Table of Contents
Related Manuals for JCM TBV Series
Summary of Contents for JCM TBV Series
- Page 1 October, 2016 TRAINING ® OVERVIEW Series ™ TBV Transaction Based Validator Phone (800) 683-7248 (702) 651-0000 Fax (702) 651-0214 E-mail support@jcmglobal.com www.jcmglobal.com ® © 2016 JCM American Corporation Part No. 960-100941R_Rev. A...
-
Page 2: Table Of Contents
TBV Transaction Based Validator Unit ........3 Component Locations ............. 4 DIP Switch Settings ..............5 Cleaning Procedures .............. 8 JCM Tool Suite™ Overview ..........10 Firmware Download Procedure ..........11 Calibration ................12 Using the Calibration Program ............... 12 Validation Sensor Calibration ..............12 Positioning Sensor Calibration ............... -
Page 3: Overview
TBV-100 GLD Single note, Gated Bezel, No Cash Box, Centering Path TBV-101 GSH Single note, Gated Bezel, Horizontal Stack Cash Box, Fixed Path TBV-101 ASH Single Note, JCM Standard Bezel, Horizontal Stack Cash Box, Fixed Path TBV T RANSACTION ASED ALIDATOR... -
Page 4: Component Locations
18. BNF Connector (Back Side) (DS6) 19. Transport USB Connector Port 34. Lock & Key Assembly (Option) 20. Denomination INHIBIT/ACCEPT Switches (DS3 [Set identical as DS1]) Figure 2 TBV Component Names Part No. 960-100941R_Rev. A © 2016 JCM American Corporation... -
Page 5: Dip Switch Settings
Table 3 BNF Buzzer Volume Switch DS2 Settings Switch Switch ON Switch OFF N/A* OFF (Fixed) Performance Buzzer ON Performance Buzzer OFF ON Fixed N/A* OFF (Fixed) * Not Applicable (N/A). Never Switched to ON. Lecture Notes Part No. 960-100941R_Rev. A © 2016 JCM American Corporation... - Page 6 Table 5 TBV Photo-Coupler/RS232 Interface Selection Switch DS5 Setting Photo-Coupler RS232 Switch No. Switch ON Switch OFF Photo-Coupler RS232 * Match each setting to DIP Switch DS4 Switches #3 & #4. Lecture Notes Part No. 960-100941R_Rev. A © 2016 JCM American Corporation...
- Page 7 Switch OFF ICB ON ICB OFF* * Initial Switch setting is OFF. When using the ICB, turn the ICB Switch located on the Intelligent Cash Box side to ON. Lecture Notes Part No. 960-100941R_Rev. A © 2016 JCM American Corporation...
-
Page 8: Cleaning Procedures
Table 8 for each Sensor’s cleaning method. Transport Section (Upper Door Open) BNF Section (Upper Portion Open) Validation Section (Lower End Open) Cash Box Frame Section Figure 3 TBV Sensor and Roller Cleaning Locations Part No. 960-100941R_Rev. A © 2016 JCM American Corporation... - Page 9 NOTE: If Sensor Lenses or Prisms become exposed to water, wipe them dry IMMEDIATELY using a soft, dry lint-free Microfiber cloth. Then allow them to air dry for a sufficient amount of time to allow maximum evaporation. Part No. 960-100941R_Rev. A © 2016 JCM American Corporation...
-
Page 10: Jcm Tool Suite™ Overview
Standard Edition Software Program supports the follow- ing Operational Modes and User-selectable Functions (accessible by clicking drop-down menu as shown in Figure 4): Service Mode Table 9 JCM Tool Suite Operational Modes and Functions Service Mode Functions Download Normal (Operational) Mode... -
Page 11: Firmware Download Procedure
NOTE: A BLUE-colored Barograph will display the Download progression. When downloading is complete, the following message is displayed (Figure 5): Download Success. Reset Done. Waiting for USB Cable Disconnection. Figure 5 JCM Downloader Suite Edition Main Screen 4. Verify the (Cyclic Redundancy Check) (Figure 5 a) and the... -
Page 12: Calibration
NOTE: The TBV Unit Front Panel LED will flash WHITE. 4. Connect the Type A-to-Mini B cable between the PC’s USB Port and the USB Port on the front of the TBV Unit. 5. Launch the JCM Tool Suite Standard Edition Software Application. 6. Click the Service Mode drop down menu, then select “... -
Page 13: Positioning Sensor Calibration
4. Connect the Type A-to-Mini B cable between the PC’s USB Port and the USB Port on the front of the TBV Unit. 5. Launch the JCM Tool Suite Standard Edition Software Application. 6. Click the drop down menu, then select “... - Page 14 Calibration Completed NOTE: During the Calibration procedure, a GREEN-colored Barograph will display the test’s progress. 10.Click the “ ” Screen Button once the TBV Positioning Sensor Cal- ibration is complete. Lecture Notes Part No. 960-100941R_Rev. A © 2016 JCM American Corporation...
