Solight TE76 Instructions For Use

EN Solight TE76 METEOROLOGICAL STATION
Instructions for use
Instructions for use
Dear customer, thank you for buying our product. If you would like to use it safely and get the most out of it then please read through these instructions carefully
and follow them. That way you will avoid incorrect use or damage. Prevent unauthorised use of this device and always respect all rules related to handling
electronic devices. Keep the instructions for use in case you need them later. The main unit should stand as close to a window as possible.
TECHNICAL INFORMATION
Room temperature
measurement
Room humidity measurement
Outdoor temperature
measurement
Outdoor humidity measurement
Power supply
Temperature measurement
accuracy
Humidity measurement
accuracy
Main unit
In the case of charging using batteries open the battery cover and insert three AAA alkaline batteries. Observe the marked polarities. When switching on all
segments the LCD display will light up for a moment and the device will beep. Then it will go into standard mode of measuring temperature and humidity.
In the case of charging using a AC/DC adapter connect the charging connector to the input socket at the meteorological station and then connect to an electrical
socket.
Reset the equipment by removing the batteries or disconnecting the adapter for at least five seconds. That will return the settings to their defaults and will delete
the memory. In the case of charging using batteries the display lights up and stays lit for eight seconds each time. In the case of charging using an adapter it is lit
constantly.
You can only pair up the main unit with three sensors. Each sensor is charged by two AAA alkaline batteries.
Initial settings: 24-hour time format shows 00:00, pressure is in hPa units, and temperature is in °C
1. FUNCTIONS OF BUTTONS
Function
Control
Short
Switch between display
press
of time and alarms (AL)
Standard
mode
Long Enter into time and
press date setup mode
Short
Switch/Confirm setting
press
Time setting
Long
press
Short
Switch/confirm setting
press
Alarm setting
Long
press
Short
press
Set up
temperature
alarm
Long
press
2. MAIN FUNCTIONS

Date and time (days of the week in seven languages – English, German, French, Italian, Dutch, Spanish and Danish

12-hour or 24-hour time format

Two alarms

Alarm with SNOOZE function (interval adjustable from 3 to 20 minutes, default setting 5 minutes)

RCC signal reception mode: DCC

Measurement of temperature in °C or °F

Measurement of room temperature – range from 0°C - +50°C, accuracy of measurement +/- 1°C, scope of display (0°C to +50°C)
0°C to +50°
25% to 95%
-30°C to +60°C
25% to 95%
3x AAA 1.5V alkaline battery
AC/DC adapter 5V/1,200mA
1°C
5%
MODE ALARM
Switch alarm on and off
Delete information about
maximum/minimum
temperature/humidity
-----
----- -----
-----
----- -----
----- -----
----- -----
We recommend using alkaline batteries with a rated voltage of 1.5V for
the LCD display to be the correct luminescence. Rechargeable NiMH
batteries usually have a 1.2V rated voltage and the luminescence of the
LCD display is therefore worse.
ALERTS UP
Switch
Switch between
between
max/min
°C/°F
Enter into
Switch
temperature
barometer
alarm setup
HPa/inHg
function
One step
-----
forwards
Forwards at a
speed of 8
-----
steps per
second
One step
-----
forwards
Forwards at a
speed of 8
-----
steps per
second
Switch
Switch/confirm temperature
setting alarm on and
off
One step
-----
forwards
DOWN CHANNEL
Switch
Switch between
between
CH 1, 2, 3
12h/24h
Enter into snooze
Activate RCC Pair transmitter
signal with receiver on
reception current channel
One step
-----
back
Back at a
speed of 8
steps per -----
second
One step
-----
back
Back at a
speed of 8
-----
steps per
second
Switch
temperature
-----
alarm on
and off
One step
-----
back
SNOOZE/LIGHT
Switch between
under-lighting
modes
setup mode
-----
-----
-----
-----
-----
-----