATUS
PORT 0
PORT 0
TX
RX
TX
RX
STATUS
TX
RX
AUX
STATUS
PORT 1
AUX
STATUS
TX
RX
PORT 1
PORT 1
STATUS
PORT 1
TX
RX
ACT
TX
RX
TX
RX
ACT
STATUS
STATUS
ETH
STATUS
ETH
LNK
LNK
PCMC IA
PCMC IA
OC-3
STM-1
OC-3
OC-3
Slot 1
STM-1
OC-3
FAIL
STM-1
Slot 1
STM-1
Slot 0
FAIL
Slot 0
FAIL
FAIL
PORT 0
TX
RX
PORT 0
ACO
PORT 0
STATUS
PORT 0
ACO
TX
RX
TX
RX
TX
STATUS
RX
CRITI CAL
STATUS
STATUS
PORT 1
CRITI CAL
MAJO R
TX
RX
MAJO R
PORT 1
PORT 1
STATUS
MINO R
PORT 1
TX
RX
MINO R
TX
RX
TX
STATUS
RX
STATUS
ALAR MS
STATUS
ALAR MS
STATU S
STATU S
FAIL
FAIL
PRO CES SOR ONLY
Cisco 6400 Hardware Installation and Maintenance Guide
Replacing an NSP Module
8
NRP
SUB
SLOT
0
CON
AUX
SUB
SLOT
1
STATU S
FAIL
(Figure
5-11).
5-13
Advertisement
Table of Contents
