Set Error - Toshiba R410A Service Manual

3
Set ON time by , buttons,
MM
HH
and then push button.
SET
When push button, the
SET
flashed ON time (8:00 in example)
change, and OFF time of the
program 1 flashes at the same
time.
PROGRAM1
PROGRAM2
PROGRAM3
4
Set OFF time by / buttons, and then push
HH MM
button.
When pushing button, the flashed ON time (12:00 in
SET
example) changes, and ON time of the program 2 flashes.
5
Next set up the operation time to the program 2 and 3.
When pushing button after OFF time of the program
SET
3 has been set, the flashed OFF time (19:00 in example)
changes and ON time of the program 1 flashes.
6
Finally, push button.
PROGRAM
Push button within 30 seconds after No. 5 step.
PROGRAM
Then, one day timer (Monday in example) is set completely.
ON/OFF is displayed when the present time is included
in the range of the set time.
(In the above status, the contents of the program 1 are
displayed as the present time is included in the range from
ON time to OFF time of the program 1.)
7
Setting to other da y, repeat abo ve pr ocedure fr om
If you need to set the same time as previous setting. Refer to "7. How to copy the
program operation time".
CAUTION
• Setup of the program time : is treated as
(Example) In the following cases, setup are available.
ON time OFF time
• If 30 seconds have passed while the button is flashing without pushing
buttons, the display returns automatically to the original display (Normal display).
In this case, repeat the procedure from the 1st step.
SuMoTuWeTh Fr Sa
PROGRAM1
ERROR
PROGRAM2
PROGRAM3
6
WEEKLY TIMER
3, 4, 5
PROGRAM DAY SET CANCEL
HH MM CLEAR CHECK
3, 4
SET
PROGRAM1
PROGRAM2
PROGRAM3
PROGRAM1
PROGRAM2
PROGRAM3
PROGRAM1
PROGRAM2
PROGRAM3
1 6
to .
.
or /
DAY HH MM

6. Set error

If flashing is displayed when the program operation has been set up, correct the
ERROR
time following the procedure below.
1. When flashing is displayed, ON time of the failed program flashes.
ERROR
PROGRAM1
PROGRAM2
PROGRAM3
2. Push button to flash the time to be corrected.
SET
3. Using / buttons, correct ON/OFF time.
MM
HH
4. Push button. When the setup is correctly performed,
SET
5. The correction has completed by pushing
CAUTION
• When ON/OFF time is set as follows,
ERROR
1) When a part of the operation time makes inroads into a part of another operation time
Example: ON time OFF time
2) When OFF time is ahead of ON time
Example: ON time OFF time
3) When ON time is same as OFF time
Example: ON time OFF time
4) ON time or OFF time is singly set up
Example: ON time OFF time
[Is not set]
• The following cases are not set error.
1) OFF time of the previous cycle is same as ON time of the next cycle.
Example: ON time OFF time
2) When the next cycle is set to the time before the
set time of the previous cycle
Example:
ON time OFF time ON time
Pushing the button changes the order in order of time.
PROGRAM
3) When both ON and OFF times are same
Example: ON time OFF time
SuMoTuWeTh Fr Sa
ERROR
display disappears.
ERROR
button.
PROGRAM
is displayed.
0:00 23:59
ON OFF
ON OFF
0:00 23:59
OFF ON
0:00 23:59
ON OFF
0:00 23:59
ON OFF
0:00 23:59
ON OFF
ON OFF
0:00 23:59
OFF time
ON OFF
ON OFF
Continuous operation
for 24 hours