Advertisement
Quick Links
1. Operating safety precautions
This product complies with the requirements of the following European
Community Directives: 89/336/EC (Electromagnetic Compatibility).
* Introduction
This electronic measuring instrument is a high technology products made
under strict quality control. We guarantee its exceptional precision and
utmost reliability. To ensure safe operation of this instrument, be sure to
follow the warning and precautions provided as bellow.
Warning !
* Do not use this product or equipment connected to it in an explosive,
ignitable, or flammable atmosphere, as this will result in the risk of
explosion.
* Do not connect this product to a piece of equipment or cable having
a voltage with respect to ground on its chassis, as such connection
can result in the risk of electrical shock.
* Use a proper Battery charger for charging internal rechargeable
battery pack.
Caution
* Do not remove the case cover, as this can risk failures or loss of
performance.
* Do not allow water to enter the product. This product is not waterproof.
* If condensation forms on this product due to a sudden change in
temperature, use this product only after allowing it to dry sufficiently.
-19-
Advertisement
Related Manuals for PeakTech 9017
Summary of Contents for PeakTech 9017
- Page 1 1. Operating safety precautions This product complies with the requirements of the following European Community Directives: 89/336/EC (Electromagnetic Compatibility). * Introduction This electronic measuring instrument is a high technology products made under strict quality control. We guarantee its exceptional precision and utmost reliability.
- Page 2 2. Introduction This professional SAT Level Meter has been designed for the installation and maintenance of analogue and digital satellite TV system. The inside circuitry and mechanical design has been carefully developed in order to obtain very light, slim typed field strength meter. To allow the installer to work in the best conditions, it is also offering built-in LNB powering and hang-on-the neck type carrying case.
- Page 3 Level Measurement - Measuring Range 40 to 80 dBuV (-67 to –27 dBm) - Resolution 0.1 dB ± 3 dB (0 to 40°C) - Accuracy - Bandwidth 27 MHz (- 3 dB) RF Input F type , 75 ohm Output signal to Antenna System 13 V, 18 V, 22 kHz, DiSEqC 1.0 signal LNB Current Measurement 0 to 250 mA with 0.1 mA resolution...
- Page 4 Environmental Conditions 0 to 40 °C - Operating Temperature Range - Operating Humidity Range 30 to 85 % RH -10 to 50 °C - Storage Temperature Range Dimensions and Weight 180(W) x 75(H) x 150(D) mm Approx. 1.5 kg Supplied Standard Accessories 1 x Battery Charger (12V / 500mA) 1 x Carrying Case 1 x User’s Manual...
- Page 5 4.2. Cooling and Ventilation No special cooling and ventilation is required. However, the instrument should be operated where the ambient temperature is maintained. 5. Operation Procedure 5.1. Front Panel Description 1. Power; Power on / off (Momentary switch). Turning on the power with beep sound when the switch is pressed. 2.
- Page 6 3 Function; - Set the frequency, Function, Output Signal and units. - Store the function and data for desired channel and call the stored channel. - Turning on back-light. Use to select the function of Up/Down key. (Frequency, Channel, Function, Output signal, unit) Use to store the desired conditions of each channel (push two times) (Frequency, Function, Audio Sub- carrier, measuring unit) Use to change the measuring...
- Page 7 5.2. LCD Panel Description 1. Bar-Graph; Displays signal level. Minor division indicates 1 dBuV. Same quantities of bar will be displayed with input level from 40dBuV to 80dBuV. 2. Function (Peak holder, Sound, Battery level) Displays selected function (Peak, Sound) and the level of internal battery pack.
- Page 8 6. Units Displays selected units (dBuV and dBm for level, mADC for current) 7. Output signal to antenna signal displays selected output signal to LNB or antenna system. 13 V, 18 V, 13 V with 22 kHz, 18 V with 22 kHz, DiSEqC signal (A, B, C, D) 6.
- Page 9 6.1.2. Setup for Multi-Site Viewing Figure 3-3 is shown a set-up example for two LNB (or antenna) system. When connect this meter to the outlet (or Output of switch Box), connect through “DC Block” to cut the OUTPUT Signal form this meter. Refer to Section 6.1.1: “Connecting with LNB”...
- Page 10 6.1.4. Setup Function of measurements The measuring function (Normal, Peak Holder, Sound monitoring) can be selected. a. Move to “Function” selection group by using “Shift” key. Function group will be blinking. b. Select desired function by using “Up/Down” key. - Sound: Acoustic signal strength monitoring - Peak Holder: Displayed Measuring level is changed when new measuring level is higher than previous measured value.
- Page 11 To set up outputs for antenna system(LNB), check the required signal of LNB. (DiSEqC A, B, C, D) a. Move to “DiSEqC Output” selection group by using “Shift” key. DiSEqC group will be blinking. b. Select desired DiSEqC signal(A,B,C,D) by using “Up/Down”...
- Page 12 6.1.8. Change of Channel Number a. Move to “Ch” selection by using “Shift” key. “Ch” will be blinking. b. Select desired channel by using “Up” / “Down” key. (Ch 01…99) c. Move to other selecting function by using “Shift” key or push “Store”...
- Page 13 6.1.11. Indicating the level of internal battery ( The level of internal battery is displayed on “Battery indicator”. Refer to following table for the status of battery voltage. Battery sign of Indicator Battery Voltage Three bars of Approx. 2 hrs. indicator Two bars of indicator Approx.
- Page 14 6.3. Additional Functions 6.3.1. Peak Holder ( This meter has “Peak Holder function” to support easy installation of antenna system by detecting highest input level. The displayed measuring level is changed when new measuring level is higher than previous measured value. To set this function, see to 6.1.4.
- Page 15 7.2. Battery charging CAUTION and NOTE that the battery should be fully charged after first opening the box. The first time charging is important. Always keep the battery level fully charged before and after use. For charging, we recommend you following ways. 7.3.
- Page 16 We herewith confirm, that the units are calibrated by the factory according to the specifications as per the technical specifications. We recommend to calibrate the unit again, after 1 year. ® © PeakTech 06/2007 -34-...
Need help?
Do you have a question about the 9017 and is the answer not in the manual?
Questions and answers