FAAC 550 Manual
Hide thumbs Also See for 550:

Advertisement

550
550 MPD
550
550 MPD
&
&
UNI EN ISO 9001-085

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 550 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for FAAC 550

  • Page 1 550 MPD 550 MPD & & UNI EN ISO 9001-085...
  • Page 2: General Safety Regulations

    5) This product has been designed and manufactured only for the use 17) Each installation must be fitted with at least one flashing light (e.g. FAAC stated in this manual. Any other use not expressly set forth will affect LAMP, MINILAMP, etc.) as well as a warning plate suitably fixed to the...
  • Page 3: Description And Technical Specifications

    Housing protection IP 31 device. IP 44 (with Kit) The 550 automation system allows two operators (550 I + 550 Max. door width (m) 3 (1 operator) Slave) to be installed on the same door. The 550 automation system has been designed and constructed 4 (2 operators) for vehicle access control.
  • Page 4: Assembly Sequence

    In accordance with the measurements given in Table 1, install either a single operator (550 I) at the centre of the door as shown in Fig. 6 or two operators (one 550 I and one 550 Slave) at the sides of the door as shown in Fig. 7.
  • Page 5 ENGLISH ENGLISH • double section garage door 3) Fix the operator to the back plate using the nuts and bolts (Fig. 9) provided, as shown in Fig. 11. When the door is closed, the 4) Weld the upper telescopic arm fixing brackets in the position axis of rotation of the drive shaft described in the instructions for the specific type of garage must be about 10 cm below...
  • Page 6 Observe points 10, 11, 12, 13 and 14 of the GENERAL SAFETY OBLIGATIONS. Observing the indications in Fig.3, install the raceways and make the electric connections from the 550 MPD control board to the selected accessories. Always separate power cables from control and safety cables (push-button, receiver, photocells, etc.).
  • Page 7: Electric Connections

    Flashing lamp: connect a flashing lamp with max. power of 60W between terminals 15 and 16. Courtesy lamp: connect the courtesy lamp of the 550 Slave or the outside courtesy lamp with max. power of 250W between terminals 14 and 16.
  • Page 8: Basic Programming

    ENGLISH ENGLISH 9 = STOP = STOP Command (N.C.) The following table shows the sequence of functions accessible This is any device (e.g. a push-button) which, by opening in BASIC PROGRAMMING: a contact, stops door movement. To install several stop devices, connect the N.C. contacts BASIC PROGRAMMING in series.
  • Page 9 "COM,OP,CL" terminals of the 550MPD control board = FCA : Stops after a 3-sec. deceleration and the 550 Slave card, and if you have to reverse phases, reverse FCC : Stops after a 2-sec. deceleration them for both motors.
  • Page 10: Manual Operation

    7. MANUAL OPERATION - From inside (Fig. 20) The operator 550 is equipped with an emergency release device Insert the hex wrench provided and turn clockwise about half a that can be operated from inside the garage. On request, a lock turn until the stop is reached.
  • Page 11: General Safety Rules

    Anti-crushing safety is assured by an adjustable electronic device. SBLOCCA/UNLOCK DEBLOQUE/ENTRIEGELT The 550 automation system allows two operators (550 I + 550 DESBLOQUEAR Slave) to be installed on the same door. BLOCCA/LOCK BLOQUE/VERRIEGELT The door is normally closed.
  • Page 12 Le descrizioni e le illustrazioni del presente manuale non sono impegnative. La FAAC si riserva il diritto, lasciando inalterate le caratteristiche essenziali dell’apparecchiatura, di apportare in qualunque momento e senza impegnarsi ad aggiornare la presente pubblicazione, le modifiche che essa ritiene convenienti per miglioramenti tecnici o per qualsiasi altra esigenza di carattere costruttivo o commerciale.

This manual is also suitable for:

550 mpd

Table of Contents