Table of Contents
Advertisement
Quick Links
All manuals and user guides at all-guides.com
Creative Musical Interface
OWNER'S MANUAL
NOTE
１． VESTAX insulater is needed (not included) when the QFO is placed horizontaly to suppress
howling under high volume use.
２． VESTAX QFO strap hook(not included) will be needed when playing the QFO strapped around
shoulder or hip.
※Attachment instructions are shown on page 16
Advertisement
Table of Contents
Related Manuals for Vestax QFO
Summary of Contents for Vestax QFO
- Page 1 All manuals and user guides at all-guides.com Creative Musical Interface OWNER'S MANUAL NOTE １． VESTAX insulater is needed (not included) when the QFO is placed horizontaly to suppress howling under high volume use. ２． VESTAX QFO strap hook(not included) will be needed when playing the QFO strapped around shoulder or hip. ...
-
Page 2: Table Of Contents
All manuals and user guides at all-guides.com CONGRATULATIONS！ Thank you for purchasing the Vestax QFO Creative Musical Interface. We suggest that you read through this owner's manual thoroughly so that you may enjoy the full use of this product safety and in the knowledge of all its special features and suitablyapplications. CONTENTS C A U T I O N ... -
Page 3: Important Safeguards
All manuals and user guides at all-guides.com IMPORTANT SAFEGUARDS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. 1.Read instructions-All the safety and operating 11. Grounding or Polarization-This product is equipped instructions should be read before the appliance is with a polarized alternating-current line plug (a plug operated. having one blade wider than the other). This piug 2.Retain ... -
Page 4: Features
19.Replacement Parts-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characterristics as the original parts. Unauthorized substitutions may result in fire, electric FEATURES ●This is the very first model designed by Q-BERT which has DJ Mixer and Turntable in one united body. ●The Dynamic Balance A.S.T.S. allows the needle to trace the groove at any angle with no skipping or tracing error. ●The heart of machine, motor has proven its high stability and reliability in Vestax PDX-2000series. The motor is our original high torque direct drive. ●Vestax PMC-05 PROs reliable circuitry is loaded ●Spin slide pitch controller placed around the platter(MAX ±60%).Linking pitch moves and scratches are possible. -
Page 5: Anti Skipping Tone-Arm System)
All manuals and user guides at all-guides.com A.S.T.S(Anti Skipping Tone-arm System) A.S.T.S(Anti Skipping Tone-arm System) has been developed with years of experience and a number of trials, searching for the innovative tone-arm for professional DJ's.This system breaks all of the historic common sense, achieving its ... -
Page 6: Functions
All manuals and user guides at all-guides.com FUNCTIONS ■MIXER SECTION TOP PANEL （Side） POWER MASTER LEVEL TRIM TRIM -12dB +12dB -12dB +12dB -24dB +12dB -24dB +12dB PHONO PHONO LINE LINE LEVEL LEVEL （Bottom） （Bottom） Hook （sold seperate） PITCH - 60 PHONES PHONES （Side）... - Page 7 !5 I .F. REVERSE SWITCH !6 C .F. REVERSE SWITCH Reverses the action of the input fader by marking the Reverses the action of the cross fader by switching zero point top instead of bottom. PGM1 and 2. REAR PANEL MODEL NO. QFO 100V 50/60Hz 15W MADE IN CHINA SERIAL NO. LINE MASTER LINE REAR PANEL...
