Excess Flow Safety Valve Reset Procedure; Care And Maintenance - Broil King 06695008 Operator's Manual

Flare-ups
"Flare-ups" sometimes occur when food drippings fall onto the hot heat distribution plate or burners and ignite. Some flaring is
normal and desirable as it helps impart the unique flavors associated with grilled foods. Controlling the intensity of the flare-ups is
necessary, however, in order to avoid burned or unevenly cooked foods and to prevent the possibility of accidental fire.
WARNING:
Always monitor the grill closely when cooking and turn the flame level down to LOW or OFF if flare-ups intensify.
Shutting Off Burners
1. Always turn the valve knob(s) clockwise to the ''HIGH'' position, and then press and turn it to ''OFF''. Never force the knob
without pressing it. This could damage the valve.
2. Promptly turn the gas supply to the "OFF" position on the natural gas valve.
3. Close the lid of the grill.

Excess flow safety valve reset procedure

●
The new regulators are equipped with a safety device that restricts the gas flow in the event of a gas leak. However,
unsafe practices of grill operation could activate the safety device without having a gas leak.
●
A sudden shut off of the gas flow typically occurs if you open the natural gas valve rapidly, or if one or more of the burner
control knobs is in an open position when opening the natural gas valve.
● This procedure effective with Natural Gas.
● To ensure the procedure is safely and successfully performed, please carefully follow these instructions:
1. Close the natural gas valve.
2. Turn all burner control knobs to the OFF position.
3. Disconnect the natural gas hose from the natural gas inlet.
4. Open the lid of the grill.
5. Turn burner control knobs to HIGH.
6. Wait at least 1 minute.
7. Turn burner control knobs OFF.
8. Wait for at least 5 minutes.
9. Re-connect the natural gas hose to the natural gas supply.
10. Slowly turn the natural gas valve ¼ turn at a time and have the valve all the way open.
11. With the lid open: For grill with ignition button: turn on only ONE burner control knob to the HIGH position. Ignite
the grill by pushing the ignition button. For grill with an automatic ignition: Push down the control knob you want to
light, turn counter clockwise until you hear the ignition click.
12. After the first front burner is lit, turn on the other control knob(s) to the HIGH position. If you have more than two
burners, turn them on only ONE AT A TIME.
13. When all front burners are lit, close the grill lid.
14. Wait for 10-15 minutes; the temperature should reach 400 – 450°F
IMPORTANT
Always allow to completely cool off before covering your grill to prevent corrosion from condensation.
CAUTION:
All cleaning and maintenance should be done when the grill is cool, with the fuel supply turned off at the control dial and the
natural gas valve disconnected. DO NOT clean any grill part in a self-cleaning oven. The extreme heat will damage the finish.
Cleaning
Burning off the grill after every use (approx. 15 minutes) will keep excessive food residue from building up. Clean the grill
before and after cooking is recommended.
Recommended cleaning materials:
Mild dishwashing liquid detergent
Nylon cleaning pad
Paper clip
Compressed air
DO NOT use cleaners that contain acid, mineral spirits or xylene.
Outside surfaces
Use a mild dishwashing detergent and hot water solution to clean. Rinse thoroughly with water.
Inside surface
If the inside surface of the grill lid has the appearance of peeling paint, baked on grease has turned to carbon and is flaking off.
Clean thoroughly with a strong solution of detergent and hot water. Rinse with water and allow it to completely dry.
Interior of grill bottom – Remove residue using brush, scraper and/or cleaning pad. Wash with a dishwashing detergent and
hot water solution. Rinse with water and let dry.
Cooking Grates – The porcelain grates have a glass-like composition that should be handled with care. Use a mild
dishwashing detergent or baking soda and hot water solution. Non-abrasive scouring powder can be used on stubborn stains.
Rinse with water.
Heat Plates – Clean residue with wire brush and wash with soapy water. Rinse with water.
Grease Cup – Periodically empty the grease cup and clean with a dishwashing detergent and hot water solution.
GSF2818KSN
Instruction Manual
Guide d'utilisation

Care and Maintenance

Hot water
Wire brush
Putty knife/scraper
15
.