Amway eSpring 10-0185-CA Owner's Manual page 6

B EL O W C OU N TE R
eSpring FAUCET
®
IN S TA L L ATI O N
(10-0 1 89 - C A )
REVIEW ALL INSTRUCTIONS TO BE SURE YOU HAVE ALL
PARTS AND TOOLS PRIOR TO INSTALLATION.
eSpring Auxiliary Faucet Components (Fig. 18):
a. Spout
b. Spout cap
c. Body with red, green and blue tubes
d. Rubber washer
e. Metal washer
f. Wing nut
g. Supply Connector with flow controller
h. Tubing Removal Tool
NOTE: Supply Connector must be used for all installations.
1. a) Lay the RED and GREEN tubes on the top of the diagram, and lay the BLUE
tube on the bottom. Use a pen to mark them at the arrows (Fig. 19).
b) Use a ruler or lay the tube from the cold water supply on the top of the
diagram and mark a line at ¾" (18mm) or at the arrow (Fig. 19).
2. Press Faucet tap spout into the main body
spout cap onto faucet body top
the wing nut and metal washer while keeping the rubber
washer against the faucet body
3. Holding the foam gasket in place against the faucet
body, lower the eSpring Faucet stem and tubes
through the hole in the sink ledge or counter
With an assistant holding the faucet in place, reach
up from below the counter and slide the wing nut
onto the threaded faucet . Position the faucet in
the desired orientation and tighten the wing nut to
secure the faucet in place
NOTE: If the faucet remains loose, an additional spacer
may be required. Refer to Service Components List, p. 11.
4
d
h
g
and screw
. Unscrew to remove
. (Fig. 20).
Fig. 20
.
(Fig. 21).
Fig. 21
4. Remove the Top Shroud from the Water
Purifier . Remove the Electronic
Module (Fig. 22).
a.
b
c
e
f
5. Insert the GREEN and BLUE tubes
attached to the eSpring Auxiliary Faucet
into their proper locations on the Bracket
(Fig. 23).
NOTE: You will feel resistance before the
Fig. 18
tubes are fully installed. Ensure the tube is
fully pushed in until it meets the mark or the
marks disappear as a check on each of the
tube connections in steps 5-6.
6. Connect the tube from the cold water
supply to the screen side of the Supply
Connector
water flow direction
tube attached to the Auxiliary Faucet into
the opposite end of the Supply Connector
(Fig. 24).
NOTE: You must use the Supply Connector (Fig.
18, part c) between the valve at the water
supply and the eSpring Faucet.
Fig. 19
7. Open the eSpring Faucet
Open the water supply shut-off
valve to start water flowing
through the Water Purifier
(Fig. 25).
NOTE: It will take a short time for
water to saturate the Cartridge and
flow from the Faucet. Flush for a
minimum of 5 U.S. gallons (20 liters)
(approximately 5-15 minutes) to
remove air pockets and carbon dust.
If water is not clear,
see Troubleshooting, p. 8.
8. Turn off the eSpring Faucet and check for any signs of leakage at all
tubing connections
Troubleshooting, p. 7.
NOTE: Purchase 10-1398 to use in installation to a refrigerator or other
secondary device.
NOTE: During use periodically check system for leaks.
9. Skip to COMPLETING THE INSTALLATION, p. 10.
Fig. 22
. Arrow in balloon shows
. Insert the RED
.
(Fig. 25). If there is leaking or bubbling, refer to
Fig. 23
Fig. 24
Fig. 25