Advertisement
Quick Links
PL Series/PS Series Type B
DIM Module Installation Guide
The DIM module is memory module made by Pro-face for use with its PL Series
Panel Computers (hereafter referred to as the "PL") and Built-in Computers (hereafter
referred to as the "PS-B").
For the details of the applicable models,please refer to each unit's User Manual
(Hardware Manual) or Pro-face Home Page.
URL
http://www.pro-face.com/
(All product names that appear in this manual are the trademarks of their
respective companies.)
Pro-face: Digital Electronics Corporation (in Japan and other countries)
• Be sure to check that the PL/PS-B unit's power is disconnected
before installing the unit, in order to prevent an electrical shock.
• Do not attempt to modify the DIM module, due to the dangers of
shock and fire.
• When installing the DIM module, be sure to read this guide's
sections 1. and 2. completely to insure that the DIM module is
correctly installed.
To Prevent Accidents
• Be sure water, liquids or metal particles are not allowed to enter the unit. Any of
these may cause either a breakdown or an electrical shock.
• Do not place or store this unit in a location where there is direct sunlight, exces-
sive heat, dust or vibration.
• Do not store or operate this unit near chemicals, or where there are chemical fumes.
• Do not use the DIM module in locations where corrosive gasses are present.
• Be careful of static electricity when removing the DIM module from its static-
resistant package.
• Be sure not to touch the DIM module's contact terminals. Touching them with a
bare finger can lead to corrosion.
Unit Disposal
• When the product is disposed of, it should be done so according to your country's
regulations for similar types of industrial waste.
WARNINGS
WARNINGS
-1-
Advertisement
Related Manuals for Pro-face PL Series
Summary of Contents for Pro-face PL Series
- Page 1 PL Series/PS Series Type B DIM Module Installation Guide The DIM module is memory module made by Pro-face for use with its PL Series Panel Computers (hereafter referred to as the "PL") and Built-in Computers (hereafter referred to as the "PS-B").
-
Page 2: Package Contents
Installation Guide (This Guide) Installation Guide Pro-face has taken the utmost care to insure the quality of this product when it was shipped, however, should for any reason problems or damage have occurred during shipping, please contact your Pro-face representative immediately for service. - Page 3 For PL-X920 Series Units Half Cover 1) Unscrew the four (4) attachment screws used to secure the rear maintenance cover and half cover in place. Remove the rear main- tenance cover first, then the half cover. Rear Maintenance PL-X920 Series, 2 slot type Cover Guide Tabs 2) Pivot the half cover open and lift...
- Page 4 For PS-2000B Series Units Cover 1) Lay the PS-B unit on its side and unscrew the four (4) cover at- tachment screws. Step 2 2) Slide the cover horizontally in the direction shown by the arrow (see diagram) and lift it up from the PS-B unit.
- Page 5 You can also remove only the maintenance cover and install the DIM module. To do this, please perform the following steps. 1) Loosen the two (2) maintenance cover attachment screws. attachment screws 2) Tilt the maintenance cover up as shown by the arrow a and lift it out in the direction shown by the arrow b (see diagram).
-
Page 6: Installing The Dim Module
Installing the DIM Module The PL unit has two (2) module sockets and the PS-B unit has one (1). Use the fol- lowing procedure to install a DIM module in your PL/PS-B unit. Be aware that commercial DIM module specifications may differ from mod- ules made by Digital Electronics Corporation and their performance cannot be guaranteed. - Page 7 To Install the DIM Module <For PL> 1) Remove the PL/PS-B unit’s cover. 1. Removing the Cover. DIM Module 2) Install the DIM module in the empty socket. Empty Socket <For PS-B> Rear face of PS-B DIM Module 3) Position the Alignment Grooves so Alignment Grooves that they fit the Alignment Pins.
- Page 8 Please be aware that Digital Electronics Corporation shall not be held liable by the user for any damages, losses, or third party claims arising from the uses of this product. Digital Electronics Corporation 8-2-52 Nanko Higashi, Suminoe-ku, Osaka 559-0031, Japan URL: http://www.pro-face.com/ © 2006 Digital Electronics Corporation...