-
Page 8: Turntable Section
All manuals and user guides at all-guides.com ■TURNTABLE SECTION Balance Weight （Option） Dynamic Stylus Pressure Adjustment Knob Tone-Arm Height Fixed Screw Arm Rest Tone Arm POWER MASTER LEVEL Lock Ring TRIM TRIM Headshell -12dB +12dB -12dB +12dB Slip Mat （Option） -24dB +12dB -24dB +12dB PHONO PHONO Platter （ Option） LINE LINE LEVEL LEVEL... -
Page 9: Assembly And Set-Up
All manuals and user guides at all-guides.com +60％ -60％ 0％ 0％ -60％ -60％ +60％ +60％ -60％ 0％ 0％ 0％ 0％ -60％ -60％ ASSEMBLY AND SET-UP Turntable Assembly (1)Place the platter on the center spindle. The platter will adjust itself to best fit over the spindle. DRIVER (2)Adjust the positioning of a platter so that a screw goes into a screw holes. (3)Tighten screws using a driver and fix a platter and a main unit. ... - Page 10 All manuals and user guides at all-guides.com Slip mat Place the slip mat on the platter. Then place a record on top of the slip mat. By using a slip mat, it becomes possible to stop a record board by hand during rotation of a platter or to make it reverse. Moreover, if an optional slip-sheet is set and used, it will take effect more. Top:Record disc side(Printed side) Cartridge Installation Bottom:Slip surface side (1)Make sure that you follow the instructions included with your cartridge. (2)Connect the lead wires to the respective terminals. Industry ...
-
Page 11: Installation And Connection
FAILURE to do so many result in shock and isolate the unit from sound radiation from them. and/or serious damage to this unit and/or users. ・ If the unit is placed too close to the radio, interference to AM/FM reception may result Connect to line input/AUX input on your mixer/pre-amp. Connection To Input LINE2 LINE1 QFO REAR PANEL MODEL NO. QFO 100V 50/60Hz 15W MADE IN CHINA SERIAL NO. LINE MASTER LINE MASTER OUT LINE IN... -
Page 12: Adjustment
All manuals and user guides at all-guides.com ADJUSTMENT NOTE Be careful not to touch your finger to the stylus tip during the adjustment. Adjustment of Horizontal Zero(0) Balance ①Install the cartridge, headshell and balance weight to the Dynamic Stylus Pressure Dynamic Stylus Pressure tonearm. Adjustment knob Adjustment knob ②Adjust the dynamic stylus pressure knob ob the tonearm to Zero. ③Carefully release the tone arm from the tone arm clamp. ④Turn the balance weight clockwise or counterclockwise until balanced horizontally. ... -
Page 13: Operation Of Record
All manuals and user guides at all-guides.com OPERATION OF RECORD ①Place a record on the slip mat. POWER SWITCH ②Turn power switch to "ON" position. ③Remove stylus protector if applicable. ④Select the input select switch to "phono". ⑤Select appropriate rotation speed. (33/45rpm) ⑥Push Start/Stop Switch to start rotation. ⑦Carefully place tonearm on the record. ⑧Adjust the each level volume. ⑨Replace tonearm to rest position after play has finished. POWER MASTER LEVEL ⑩Press Start/Stop Switch to stop rotation. TRIM ⑪Turn power switch to "OFF" position. MEMO -12dB +12dB If you select "PHONO" for both program channels, reproduced sound of record is assigned to each channel. For example, if you squeeze 図a EQ of PGM1 and fix EQ of PGM ... -
Page 14: Exchange The Fader Unit
When you change to new fader unit, please fix the buffer rubber properly. BRACKET FADER VOLUME 【Instructions for cross fader CF-CPV replacement】 ①Unscrew the two screws on the ②Set the change switch of the CF- ③Connect the QFO bracket to the CF-PCV panel and volume as it is PCV to PMC CF-PCV fader volume shown below NOTE CF-PCV has to types of connectors ... -
Page 15: How To Attach Vestax Insulater And Vestax Qfo Hook
When the machine is placed horizontaly to suppress howling under high volume use, attach VESTAX insulater(not included) on 4 sections of the bottom of the body as shown below. How to attach QFO hook In use of the QFO strapped around shoulder or hip, attach VESTAX QFO hook(not included) to the 2 sections of the bottom of the body as shown below. -15 -... -
Page 16: Specification
-10dBv 10kΩ OUTPUT NOMINAL OUTPUT LEVEL IMPEDANCE MASTER -10dBv 220Ω PHONES 58mW MAX(@47Ω) ≧8Ω FREQUENCY RESPONSE 25Hz〜25kHz CROSSTALK ≧100dB THD ＜0.01％ S/N RATIO ≧75dB OTHER DIMENSIONS （W×H×D） 455×130×524(mm) WEIGHT 7.0kg JUL.2004 QFOE○ Vestax Corporation...