Advertisement
Table of Contents
Control Commands
Model #: HDM-SWITCHPRO-VW4
© 2012 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. ("Avenview") products. Avenview makes no representations or warranties
with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product
descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this
publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims any express
or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or
infringement of any intellectual property right. Reproduction of this manual, or parts thereof, in any form, without the express written permission of
Avenview Inc. is strictly prohibited.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Avenview HDM-SWITCHPRO-VW4
Summary of Contents for Avenview HDM-SWITCHPRO-VW4
- Page 1 No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
- Page 2 TABLE OF CONTENTS SECTION 1: COMMAND PROTOCOL FORMAT (RS-232 SERIAL PORT) ........3 TECHNICAL SUPPORT ........................10 www.avenview.com|2...
- Page 3 CONTROL: Connect to an active network line for LAN serving and Telnet/Web GUI control. c. IR OUT/IN: Reserved. d. SERVICE: This port is reserved for firmware update only. e. OUTPUT 0: Connect to DVI/HDMI (with DVI to HDMI adaptor) monitor/TV for local output monitoring. www.avenview.com|3...
-
Page 4: Telnet Setting
To access the telnet control in Windows 7, click on the 'Start' menu and type "cmd" in the Search field then press enter. Under Windows XP go to the 'Start' menu and click on "Run", type "cmd" with then press enter. Under Mac OS X, go to Go→Applications→Utilities→Terminal See below for reference. www.avenview.com|4... - Page 5 (For a full list of commands, see Section 1.3). Note: Commands will not be executed unless followed by a carriage return. Commands are case-insensitive. If the IP is changed then the IP Address required for Telnet access will also change accordingly. www.avenview.com|5...
-
Page 6: Rs-232 And Telnet Commands
RS 232 & TELNET COMMANDS All commands will be not executed unless followed with a carriage return (0x0D) and commands are case sensitive www.avenview.com|6... - Page 7 www.avenview.com|7...
-
Page 8: Webgui Control
The 'User Setting' TAB allows the user to reset the IP configuration. The system will require a reboot to the device once any of the settings are changed within this TAB. The IP address needed to access the Web GUI control will also need to be changed accordingly on the web address entry bar. www.avenview.com|8... - Page 9 Click on the 'Control' TAB to toggle power ON/OFF, Input/Output ports, EDID and reset mode. www.avenview.com|9...
-
Page 10: Technical Support
Disclaimer While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview...
Need help?
Do you have a question about the HDM-SWITCHPRO-VW4 and is the answer not in the manual?
Questions and answers