Related Manuals for Scott Foil Di2
Summary of Contents for Scott Foil Di2
- Page 2 THE NEW FOIL FEATURES THE SAME LIGHTWEIGHT FRAME CHARACTERISTICS AS ITS PREDECESSOR AND IS AMONGST THE LIGHT- EST AERO BIKES ON THE MARKET. THE FRAME AERODYNAMICS OF THE BIKE HAVE BEEN REWORKED FROM THE HEADTUBE ALL THE WAY TO THE REAR DROPOUTS, STIFFNESS AND COMFORT VALUES HAVE BEEN LIFTED TO A NEW LEVEL AND THE INTEGRATED COCKPIT IS JUST ONE EXAMPLE THAT SHOWS HOW FAR COMPONENT INTEGRATION HAS BEEN TAKEN ON THE NEW FOIL.
-
Page 3: Getting Started
GETTING STARTED ELECTRONIC SHIFTING CONFIGUARTION : FRONT BRAKE REAR BRAKE REAR BRAKE FRONT BRAKE Before you start assembling the bike, we recommend doing an inventory check of all parts (components, cables, wires, junctions, etc.), as well as a brief function test of the electronic Shimano Di2 groupset. To do so, connect all Shimano parts and connect via SM-PCE1 or SM-BCR2 to a laptop. - Page 4 Pull it out through the big opening. For English brake setups use the left hole instead. This cable will later connect the junction box (Junction A) with the inter- nal junction box (Junction B). FOIL BUILD UP MANUAL / SCOTT / FOIL / 2016...
- Page 5 Here again, a spoke might help to pull the cable out of the medial hole. tool to ensure a firm connection. Repeat the same procedure on the other side. Mount the brake leavers on the bar. Check that the brake cables are correctly pre-installed. FOIL BUILD UP MANUAL / SCOTT / FOIL / 2016...
- Page 6 Use a bit of oil or grease to reduce the friction. Make sure that the cable housing sits tightly in the foreseen opening of the Make sure the button of the junction box is brake leaver. placed correctly under the hole of the cover. FOIL BUILD UP MANUAL / SCOTT / FOIL / 2016...
- Page 7 Before the rear brake cable is inserted into the frame, make sure 1-1.5Nm using an Allen key. you pre-install cable guides or a shrinking tube in order to hold together the cable housing and the Di2 wire. FOIL BUILD UP MANUAL / SCOTT / FOIL / 2016...
- Page 8 Start mounting the frameset by placing the bigger 1 1/4“ bearing on the fork crown and the smaller 1 1/8” on the top using assembly grease. Add the compression ring Mount the pre-installed Syncros on top of upper bearing. cockpit on the steerer. FOIL BUILD UP MANUAL / SCOTT / FOIL / 2016...
- Page 9 Tighten the expander to 8-10Nm. Use a torque wrench to ensure that you don’t overtighten the bolt. Install the headset expander by sliding it into the steerer under slight tension. FOIL BUILD UP MANUAL / SCOTT / FOIL / 2016...
- Page 10 Finish the handlebar mount by tightening the stem to a maximum of 5Nm. Use a torque wrench to and push them down until they appear at the bottom bracket ensure that you don’t overtighten the stem bolts. opening of the frame. FOIL BUILD UP MANUAL / SCOTT / FOIL / 2016...
- Page 11 Plug the cable the front derailleur mount and connect it with into the internal junction box (Junction B). the internal junction box (Junction B). FOIL BUILD UP MANUAL / SCOTT / FOIL / 2016...
- Page 12 To fix the internal Di2 battery on the bot- tom of the seatpost, place the rubber seals over the battery with the correct side facing down. FOIL BUILD UP MANUAL / SCOTT / FOIL / 2016...
- Page 13 To install the internal seatpost clamp, start by putting grease on the tightening bolt. Make sure no grease reaches the concave tube and out of the bottom bracket box. contact area of the post. FOIL BUILD UP MANUAL / SCOTT / FOIL / 2016...
- Page 14 Slide the seatpost into the frame carefully so as to not damage the Di2 wire. Pull the cable slightly from the bottom. Tighten the bolt of the seatclamp to 5Nm Use a torque wrench to avoid overtightening of the bolt. FOIL BUILD UP MANUAL / SCOTT / FOIL / 2016...
- Page 15 Mount the Shimano Direct Mount rear brake. Pull the brake cable out of the hole on the downside of the downtube. Here again, a spoke might help to get the cable out of the frame. Fix the brake cable on the Shimano Direct Mount rear brake. FOIL BUILD UP MANUAL / SCOTT / FOIL / 2016...
- Page 16 Adjust the brake housing to the correct length so that Shorten the chain to the correct length and mount it by using a chain steering remains unrestricted. tool for Shimano. Make sure the orientation of the chain is correct. FOIL BUILD UP MANUAL / SCOTT / FOIL / 2016...
- Page 17 Wrap the handle bar tape and fix it with tape right after the radius where the bar features a small step. The top of the bar is ergonomically shaped and features an anti-slip coating so that no bar tape is required. FOIL BUILD UP MANUAL / SCOTT / FOIL / 2016...
- Page 18 W I N E V E R Y R I D E FOIL BUILD UP MANUAL / SCOTT / FOIL / 2016...
- Page 19 F O I L B U I L D U P M A N U A L S C O T T | 2 0 1 6 SCOTT-SPORTS.COM...