Changing Internal Switch Settings - Yamaha PM 5000 Series Service Manual

PM5000

CHANGING INTERNAL SWITCH SETTINGS

Internal Switch Settings For Each module
As you tell from the PM5000 block diagram, each module has a number of internal switch settings. These settings can be
changed to "customize" the PM5000 signal flow to most ideally suit your mixing requirements.
The chart below lists the switches and their functions. In some cases two switches must be set appropriately to specify a
function. When changing internal switch settings make only the necessary changes while referring to the block diagram.
= initial factory settings
Switch No./
Module Target
Setting
MONO DIRECT SW105
Input OUT
PRE
POST
POST
AUX PRE SW107
FADER
PRE
POST
STEREO AUX PRE SW106
Input FADER
PRE
POST
Ø SW SW105
MODE
L&R
(Phase SW
Mode)
L ONLY
STEREO Odd- SW102
AUX channel
PRE
MASTER ST AUX
TO
MATRIX
POST
PRE
POST
G/A Odd- SW102
MASTER channel
PRE
G/A TO
MATRIX
POST
PRE
POST
Odd- SW101
channel
PRE
G/A TO
STEREO
POST
ST L TO SW102
MONO MATRIX
PRE
MASTER
POST
PRE
POST
34
Switch No./
Selectable function
Setting
SW106
n/a The direct out signal is pre-EQ (SW106 has
no effect)
PRE The direct out signal is post-EQ, pre-fader
POST The direct out signal is post-fader, post-on
switch
The pre-fader aux signal is sent to the bus
pre-EQ (PRE) or post-EQ (POST)
The pre-fader aux signal is sent to the bus
pre-EQ (PRE) or post-EQ (POST)
Input signal phase inversion is applied to
both stereo channels (L&R) or only the left
channel (L ONLY)
SW103
PRE The odd-numbered channel ST AUX TO
MATRIX signal is pre-fader, pre-on switch
PRE The odd-numbered channel ST AUX TO
MATRIX signal is post-fader, pre-on switch
POST The odd-numbered channel ST AUX TO
MATRIX signal is pre-fader, post-on switch
POST The odd-numbered channel ST AUX TO
MATRIX signal is post-fader, post-on
switch
SW103
PRE The odd-numbered channel G/A TO
MATRIX signal is pre-fader, pre-on switch
PRE The odd-numbered channel G/A TO
MATRIX signal is post-fader, pre-on switch
POST The odd-numbered channel G/A TO
MATRIX signal is pre-fader, post-on switch
POST The odd-numbered channel G/A TO
MATRIX signal is post-fader, post-on
switch
The odd-numbered channel G/A TO
STEREO signal is pre-fader (PRE) or post-
fader (POST)
SW103
PRE The left-channel TO MATRIX signal is pre-
fader, pre-on switch
PRE The left-channel TO MATRIX signal is
post-fader, pre-on switch
POST The left-channel TO MATRIX signal is pre-
fader, post-on switch
POST The left-channel TO MATRIX signal is
post-fader, post-on switch
Switch No./
Module Target
Setting
Even- SW105 SW106
channel
PRE PRE The even-numbered channel ST AUX TO
ST AUX
MATRIX signal is pre-fader, pre-on switch
TO
MATRIX
POST PRE The even-numbered channel ST AUX TO
MATRIX signal is post-fader, pre-on switch
PRE POST The even-numbered channel ST AUX TO
MATRIX signal is pre-fader, post-on switch
POST POST The even-numbered channel ST AUX TO
MATRIX signal is post-fader, post-on
switch
SW105 SW106
PRE PRE The even-numbered channel G/A TO
MATRIX signal is pre-fader, pre-on switch
POST PRE The even-numbered channel G/A TO
MATRIX signal is post-fader, pre-on switch
PRE POST The even-numbered channel G/A TO
MATRIX signal is pre-fader, post-on switch
POST POST The even-numbered channel G/A TO
MATRIX signal is post-fader, post-on
switch
Even-
channel
PRE The even-numbered channel G/A TO
G/A TO
STEREO signal is pre-fader (PRE) or post-
STEREO
POST
fader (POST)
R TO SW105 SW106
MATRIX
PRE PRE The right-channel TO MATRIX signal is
pre-fader, pre-on switch
POST PRE The right-channel TO MATRIX signal is
post-fader, pre-on switch
PRE POST The right-channel TO MATRIX signal is
pre-fader, post-on switch
POST POST The right-channel TO MATRIX signal is
post-fader, post-on switch
Switch No./Setting