RECK MOTOmed gracile12 Short Instructions

MOTOmed gracile12 – Short Instructions
®
Leg trainer (valid as of software version 5.03 – status 12/2011)
1)

Set up:

Place the MOTOmed gracile12 with the big device stand (front tube) facing a wall

1.1) Height adjustment of the pedal axis

d
the set screw . Pull the snap button
f
position . Tighten the set screw

1.2) Horizontal adjustment of the handlebar

loosen the set screw of the horizontal adjustment
the handlebar/operating panel
Sit in a wheelchair or in a stable chair in front of the MOTOmed gracile12 within a reasonable
distance of the trainer – make sure that the knee joints are not stretched out completely
while training, particularly when the foot shells are at the most distant position.
Important: Make sure the wheelchair or chair is secured so that it will not tilt or slip away.
2) Supported inserting and fixing of the feet (if required):
button » foot insertion aid « (
7
with the buttons » pedals forward « and
6
insert one foot after the other in the lower pedal position. Now secure your feet to the
foot shells with the help of the Velcro straps or using the self-operating foot
(fig. 1)
holders .
(accessory)
3) a) Start the training (standard program):
screen appears . Push button
(fig. 4)
will automatically start moving slowly. Let the MOTOmed move your legs for a » passive «
warm-up phase for a few minutes.
b) Selection and start of a preinstalled Therapy Program:
button to activate the start screen
8
program with the buttons
tically return to the start screen
program. Press button
6
automatically start moving slowly.
4)

Passive movement / change of rotation direction:

and » fast « ( )
6
(fig. 7)
revolutions per minute. Slower: by pressing the button
reduced. Faster: by pressing the button
(
button » direction «
4
to backward and vice versa. Note: The buttons
upon the training mode you are in.
5)

Cycle with your own strength or motor-assisted (ServoCycling):

on your own at any time. In order to visualize the transfer to the active training, you can
press button » ServoCycling «
3
message » you are cycling yourself «. With the buttons
you can adjust the resistance according to your muscle strength - from 0 to 20, adapted to
your individual muscle strength.
:
Support the pedal axis
(fig. 2)
e
and bring the pedal axis into the desired
d
.
:
Hold onto the handlebar
(fig. 3)
h
and the user and tighten the set screw
) . Then you can move the foot shells
(fig. 4)
» pedals backward «
5
Press the red » start / stop « button
» leg trainer « to start your training. The foot pedals
6
. Press button
(fig. 4)
or and confirm with button
4
3
, that now shows the name of the selected therapy
(fig. 4)
» leg trainer « to start your therapy session. The foot pedals will
With buttons
you can increase or decrease the passive speed from 1 – 60
» fast « (
6
)
you can change the direction of rotation - from forward
(fig. 7)
and
5 6
. On the display a bicycle appears as well as the
(fig. 6)
5
MOTOmed Movement Therapy: 1. passive, 2. motor-assisted, 3. active resistive
RECK-Technik GmbH & Co. KG, GERMANY
Reckstr.1-5, 88422 Betzenweiler, www.motomed.com
phone +49 7374 18-85, fax +49 7374 18-480, info@motomed.com
c
and loosen
g
and
i
. Adjust the distance between
i
.
In stand-by mode press
b
(fig. 1)
to help you
(not shown)
. The start
8
Press the red » start / stop «
» programs «, mark a therapy
1
» load «. You will automa-
2
» slow « ( )
5
» slow « ( ) the speed is
5
) it is increased. By pressing the
have various functions depending
You can start pedaling
» light « ( ) and » heavy « ( )
6
a
a
.
b
fig.1
fig. 2
fig. 3
1 1 2 2
3 3 4 4 5 5 6 6
fig. 4
1 1 2 2
3 3 4 4 5 5 6 6
fig. 5
1 1 2 2
3 3 4 4 5 5 6 6
fig. 6
page 1/2
c
d
e
f
g
h
i
8
7