Siemens RDG100 Basic Documentation page 51

Name
Expert level
P52 Fan operation
P53 Fan speed
P54 Fan overrun time
(only when electric heater is used)
P55 Switching point fan speed high
P55 ECM fan max. output
P56 Switching point fan speed medium
P56 ECM fan min. output
P57 Switching point fan speed low
P57 ECM: Switching point fan
P58 Fan start booster
P59 Fan min. on time
P60 Fan kick interval in Comfort mode
(time until next kick)
P61 Fan kick interval in Economy mode
(time until next kick)
P62 Clean filter reminder running time
P65 Protection heating setpoint
P66 Protection cooling setpoint
P67 Fan start delay in 2P control
P68 Extension Comfort period
P69 Temporary setpoint Comfort mode
(see also Comfort setpoint P08)
P70 Infrared receiver
P71 Reload factory settings
Name
Diagnostics and test
d01 Application type
d02 X1 status
d03 X2 status
d04 D1 status
d05 Test mode for checking
actuator direction Y1/Y2
(press left button to escape)
d06 Test mode for checking
actuator direction Y3/Y4
(press left button to escape)
d07 Software version ***)
 Parameter available
 Parameter not available
*) If input is parameterized as analog or set to "0": "Err" is displayed when input is out of range (0...49 °C), open or shorted.
**) Thermostats with SW < 7.2 / device index < E: Factory setting = 0
***) RDG100T/H and thermostats with SW 7.2 and higher / device index E
Siemens
Building Technologies
Factory Range
setting
1 0 = disabled
1 = enabled
2 = heating only
3 = cooling only
3-speed 1 = 1-speed
2 = 3-speed
60 s 0...360 s
100% 80..100%
ECM: 80% ECM: fan min...100%
65% 30...75%
ECM: 30% ECM: 0%...fan max.
10% 1...15%
ECM:10% ECM: 0..100%
ON ON: Enabled
OFF: Disabled
2 min. 1...6 min
OFF **) 0...89 min, OFF
OFF 0...359 min, OFF
Off (0) OFF, 100...9900 hours
8 °C OFF, 5...W Cool Prot;
(W Cool Prot = 40 °C max.)
OFF OFF, W Heat Prot...40;
(W Heat Prot = 5 °C min.)
0 s 0...180 s
OFF OFF; 15...360 min
OFF OFF = disabled
ON = enabled
ON OFF = disabled
ON = enabled
OFF OFF = disabled
ON = reload start
Factory Range
setting
Diagnostics 0 = (no application)
1 = 2-pipe
2 = 2-pipe with electric heater
3 = 2-pipe with radiator
4 = 4-pipe
5 = 2 stage heating or cooling
6 = 4-pipe with electric heater
Diagnostics 0 = not activated (for DI)
1 = Activated (DI)
0...49 °C = Curr. temp. value (for AI)
Err
00
100
Diagnostics 0 = not activated (for DI)
1 = Activated (DI)
0...49 °C = Curr. temp. value (for AI)
Err
00
100
Diagnostics 0 = not activated (for DI)
1 = Activated (DI)
00
100
--- "---" = no signal at outputs Y1 and Y2
OPE = output Y1 forced opening
CLO = output Y2 forced closing
--- "---" = no signal at outputs Y3 and Y4
OPE = output Y3 forced opening
CLO = output Y4 forced closing
---
Ux.xx is displayed
RDG100, RDG100T, RDG110, RDG140, RDG160
Functions
     
     x
      P52, Appl
     x
x
     x
x
     x
x
     x
      P52
      P52
      P52
      P52
     
     
    x
     
     
x
     
     
     
*)
= H/C input closed
= H/C input open
     
*)
= H/C input closed
= H/C input open
     
= H/C input closed
= H/C input open
   x
   x
     
Basic Documentation
P52
P52
x x x x  P52
P52
 P52
x x x x
P52
x x x x  P52
P52
x
P52,
P46, P47
  x
x x
x x
P46
x x
P47
51 / 66
CE1P3181en
14 Dec 2011