-
Page 15: Performance Testing Procedures
4. Connect the Type A-to-Mini B cable between the PC’s USB Port and the USB Port on the front of the TBV Unit. 5. Launch the JCM Tool Suite Standard Edition Software Application. 6. Click the drop down menu, then select “... -
Page 16: Operation Tests
- Click the Denomination tab (Figure 10 a) to view the Denomination Screen, then click the “ ” Update Screen Button (Figure 10 b) to confirm the value of the Banknote inserted. Part No. 960-100941R_Rev. A © 2016 JCM American Corporation... - Page 17 Figure 10 TBV Performance Tool Denomination Screen NOTE: To conduct other Acceptance Tests: 1) Close all screens to return to the JCM Tool Suite Main Menu. 2) Allow the TBV Unit to reset. 3) Click the Service Mode drop-down menu, then select “Performance Test.”...
- Page 18 * For Older Firmware versions, LED After Banknote Insertion returns (1) PURPLE Flash. For Newer Firm- ware versions, LED After Banknote Insertion returns Full Denominational PURPLE Flashes (Table 10). Lecture Notes Part No. 960-100941R_Rev. A © 2016 JCM American Corporation...
-
Page 19: Motor Tests
Operational Error Codes on page 27 for details about the Error condition. 3. To end the Test, click the “ ” Screen Button. Stop Figure 11 TBV Performance Tool - Motor Test Options Lecture Notes Part No. 960-100941R_Rev. A © 2016 JCM American Corporation... - Page 20 Tests the operation of the Gated Bezel Flashing GS Shutter Bezel Shutter on the GS BLUE RED Flashing Shutter WHITE Metal Bezel Flashing STOP Ends the Current Test BLUE RED Flashing WHITE Lecture Notes Part No. 960-100941R_Rev. A © 2016 JCM American Corporation...
-
Page 21: Motor Speed Test
The LED Test will cycle automatically with each of the Primary Colors being lit. 2. To end the Test, click the “ ” Screen Button. Stop Figure 12 Motor Speed Test/Device Function Test Screen Part No. 960-100941R_Rev. A © 2016 JCM American Corporation... -
Page 22: Sensor On/Off Test
6. Disconnect electrical power from the TBV Unit. 7. Open the Validation Unit Cover (refer to Figure 3 on page 8). 8. Reapply Power to the TBV Unit. 9. Restart the JCM Tool Suite Standard Edition Software Application. 10.Click the drop down menu, then select “... - Page 23 Detects when the Gate in Flashing GS_LOK the GS Bezel is in the BLUE WHITE Open Position Detects a Banknote BNF Entrance Flashing existing on the BNF BLUE Sensor WHITE Entrance Sensor Part No. 960-100941R_Rev. A © 2016 JCM American Corporation...
- Page 24 Detects a Banknote Flashing BLUE Assignation existing on the BNF WHITE Sensor Middle Sensor Detects a Banknote BNF Reject Flashing existing on the BNF BLUE Sensor WHITE Reject Sensor Lecture Notes Part No. 960-100941R_Rev. A © 2016 JCM American Corporation...
-
Page 25: Dip Switch Test
The Status indicator for each Switch will change from when the Switch position is changed. 4. Click the “ ” Stop Screen Button to end the test. Figure 14 TBV Performance Tool - DIP Switch Tab Part No. 960-100941R_Rev. A © 2016 JCM American Corporation... -
Page 26: Tbv Error Code Tables
[Relative Parts] Side Sensor, Validation Sensor, Feed-Out Sensor, Cash Transport Error Box Feed Out Sensor If the condition is not resolved, change the above related part or parts and complete a full Sensor Calibration procedure. Part No. 960-100941R_Rev. A © 2016 JCM American Corporation... -
Page 27: Operational Error Codes
[Solution] Check for a jammed Banknote or foreign material. Clean the Unit. Shutter Movement [Relative Parts] Shutter Motor, Shutter Sensor If the condition is not resolved, change the above related part or parts. Part No. 960-100941R_Rev. A © 2016 JCM American Corporation... - Page 28 [Solution] Check the Harness connections and the following part. I2C Access [Relative Parts] CPU Board If the condition is not resolved, change the above related part and calibrate the Unit. Part No. 960-100941R_Rev. A © 2016 JCM American Corporation...
