Canon imageCLASS MF8380Cdw Starter Manual page 28

Installation Requirements
• A location with sufficient space
• A location with good ventilation
• A location with a flat, even surface
• A location able to fully support the weight of the machine
IMPORTANT
Do not install the machine in the following locations, as this may result in
damage to the machine .
• A location subject to dramatic changes in temperature or humidity
• A location subject to condensation
• A poorly ventilated location
(If you use the machine for a long time or to perform a large amount of printing
in a poorly ventilated room, the ozone or other odors generated by the machine
may create an uncomfortable working environment. In addition, chemical
particles are dispersed during printing; therefore, it is important to provide
adequate ventilation.)
• A location near equipment that generates magnetic or electromagnetic waves
• A laboratory or location where chemical reactions occur
• A location exposed to salt air, corrosive gases, or toxic gases
• A location, such as on a carpet or mat, that may warp from the weight of the
machine or where the machine is liable to sink.
Notes on wireless LAN
• This product is designed for indoor use at a distance of 50 m or less from an
access point (the distance may vary depending on the communication speed or
environmental conditions). Keep it at an appropriate distance.
• Check whether or not anything is blocking communication. The signal may be
degraded when passing through walls or floors. Install accordingly.
• Radio wave interference may occur if any radio wave emitting equipment (i.e.
microwave oven) is located near the product and its radio waves are in the same
frequency band as the radio waves used by the wireless LAN. Keep the product as
far as possible from sources of radio wave interference.
Maintenance and Inspections
IMPORTANT
• Follow the instructions in the caution label attached to this machine.
• Avoid shaking or applying a shock to this machine.
• To prevent a paper jam, do not turn the power ON/OFF, open/close the operation
panel or rear cover, and load/unload paper in the middle of printing operation.
• Be sure to remove the toner cartridge from the machine when transporting the
machine to a distance.
• To avoid exposing the toner cartridge to light, place it in the protective bag
included with this machine or wrap it in a thick cloth.
• Clean this machine regularly. If this machine becomes dusty, it may operate
improperly.
• Use a modular cable of 3 m or shorter in length.
• Depending on your locale or your telephone connection, you may be unable to
perform data communication. In this case, contact your local authorized Canon
dealer or the Canon help line.
• The repairing parts and toner cartridges for the machine will be available
for at least seven (7) years after production of this machine model has been
discontinued.
Contacting Service Center
When you have a problem with your machine and you cannot solve it, even if you
refer to the manuals or online help, please contact your local authorized Canon
dealer from whom you purchased the equipment (if under warranty), or with whom
you have a servicing contact.
Legal Notices
Model Name
MF8380Cdw (F157902)
21
EMC requirements of EC Directive
This equipment conforms with the essential EMC requirements of EC Directive. We
declare that this product conforms with the EMC requirements of EC Directive at
nominal mains input 230 V, 50 Hz although the rated input of the product is 220 to
240 V, 50/60 Hz. Use of shielded cable is necessary to comply with the technical EMC
requirements of EC Directive.
International ENERGY STAR Program
As an ENERGY STAR
this product meets the ENERGY STAR Program for energy
efficiency.
The International ENERGY STAR Office Equipment Program is an
international program that promotes energy saving through the
use of computers and other office equipment.
The program backs the development and dissemination
of products with functions that effectively reduce energy
consumption. It is an open system in which business proprietors
can participate voluntarily.
The targeted products are office equipment, such as computers,
displays, printers, facsimiles, and copiers. The standards and
logos are uniform among participating nations.
IPv6 Ready Logo
The protocol stack included in this machine has obtained the
IPv6 Ready Logo Phase-1 established by the IPv6 Forum.
Laser Safety Information
Laser radiation could be hazardous to the human body. For this reason, laser
radiation emitted inside this equipment is hermetically sealed within the protective
housing and external cover. No radiation can leak from the machine in the normal
operation of the product by the user.
This machine is classified as a Class 1 Laser Product under IEC 60825-1: 2007,
EN60825-1: 2007.
220 to 240 V Model
The label shown below is attached to the laser scan unit on the machine.
This machine has been classified under IEC 60825-1: 2007, EN60825-1: 2007 and
conforms to the following classes:
CLASS 1 LASER PRODUCT
LASER KLASSE 1
APPAREIL À LASER DE CLASSE 1
APPARECCHIO LASER DI CLASSE 1
PRODUCTO LÁSER DE CLASE 1
APARELHO A LASER DE CLASSE 1
LUOKAN 1 LASER-TUOTE
LASERPRODUKT KLASS 1
CAUTION
Use of controls, adjustments, or performance of procedures other than those
specified in the manuals for the machine may result in hazardous radiation exposure.
Partner, Canon Inc. has determined that
®