Table of Contents
Advertisement
ANI22
Audio Network Interface
< SET INPUT_METER_MODE PRE_FADER >
< SET INPUT_METER_MODE POST_FADER >
< REP INPUT_METER_MODE PRE_FADER >
< REP INPUT_METER_MODE POST_FADER >
Important Product Information
The equipment is intended to be used in professional audio applications.
Note: This device is not intended to be connected directly to a public internet
network.
EMC conformance to Environment E2: Commercial and Light Industrial.
Testing is based on the use of supplied and recommended cable types. The
use of other than shielded (screened) cable types may degrade EMC perfor-
mance.
Changes or modifications not expressly approved by Shure Incorporated
could void your authority to operate this equipment.
Industry Canada ICES-003 Compliance Label: CAN ICES-3 (B)/NMB-3(B)
Please follow your regional recycling scheme for batteries, packaging, and
electronic waste.
Information to the user
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Specifications
Analog Connections
ANI22-XLR
Active
Inputs
Balanced
ANI22-BLOCK
ANI22-XLR
Impedance
Outputs
Balanced
ANI22-BLOCK
Network Connections (Dante Digital Audio)
(1) RJ45
Channel Count: 2 Inputs, 2 Outputs
Polarity
Non-inverting, any input to any output
Power Requirements
Power over Ethernet (PoE), Class 0. (PoE Plus compatible).
2017/10/10
Command String:
ANI22 Response:
(2) XLR connector
(2) 6-pin block connector
(2) XLR connector
(2) 3-pin block connector
Send one of these commands to the ANI22.
The ANI22 will respond with one of these strings.
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Authorized under the verification provision of FCC Part 15B.
The CE Declaration of Conformity can be obtained from:
www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
Fax: +49-7262-92 49 11 4
Email: info@shure.de
This product meets the Essential Requirements of all relevant European di-
rectives and is eligible for CE marking.
The CE Declaration of Conformity can be obtained from Shure Incorporated
or any of its European representatives. For contact information please visit
www.shure.com
Power Consumption
11W, maximum
Weight
672 g (1.5 lbs)
Dimensions
H x W x D
4 x 14 x 12.8 cm (1.6 x 5.5 x 5.0 in.)
control application
HTML5 Browser-based
Operating Temperature Range
−6.7°C (20°F) to 40°C (104°F)
Storage Temperature Range
−29°C (-20°F) to 74°C (165°F)
Shure Incorporated
23/24
Advertisement
Table of Contents
