Subscribe to Our Youtube Channel
Related Manuals for Shark CD-2324
Summary of Contents for Shark CD-2324
- Page 1 Model: Cd operating instruction and parts manual ■ Cd-2323 ■ Cd-2324 For the sHarK dealer nearest you visit our website at www.shark-pw.com 97-726...
-
Page 3: Table Of Contents
CoNTeNTS important safety information ..............4-5 component identification ................. 6 assembly instructions ................7 operating instructions................8-9 applying detergent and general operating techniques ......10 shut down and clean-up ..............11 storage ....................11 troubleshooting ................12-1 preventative maintenance ..............14 oil change record ................14 Hose and spray gun assembly ............. -
Page 4: Important Safety Information
INTRodUCTIoN & IMpoRTaNT SafeTy INfoRMaTIoN thank you for purchasing this pressure Washer. WARNING: Risk of asphyxiation. WaRNINg Use this product only in a well We reserve the right to make changes at any time ventilated area. without incurring any obligation. 5. -
Page 5: Important Safety Information
IMpoRTaNT SafeTy INfoRMaTIoN WARNING: Flammable liquids 1. never make adjustments on machine while in op- WaRNINg eration. can create fumes which can ig- nite, causing property damage 14. Be certain all quick coupler fittings are secured or severe injury. before using pressure washer. WARNING: Risk of explosion WARNING: Protect machine from WaRNINg... -
Page 6: Component Identification
CoMpoNeNT IdeNTIfICaTIoN engine Unloader pump Inlet Water detergent bucket (Not Included) Water Supply Inlet hose Connection (Not Included) quick detergent Coupler Spray gun hose Wand high pressure hose high pressure Nozzle Trigger Soap Nozzle Swivel Connector high pressure hose — connect one end to water Straight Through Wand —... -
Page 7: Assembly Instructions
aSSeMbly INSTRUCTIoNS Spray pressure Nozzle Safety Wand Nozzle extension latch Coupler Spray gun/ Wand high pressure hose STep 1: attach the high STep 2: attach nozzle extension to spray STep 3: pull the spring-loaded pressure hose to the spray gun/wand. tighten both by hand. collar of the wand coupler back gun using teflon tape on to insert your choice of pressure... -
Page 8: Operating Instructions
opeRaTINg INSTRUCTIoNS Stick oil dipstick STep 1: check engine oil level. oil level should be level with the bottom STep 2: remove shipping cap and of the oil filler neck. Be sure the machine is level when checking the oil install oil dipstick. - Page 9 opeRaTINg INSTRUCTIoNS on-off Switch STep 8: on Honda engines, turn the engine switch STep 9: pull the starter grip. if the engine fails to start to "on" position. after 2 pulls, squeeze the trigger gun to release pres- sure and repeat step. return starter gently. after the on Briggs engines, move the throttle lever to "Fast"...
-
Page 10: Applying Detergent And General Operating Techniques
deTeRgeNTS aNd geNeRal opeRaTINg TeChNIqUeS WARNING: Some detergents pump protector engages and cools the pump by dis- WaRNINg charging the warm water onto the ground. this thermal may be harmful if inhaled or in- device prevents internal damage to the pump. gested, causing severe nausea, fainting or poisoning. -
Page 11: Shut Down And Clean-Up
ShUTTINg doWN aNd CleaN-Up on-off Switch STep 1: remove detergent suc- STep 3: turn off water STep 2: move the throttle to stop the tion tube from container and insert supply. engine (Briggs engine). turn off the into one gallon of fresh water. slide engine (Honda engines). -
Page 12: Troubleshooting
TRoUbleShooTINg pRobleM poSSIble CaUSe SolUTIoN loW opeRaTINg insufficient water supply use larger garden hose; clean filter washer at pReSSURe water inlet. old, worn or incorrect spray nozzle match nozzle number to machine and/or replace with new nozzle. plumbing or hose leak check plumbing system for leaks. - Page 13 TRoUbleShooTINg pRobleM poSSIble CaUSe SolUTIoN pReSeNCe of Water sprayed at machine change oil. direct spray away from machine. WaTeR IN pUMp oIl High humidity in air check and change oil twice as often. (model 224 only) piston packing worn. oil seal worn check and replace if necessary. eNgINe STRaINS engine governor misadjusted readjust governor on engine.
