Materialdüse (Pos. 3.1) und Materialnadel kpl. (Pos. 3.2) Bestimmungsgemäße Verwendung Düsengröße Artikel-Nr. 2410681 Die Handspritzpistole PILOT 2K Bonding dient ausschließlich der Verarbeitung spritz- barer wasserlöslicher nicht brennbarer Zweikomponenten-Medien. Da sämtliche 2411498 PILOT 2K Bonding materialführende Teile aus Edelstahl-rostfrei gefertigt sind, eignet sich das Modell 2411499 PILOT 2K Bonding zum Auftrag wasserlöslicher Zweikomponenten-Klebstoffe in der...
Technische Beschreibung ► Halten Sie beim Verspritzen von Materialien keine Hände oder andere Körperteile vor die unter Druck stehende Düse der Spritzpistole. Bei der Bonding 2 K handelt es sich um ein Spritzpistolenmodell für den Auftrag von - Verletzungsgefahr. Zweikomponenten - Dispersionsklebstoffen. ►...
(Pos. 18). Alle beweglichen und gleitenden Bauteile müssen vor dem Einbau in den Pistolenkörper Ziehen Sie die Nadeldichtungen (Pos. 17) mit einem Haken aus dem Pistolen- mit WALTHER PILOT Pistolenfett (Art.-Nr.: V 00 000 00 001) eingefettet werden. körper heraus.
Mängel eines Spritzbildes beheben B-Komponente austauschen Die folgende Tabelle zeigt Ihnen, mit welchen Einstellungen Sie das Spritzbild beein- Entfernen Sie den Schlauch von der B-Kom- flussen können. ponente. 24.10 angestrebtes Spritzergebnis Schrauben Sie die beiden Innensechs- 24.7 kantschrauben (Pos. 21) aus der Pistole Spritzbildprobe Abweichung erforderliche Einstellung...
Die Federn sollten ständig mit einem leichten Fettüberzug versehen sein. Eingangsluftdruck: max. 5 bar / 72.5 psi Verwenden Sie dazu WALTHER PILOT Pistolenfett und einen Pinsel. Anschließend Materialdruck: max. 3 bar / 43.5 psi wird die Spritzpistole in umgekehrter Reihenfolge zusammengesetzt.
+49(0)202 / 787 - 2217 Unintended use www.walther-pilot.de • email: info@walther-pilot.de Type designation Two-component hand spray gun Technical description PILOT 2K Bonding Wide jet V 11 820 0x xx3 Safety instructions Round jet V 11 821 0x xx3 Identification of safety instructions...
Page 11
Listing of Replacement Parts PILOT 2K Bonding PILOT 2K Bonding PILOT 2K Bonding PILOT 2K Bonding Wide Jet Round Jet Wide Jet Round Jet V 11 820 0x xx3 V 11 821 0x xx3 V 11 820 0x xx3 V 11 821 0x xx3...
Intended use Nozzle Size Article-No. 2410681 The manual spray gun PILOT 2K Bonding is used exclusively to process sprayable 2411498 water-soluble non-flammable two-component media. Because all material-carrying PILOT 2K Bonding parts are manufactured from stainless steel the model PILOT 2K Bonding is suited...
the pressurized nozzle of the spray gun. - Risk of injury. Technical description ► Never point the spray gun at persons or animals - risk of injury. ► Follow the processing and safety notes of the spraying material and cleaning The Bond 2K is a spray gun model for the application of two-component dispersion agent manufacturers.
Use a hook to pull the needle seals (pos. 17) out of the gun body. Note All movable and sliding parts must be greased with WALTHER PILOT gun grease before installation in the gun body (Art. No.: V 00 000 00 001).
Replacing the component B Correcting spray pattern flaws The following table shows the settings you can use to change the spray pattern. Remove the hose from the B component. 24.10 Unscrew the two hexagon socket screws desired spray result 24.7 (pos.
The springs should always be coated with a thin grease film. intake air pressure: max. 5 bar / 72.5 psi Use WALTHER PILOT gun grease and a brush for this purpose. The spray gun must material pressure: max. 3 bar / 43.5 psi subsequently be reassembled in reverse order.