Table of Contents
Advertisement
Quick Links
- 1 Personal Notes and Comment Area
- 2 Tools and Equipment
- 3 Inspection
- 4 Preventive Maintenance Schedule
- 5 Cash Box Preventive Maintenance
- 6 Cleaning the Validator Head (Monthly/12,000 Cycles)
- 7 Cleaning the Transport (Annual/144,000 Cycles)
- 8 Cleaning the Validator Head (6 Months/72,000 Cycles)
- Download this manual
iVIZION® Banknote Validator
PERSONAL NOTES AND COMMENT AREA
Write any pertinent notes or comments regarding your particular installation
here.
JCM is a registered trademark of JCM American Corporation. All other product names
mentioned herein may be registered trademarks or trademarks of their respective companies.
™
®
©
Furthermore,
,
and
are not always mentioned in each case throughout this publication.
For the Americas & Oceania, E-mail: support@jcmglobal.com
For the UK, Ireland, Europe, Africa, Russia & Middle East, E-mail: support@jcmglobal.eu
For Asia E-mail: asiapactechsupport@jcmglobal.com
Part No. 960-100932R_Rev. A
Operator's Guide
© 2014, JCM American, Corporation
1 6
June, 2014
iVIZION
Preventive Maintenance Instructions
This Guide describes procedures for the cleaning and maintenance of the
iVIZION
Banknote Validator. For additional information, refer to Section 2 of
®
the iVIZION Operation and Maintenance Manual (JCM P/N 960-100929R).
• Notes regarding iVIZION Components:
– Sensor locations are shown in yellow.
– Rollers are shown in blue.
iVIZION REFERENCE DIAGRAMS
Figure 1 identifies the iVIZION
Typical iVIZION Unit
(fully assembled)
Figure 1 iVIZION Unit, Validator Head, Transport Unit and Cash Box
Part No. 960-100932R_Rev. A
June, 2014
Operator's Guide
Operator's Guide
®
Banknote Validator
– Drive Belts are shown in orange.
– Release levers are shown in green.
– Anti-stringing area is shown in red.
™
Validator Head, Transport Unit and Cash Box.
iVIZION Validator Head
iVIZION Head and Transport Unit
iVIZION Transport Unit
iVIZION Cash Box
(inverted)
Typical iVIZION Components
© 2014, JCM American, Corporation
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for JCM iVIZION
Summary of Contents for JCM iVIZION
- Page 1 Validator Head iVIZION Head and Transport Unit Typical iVIZION Unit (fully assembled) JCM is a registered trademark of JCM American Corporation. All other product names mentioned herein may be registered trademarks or trademarks of their respective companies. ™ ®...
- Page 2 NEVER be used. These types of chemicals can cause “hazing” of the imaging and optical sensors, and premature drying out of the Drive Belts and Rollers. NOTE: JCM Global does not recommend the use of any Cleaning Card on the iVIZION Banknote Validator. TOOLS AND EQUIPMENT...
- Page 3 Figure 4 - iVIZION Cash Box (Yellow Area). Reinstall and verify proper operation. INSPECTION 1. Remove the iVIZION Validator from the Machine, and place it on a suitable work surface. 2. Perform a visual inspection of the entire iVIZION Unit. Look for any broken or Typical iVIZION Unit damaged parts that need to be repaired or replaced.
- Page 4 PC on the iVIZION Unit for future reference. NOTE: Be sure to wipe down the entire Bill Path in both the upper and lower 4. If a repair or firmware change is not required, then the iVIZION Cleaning and sections of the Validator Head.
- Page 5 Transport Unit, to expose the rear section 3. Use the JCM Tool Suite application to run the Aging Test. Listen for excessive or of the Transport Unit for cleaning (refer to Figure 3 unusual noise.
- Page 6 NOTE: Refer to Appendix A in the iVIZION Operation and Maintenance Manual (JCM P/N 960-100929R) for Error Codes. 2. Perform a visual inspection of the entire iVIZION Unit (Validator Head and Transport Unit). Look for any broken or damaged parts that need to be repaired ...
- Page 7 PC on the iVIZION Unit for future reference. Inspection required. 3. If a repair, calibration or firmware change is not required, then the iVIZION Inspect Belts for wear or damage in the Validator Head and Cleaning and Preventive Maintenance procedure is complete. The iVIZION Unit Inspection Transport Unit - Repair or replace as required.
- Page 8 5. Clean the Drive Belts in the Validator Head using a clean cloth dampened with NOTE: If necessary, use a Technician’s Cleaning Brush (JCM P/N 501- cleaning solution. The Drive Belts in the iVIZION Validator Head can easily be 000097R) to remove residue build-up from the Belts in the Transport Unit.
Need help?
Do you have a question about the iVIZION and is the answer not in the manual?
Questions and answers