-
Page 14: Preventative Maintenance
pReveNTaTIve MaINTeNaNCe this pressure washer was produced with the best available materials and quality craftsmanship. However, you as the owner have certain responsibilities for the correct care of the equipment. attention to regular preventative maintenance procedures will assist in preserving the performance of your equipment. contact your dealer for maintenance. -
Page 15: Hose And Spray Gun Assembly
hoSe & SpRay gUN aSSeMbly Model 232336 pressure Nozzle brass Soap Nozzle hoSe & SpRay gUN aSSeMbly paRTS lIST ITeM paRT No. deSCRIpTIoN ITeM paRT No. deSCRIpTIoN 2-2002 coupler, /8" Female (224) 4-011106 Wand, straight 2-0121 ▲ Quick coupler o-ring 2-2000 coupler, 1/4"... -
Page 16: Exploded View
exploded vIeW Model 2324 MODE D' EMPLOI ATTENTION 11-0350F (Reversed view) Model 232336 cd 97-726 • rev. 7/07... -
Page 17: Exploded View Parts List
exploded vIeW paRTS lIST ITeM paRT No. deSCRIpTIoN ITeM paRT No. deSCRIpTIoN 5-0101 engine, Honda gc1601QHa, 2-2007 nipple, /8" x /8" npt st male 5 Hp (226) (224) 5-0104 engine, Honda, gX160K1QX2, 11-050F label, French Warning 5.5 Hp (224) 90-1005 Bolt, 5/16"-24 x /4", nF, HH 5-1451 pump, sg250g... -
Page 18: Sg Series Pump Exploded View & Parts List
Sg SeRIeS pUMp exploded vIeW 5-1451 Sg2530g ToRqUe SpeCS item # Ft.-lbs Sg SeRIeS pUMp paRTS lIST ITeM paRT No. deSCRIpTIoN ITeM paRT No. deSCRIpTIoN 70-020292 crankcase 70-140001 Washer 70-06006 copper Washer /8" see Kit Below plunger oil seal 70-160117 Brass plug /8"... - Page 19 Sg SeRIeS pUMp paRTS lIST ITeM paRT No. deSCRIpTIoN 70-000105 crankshaft seal 70-00211 plunger nut see Kit Below plunger, 15mm 70-140027 copper spacer 70-06010 o-ring Ø1.78x5.28 70-00091 teflon ring 70-00020 plunger rod 70-150204 connecting rod pin 70-010008 connecting rod 70-140102 spring Washer 70-18012 connecting rod screw...
-
Page 20: Axd Pump Exploded View & Parts List
pUMp exploded vIeW aNd paRTS lIST 9.120-032.0 ITeM paRT # deSCRIpTIoN ITeM paRT # deSCRIpTIoN 6.62-851.0 o-ring, d. 4 x 2 nBr 90 9.175-007.0 unloader assembly 9-154-06.0 m18 pipe plug 6.62-84.0 o-ring seal, 9.0 x 1.5 6.62-480.0 o-ring seal, 12.42 x 1.78 4.769-04.0 nozzle insert only for replacement... - Page 21 pUMp exploded vIeW paRTS lIST 9.120-032.0 pISToN vIeW ITeM paRT # deSCRIpTIoN 9.19-19.0 spare parts list set 1 6.65-9.0 grooved ring 12 x 20 x 4/6 9.14-016.0 spacer, oil seal and seal Housing 6.6-058.0 grooved ring 9.155-011.0 Housing, low pressure seal 6.62-8.0 o-ring seal, 21.5 x 1.78 9.177-10.0...
-
Page 22: Vba5 Unloader Exploded View & Parts List
vba35 UNloadeR exploded vIeW paRTS lIST #5-3329, vba35 lg/ld/le (240378) 6.6 gpM @ 3500 pSI vba35 UNloadeR exploded vIeW paRTS lIST ITeM paRT # deSCRIpTIoN kIT qTy ITeM paRT # deSCRIpTIoN kIT qTy 70-020444 Body Valve 70-110207 poppet 70-020452 Body Valve 70-140802 seal Washer /8 70-060141... - Page 23 PARTICULAR PURPOSE. SHARK does not authorize any other party, including authorized Dealers, to make any representa- tion or promise on behalf of SHARK, or to modify the terms, conditions, or limitations in any way. It is the buyer’s responsibility to ensure that the installation and use of SHARK products conforms to local codes. While SHARK attempts to assure that its products meet national codes, it cannot be responsible for how the customer chooses to use or install the product.
- Page 24 Form #97-726 • revised 7/07 • printed in u.s.a.
Need help?
Do you have a question about the CD-2324 and is the answer not in the manual?
Questions and answers