- Page 29 During Power Up, valid Calibration was not detected. [Solution] Calibrate the Unit. Calibration [Relative Parts] CPU Board If the condition is not resolved, change the above related part and calibrate the Unit. Lecture Notes Part No. 960-100941R_Rev. A © 2016 JCM American Corporation...
-
Page 30: Icb Error Codes
[Solution] Check ICB Settings and reseat the Cash Box. ICB Module [Relative Part] Cash Box Sensor, ICB Cash Box Module If the condition is not resolved, change the above related part or parts. Part No. 960-100941R_Rev. A © 2016 JCM American Corporation... -
Page 31: Reject Error Codes
[Solution] Check that the Banknote is not damaged or exhibiting unfit conditions. Clean the Unit. Pattern Error [Relative Parts] Validation Sensor If the condition is not resolved, change the above related part. Calibrate the Unit. Part No. 960-100941R_Rev. A © 2016 JCM American Corporation... - Page 32 [Solution] Clean the Banknote path. Check that the Banknote is not damaged or exhibiting unfit conditions. Pattern Error 2 [Relative Parts] Validation Sensor If the condition is not resolved, change the above related part. Calibrate the Unit. Part No. 960-100941R_Rev. A © 2016 JCM American Corporation...
-
Page 33: Ticket Reject Error Codes
The Sensors detected abnormal Barcode magnification, Light print. [Solution] Check the Barcode Coupon for proper printing. Magnification [Relative Parts] Barcode Sensor Abnormal If the condition is not resolved, change the above related part. Calibrate the Unit. Part No. 960-100941R_Rev. A © 2016 JCM American Corporation... - Page 34 If the condition is not resolved, change the above related part or parts. Calibrate the Unit. Reserved Contact your local JCM Service Representative if this error occurs. Reserved Contact your local JCM Service Representative if this error occurs. A Barcode Coupon was inserted into the Unit upside down.
-
Page 35: Calibration Errors
00-08-00 BOX_LOK Box Lock Sensor 00-10-00 GS_HOME Shutter Unit Home Positioning Sensor 00-20-00 BNF_INS BNF Entrance Sensor 01-00-00 BNF_MID BNF Assignation Sensor 02-00-00 BNF_REJ BNF Reject Sensor 04-00-00 Bar Sensor 10-00-00 Part No. 960-100941R_Rev. A © 2016 JCM American Corporation... - Page 36 0000-1000-0000-0000 ull_gre_ref 0000-0000-0008-0000 ul_ore_pen 0000-2000-0000-0000 ul_ir_ref 0000-0000-0010-0000 ur_ore_pen 0000-4000-0000-0000 uc_redr_ref 0000-0000-0020-0000 urr_nir_pen 0000-8000-0000-0000 ur_ir_ref 0000-0000-0040-0000 ull_ir_pen 0001-0000-0000-0000 urr_gre_ref 0000-0000-0080-0000 ul_ir_pen 0002-0000-0000-0000 dc_redl_pen 0000-0000-0100-0000 ur_ir_pen 0004-0000-0000-0000 dll_nir_pen 0000-0000-0200-0000 urr_ir_pen 0008-0000-0000-0000 Lecture Notes Part No. 960-100941R_Rev. A © 2016 JCM American Corporation...
-
Page 37: Tbv Maintenance Equipment
Unit is shown in Figure 15 and listed in Table 21 on page 38. Only the European Connector Version is shown here. Order the “JAC No.” to obtain the USA Style AC Wall Plug. Figure 15 TBV Maintenance Equipment Requirements Lecture Notes Part No. 960-100941R_Rev. A © 2016 JCM American Corporation... -
Page 38: Maintenance Equipment Parts List
UAC iVIZION/TBV Harness (ID-003) G00213 302-100007RA For AC Adapter Power Cord G00286 For UAC AC Adapter * Products that include a “G” in their EDP Numbers are JCM-E developed products. Lecture Notes Part No. 960-100941R_Rev. A © 2016 JCM American Corporation... - Page 39 TBV Transaction Based Validator JCM® Training Overview October, 2016 PERSONAL NOTES AND COMMENTS Part No. 960-100941R_Rev. A © 2016 JCM American Corporation...
- Page 40 "JCM American Corporation has been accredited as an Authorized Provider by the International Association for Continuing Education and Training (IACET)” JCM is a registered trademark of JCM American Corporation. All other product names mentioned herein may be registered trademarks or trademarks of their respective companies.