Multi-Pin (Mass Termination) Connector Card - Keithley 7015-S Instruction Manual

Card Connections & Installation
3.3.4 Multi-pin (mass termination) connector
card
Since connections to external circuitry are made at the 96-pin
male DIN bulkhead connector, there is no need to separate
the connector card from the relay card. If the connector card
is separated from the relay card, carefully mate them togeth-
er and install the supplied 4-40 mounting screw. Be sure to
handle the cards by the edges and shields to avoid contami-
nation.
Table 3-3
Multipin card terminal identification
Connector Schem.
Mux Desig. Desig.
Terminal 1a-32c 1-96
Bank A
Input 1 HI 32c 96
LO 32b 64
Input 2 HI 32a 32
LO 31c 95
Input 3 HI 31b 63
LO 31a 31
Input 4 HI 30c 94
LO 30b 62
Input 5 HI 30a 30
LO 29c 93
Input 6 HI 29b 61
LO 29a 29
Input 7 HI 28c 92
LO 28b 60
Input 8 HI 28a 28
LO 27c 91
Input 9 HI 27b 59
LO 27a 27
Input 10 HI 26c 90
LO 26b 58
Output HI 26a 26
LO 25c 89
Notes: 1. Pins 9a and 9b (pins 9 and 41 on schematic) are shield.
2. Short pin 1a to 1b on the mating connector (pins 1 and 33 on schematic) to allow the output relays on the connector card to close.
Pins of the Model 7015-C mass termination connector can be identified in one of three ways:
1. Mux terminal, consisting of banks A-D and inputs 1-10.
2. Connector description, consisting of rows a-c and columns 1-32.
3. Schematic and component layout designation (1-96).
3-6
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Connector Schem.
Mux Desig. Desig.
Terminal 1a-32c 1-96
Bank B
Input 1 HI 24c 88
LO 24b 56
Input 2 HI 24a 24
LO 23c 87
Input 3 HI 23b 55
LO 23a 23
Input 4 HI 22c 86
LO 22b 54
Input 5 HI 22a 22
LO 21c 85
Input 6 HI 21b 53
LO 21a 21
Input 7 HI 20c 84
LO 20b 52
Input 8 HI 20a 20
LO 19c 83
Input 9 HI 19b 51
LO 19a 19
Input 10 HI 18c 82
LO 18b 50
Output HI 18a 18
LO 17c 81
Terminal identification for the DIN connector of the multi-
pin connector card is provided by Table 3-3. This connector
will mate to a 96-pin female DIN connector.
Keithley has a variety of cable and connector accessories
available to accommodate connections from the connector
card to test instrumentation and DUT (devices under test). In
general, these accessories, which are summarized in Table 3-
4, utilize a round cable assembly for connections.
Connector Schem.
Mux Desig. Desig.
Terminal 1a-32c 1-96
Bank C
Input 1 HI 16c 80
LO 16b 48
Input 2 HI 16a 16
LO 15c 79
Input 3 HI 15b 47
LO 15a 15
Input 4 HI 14c 78
LO 14b 46
Input 5 HI 14a 14
LO 13c 77
Input 6 HI 13b 45
LO 13a 13
Input 7 HI 12c 76
LO 12b 44
Input 8 HI 12a 12
LO 11c 75
Input 9 HI 11b 43
LO 11a 11
Input 10 HI 10c 74
LO 10b 42
Output HI 10a 10
LO 9c 73
Connector Schem.
Mux Desig. Desig.
Terminal 1a-32c 1-96
Bank D
Input 1 HI 8c 72
LO 8b 40
Input 2 HI 8a 8
LO 7c 71
Input 3 HI 7b 39
LO 7a 7
Input 4 HI 6c 70
LO 6b 38
Input 5 HI 6a 6
LO 5c 69
Input 6 HI 5b 37
LO 5a 5
Input 7 HI 4c 68
LO 4b 36
Input 8 HI 4a 4
LO 3c 67
Input 9 HI 3b 35
LO 3a 3
Input 10 HI 2c 66
LO 2b 34
Output HI 2a 2
LO 1c 65