Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Discount Car Stereo JAGCD-HF
Summary of Contents for Discount Car Stereo JAGCD-HF
- Page 1 Courtesy of: DiscountCarStereo.com Serving the internet community since 1995 JAGCD-HF Quick Start Bluetooth Installation Guide for select Jaguar xJ & xK with CD Changer Works in 1998-03 x308 and 1997-06 x100 Created May 15, 2016 Revised: January 11, 2020...
- Page 2 Safety comes first when you’re on the road, so having an intuitive and easy to Once disconnected; CD changer female connector (right), use Bluetooth kit is essential to reducing driver distraction. The JAGCD-HF amplifier/radio plug (left) see Fig. 2 Bluetooth receiver is compatible with virtually all smartphones, and sounds great for mobile conversations or streaming music.
- Page 3 Connect factory male (See Fig. 2) audio module female (See Fig. 3a) Route 6-pin plug (See Fig. 4) on audio cable to center console area. Routing Audio cable (sedan) Fig. 8 Use a pry tool to open gap between window pillar and rear deck as Fig.
- Page 4 Installing Bluetooth Module Bluetooth Module Red wire requires 12V Accessory supply (Do not connect to constant battery supply) and Black wire must be grounded. In our t 2001 XJR Premium Audio test vehicle, Bluetooth module was Factory connector/Plug Accesory wire Ground wire secured to center armrest sidewall (See Fig.
- Page 5 2. Connect 6-pin audio splitter plug (See Fig. 13) to audio cable 6-pin connector (routed from trunk/hatch) Fig. 15 pigtail jack 5. Connect microphone/push-button (See Fig. 16) to Module mic input jack (See Fig. 14) Fig. 13 Audio splitter 3. Connect audio splitter straight 3.5mm plug (See Fig. 13) to Module input jack labeled (CD) (See Fig.
-
Page 6: Usb Charging Port
USB CHARGING PORT The USB port is for charging only. Should you decide to use it, we suggest one of 3 connecting options: A. Flush to dash/panel (requires drilling a ¾” hole) B. Flush Mount with Support bracket (use this option to mount USB wherever your installation demands without drilling) C. - Page 7 Locate a flat surface at location of choice within 3.2 ft. (1 meter) of module and mount USB support bracket (See Fig. 24) to surface using adhesive/tape or screws. Fig. 21 Module USB port Push USB header (See Fig. 22) until it snaps in place and flush with mounting surface (See Fig.
-
Page 8: Bluetooth Pairing And Connection
Select the G2 and tap “Connect” Fig. 27 Radio must be in “CD Mode” when using the JAGCD-HF. CD changer remains connected and operational. Note: Pairs up to 4 phones but connects to one phone at a time. -
Page 9: Phone Commands
CD Changer Operation From control button the following phone commands are possible. The JAGCD-HF unlike our JAG-HF and BT45-JAG retains CD changer functionality. To operate, press “CD” button on radio, then press control button 4 times. To Proceed this way exit CD changer mode press control button once. -
Page 10: Package Contents
Optional visor microphone Kit The default button has a built-in microphone (See Fig. 28) Fig. 30 Fig. 28 Installation: which means mounting the button in certain areas may be great for controls, but may not so great for issuing voice commands or holding Bluetooth Use clip to secure microphone to visor or location of choice and route conversations. -
Page 11: Frequent Asked Questions
The likely cause is the microphone and control buttons connections are reversed. You may also use the blue push button with the visor kit. 3. In which model/year Jaguars will the JAGCD-HF work and where does the audio adapter connect? 1998-99 x308 (To Changer/Trunk) - Page 12 Email support@discountcarstereo.com © 1995-Jan-20 Discount Car Stereo, Inc. All rights reserved. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders.