Advertisement
Advertisement
Table of Contents
Related Manuals for Jasic JT-315PMWD
Summary of Contents for Jasic JT-315PMWD
- Page 1 A WILKINSON STAR LIMITED PRODUCT 01-19 ISSUE 1...
- Page 2 Contents Section Title Your New Product Safety Product Overview Panel Layouts Control Panel Functions Unpacking Input and Output Connections Maintenance Error Codes Technical Parameters Electrical Schematic A WILKINSON STAR LIMITED PRODUCT 01-19 ISSUE 1...
- Page 3 Your New Product Thank you for selecting this Jasic Technology, Wilkinson Star product. This product manual has been designed to ensure that you get the most from your new product. Please ensure that you are fully conversant with the information provided paying particular attention to the safety precautions.
- Page 4 Insulate yourself from work and ground using dry SAFETY insulating mats or covers big enough to prevent These general safety norms cover both arc welding any physical contact with the work ground. machines and plasma cutting machines unless Never touch the electrode if you are in contact otherwise noted.
- Page 5 form highly toxic and irritating gases. loading and feeding wire during set up and operation. Do not weld on coated metals unless the coating is removed from the weld area, the area is well When feeding wire be careful to avoid pointing it at ventilated and while wearing an air-supplied other people or towards your body.
-
Page 6: Product Overview
Wearers of vital electronic equipment should for ensuring the equipment can be connected, consult their physician before beginning any arc consulting the electricity provider if necessary. welding, cutting, gouging spot welding Materials and their disposal operations. The equipment is manufactured with materials, Do not go near welding equipment with any which do not contain any toxic or poisonous sensitive electronic equipment as the magnetic... - Page 7 pulsed TIG welding, AC-DC hybrid TIG welding and generated by the secondary inverter are smaller, coated electrode MMA welding (DC, AC). It can be the reliability is improved, the energy consumption used in a wide range of welding operations with is lower and the volume is smaller.
- Page 8 Automatic protection The operation panel layout is convenient for various user operations. The machine has excellent protection functions, and there is a corresponding code when protection High quality manual welding can be achieved is enabled. Excellent control algorithm significantly improves machine integrates under-voltage...
-
Page 9: Panel Layouts
PANEL LAYOUTS Front Control panel “+” output socket “-” output socket Remote control socket Gas outlet Rear Cooler unit connector Gas inlet Mains cable Cooler unit fuse 10 Mains switch A WILKINSON STAR LIMITED PRODUCT 01-19 ISSUE 1... -
Page 10: Control Panel Functions
CONTROL PANEL FUNCTIONS Digital display Arc starting mode button Digital display Pulse / no pulse selection button MMA control area Rotary adjustment / push selector Job selection area VRD selection LED Gas purge button VRD on LED AC frequency and balance MMA welding mode selection Parameter LEDs Remote control selection... -
Page 11: Display Features
DISPLAY FEATURES The “V” indicator lights up when the DISPLAY 1 voltage is displayed. Displays voltage value The “JOB” indicator lights up when the Displays “C+ storage storage parameter channel is selected. channel” The “PRG” indicator lights up when the Display “Err”... - Page 12 Arc force MMA Parameter Settings To set the “Arc force” current turn the adjuster MMA parameter zone knob until the “Arc force” LED is lit. Press the adjuster until the LED flashes. Turn the adjuster to increase or decrease the current value. This value is between 0 and 100A added to the set welding current.
- Page 13 released, the current drops over the downslope Pulse mode time (if set) and the arc will extinguish. The post gas Pressing the pulse button will light the will flow for the time set. LED for no pulse or pulse 4T mode For no pulse In 4T mode, when the torch switch is pressed down, For pulse...
- Page 14 Tungsten chart Downslope time (secs). Time the current takes to go from the welding current to the finishing Tungsten electrode Recommended current amperage. size (mm) range (A) Finish amps (amps). Often referred to as the 6--15 crater fill amperage. 16--55 Postflow gas time (secs).
- Page 15 Spot mode When welding in the spot mode use the adjuster to navigate the On LED (1). Press the adjuster (the LED will flash) and adjust to the desired spot time. Press the adjuster to save the parameter (the LED will stop flashing).
- Page 16 Parameter function table Torch switch Manual arc Hot start striking Welding mode Arc force current Hot start striking time mode welding current current MMA DC ● ● ● ● MMA AC ● ● × ● Welding Torch switch mode mode ●...
-
Page 17: Accessories Information
ACCESSORIES INFORMATION Torch switch socket 1. Pin 1, Pin 2 and Pin 3 are for torch current regulation. 2. Pin 4, Pin 5 and Pin 6 are for digital torch connections. Pin 4 -, Pin 5 +, Pin 6 2T/4T. 3. - Page 18 Pin 2 is the common terminal of the potentiometer. It uses the torch control wheel 0 as the starting position. When the current is the minimum, the resistance of Pin 1 and Pin 2 is 10KΩ and the resistance of Pin 2 and Pin 3 is 0Ω. When the wheel rotates to the Current maximum and the current is the maximum, the resistance of Pin 1 regulating...
-
Page 19: Input And Output Connections
MMA welding UNPACKING Before manual welding, pay attention to the Check the packaging for any signs of damage. polarity of the cable connections. There are two Carefully remove the machine and retain the packaging until the installation is complete. connection methods for DC welding, positive electrode connection positive... -
Page 20: Maintenance
outlet connection. The gas inlet hose is connected at the rear of the machine and the other end to a suitable regulator / flowmeter attached to the gas supply cylinder. MAINTENANCE ONLY SUITABLY QUALIFIED PERSONNEL SHOULD CARRY OUT THESE CHECKS WHEN REMOVING ANY COVERS SWITCH OFF AT THE MAINS SUPPLY AND WAIT FOR 5 MINUTES BEFORE... -
Page 21: Error Codes
(higher than a suitably qualified electrician. voltage main circuit. Indicator light is on. 437VAC). Permanently Contact the Jasic UK service Display error code, turns off the Control department. Control board accompanied by alarm Err 5 main circuit;... -
Page 22: Technical Parameters
10 TECHNICAL PARAMETERS Item name Unit Parameters Supply voltage AC400V±15% Input frequency Rated input current 19.5@TIG 21.0@MMA Power capacity 13.50@TIG 14.5@MMA Output current adjustment range (TIG) 10～315 Output current adjustment range (MMA) 10～270 0～100 Arc force current adjustment range Hot start current adjustment range 0～80 No-load voltage VRD voltage... -
Page 23: Electrical Schematic
11 ELECTRICAL SCHEMATIC Mains input cable A WILKINSON STAR LIMITED PRODUCT 01-19 ISSUE 1... - Page 24 JT Series TIG 315MWD Order code ZXJT-315MWD © Wilkinson Star Limited A WILKINSON STAR LIMITED PRODUCT 01-19 ISSUE 1...