Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for FAAC 740
Summary of Contents for FAAC 740
- Page 1 740-741 & 740-741 & 740D 740D...
-
Page 2: Ec Declaration Of Conformity For Machines
“16”. 6) FAAC declines all liability caused by improper use or use other than that 18) FAAC declines all liability as concerns safety and efficient operation for which the automated system was intended. - Page 3 The non-reversing reduction system ensures the gate is mechanically locked when the gearmotor is not operating, therefore it is not The 740-741 gearmotor was designed and built for controlling vehicle necessary to install any electric lock access. AVOID ANY OTHER USE WHATEVER.
- Page 4 With reference to IEC 34-1 Stan- sheaths for routing the cables. Using a spirit level, check if the dard, the 740-741 gearmotor with plate is perfectly level. Wait for the cement to set. an S3 duty, can operate at a use 4- Lay the electric cables for connection to the accessories and frequency of 30-40%.
- Page 5 Values are expressed in mm Values are expressed in mm Fig.15 6. START-UP Fig.10 6.1. Control board connection 5.4. Assembling the rack Before attempting any work on the board (connections, programming, maintenance), always turn off power. 5.4.1. Steel rack to weld (Fig. 11) Follow points 10, 11, 12, 13 and14 of the GENERAL SAFETY 1) Fit the three threaded pawls on the rack element, positioning OBLIGATIONS.
- Page 6 Fig.19 Fig.18 Fig.26 Fig.25 8. MANUAL OPERATION Warning: Cut power to the system to prevent an involuntary pulse from activating the gate during the release manoeuvre. To release the operator proceed as follows: 1) Insert the key provided and turn it clockwise as shown in Fig. 27 ref.
- Page 7 CONTROL BOARD 740D WARNINGS LAYOUT AND COMPONENTS Important: Before attempting any work on the control board (connections, maintenance), always turn off power. - Install, upstream of the system, a differential thermal breaker with adequate tripping threshold. - Connect the earth cable to the appropriate terminal on the J7 connector of the equipment (see fig.
- Page 8 4.1. Connection of photocells and safety devices Connection of an "edge" safety device Before connecting the photocells (or other devices) we advise you to select the type of operation according to the movement area they have to protect (see fig. 31): 9 10 11 12 Opening safety Opening/closing...
- Page 9 Connection of a pair of closing photocells and a pair of Connection of two pairs of closing photocells and two opening/closing photocells edge safety devices 9 10 11 12 9 10 11 12 RX CL TX CL RX CL1 TX CL1 TX CL2 RX CL2 TX OP/CL...
- Page 10 FSW OP - Opening safety devices contact (terminal 3): The 4.5. Connector J2 - Rapid connection to Minidec, purpose of the opening safety devices is to protect the leaf Decoder and RP movement area during opening. During opening, in the A- This is used for rapid connection of Minidec, Decoder and RP AP-S-E-EP logics the safety devices reverse the movement receivers (see fig.
- Page 11 5.2. ADVANCED PROGRAMMING 5. PROGRAMMING To access ADVANCED PROGRAMMING, press key F and, as you To program operation of the automated system, you have to hold it down, press key access the " PROGRAMMING " mode. Programming is split into two parts: BASIC and ADVANCED . •if you release key + , the display indicates the name of the first function.
- Page 12 Display Function Default Display Function Default INDICATOR-LIGHT: ENCODER: If the encoder is used, you may select its is selected, the output functions as a presence. standard indicator-light (lighted at opening If the encoder is present and enabled, and pause, flashing at closing, and off when "decelerations"...
- Page 13 6. START-UP Display Function Default WORK TIME (time-out): 6.1. INPUTS CHECK We advise you to set a value of 5 to 10 The table below shows the status of the LEDs in relation to to the seconds over the time taken by the gate to status of the inputs.
- Page 16 Manual opening is, therefore, only possible by using the release system. If installed and used correctly, the 740-741 automated system will The gearmotor does not have a mechanical clutch and, therefore, it ensure a high degree of safety.
- Page 18 Le descrizioni e le illustrazioni del presente manuale non sono impegnative. La FAAC si riserva il diritto, lasciando inalterate le caratteristiche essenziali dell’apparecchiatura, di apportare in qualunque momento e senza impegnarsi ad aggiornare la presente pubblicazione, le modifiche che essa ritiene convenienti per miglioramenti tecnici o per qualsiasi altra esigenza di carattere costruttivo o commerciale.
Need help?
Do you have a question about the 740 and is the answer not in the manual?
Questions and answers