Wiring Skyroute Max To A Dsc Control Panel; Supervised Power Supply Connection; Enroll Skyroute Max Onto The System - DSC SKYROUTE max Quick Install Manual

6.14 Wiring Skyroute max
Control Panel
• Remove the circular knockout in the top left corner of
the control panel cabinet. Mount the Skyroute max unit
in its place.
• Secure the Skyroute max module to the cabinet using
the supplied screws.
• Attach the Skyroute max antenna to the unit.
• Disconnect and remove the AC and battery power from the
control panel. Wire the red, black, yellow and green wires
from the panel Keybus to the corresponding RED, BLK, YEL
and GRN terminals on the Skyroute max transceiver.
• Wire a normally closed tamper switch between the COM
and TAM terminals of the Skyroute max module. If a
tamper switch is not going to be used, place a jumper
wire between the COM and TAM terminals.
• Wire the BELL+ terminal of the panel to the BELL IN
terminal of the Skyroute max unit. The wire run must not
exceed 150 ft. / 45.5 m.
• Wire the BELL- terminal of the panel to the negative (-)
terminal of the bell/siren.
• Wire the BELL+/SIREN+ terminal of the panel to the
BELL OUT terminal of the Skyroute max transceiver.
• Apply AC and DC power to the control panel. Power up
both the Skyroute max module and the panel.
• Do the programming if it is required.
• Call the Connect 24 VRU (Voice Response Unit) to
activate your Skyroute max account.
NOTE: If a bell or sir NOTE: If a bell or sir NOTE: If a bell or sir NOTE: If a bell or sir NOTE: If a bell or siren is not going to be used in the system, en is not going to be used in the system, en is not going to be used in the system, en is not going to be used in the system, en is not going to be used in the system,
wir wir e the BELL/SIREN terminals on the panel with a 1000 e the BELL/SIREN terminals on the panel with a 1000
wir wir wire the BELL/SIREN terminals on the panel with a 1000 e the BELL/SIREN terminals on the panel with a 1000 e the BELL/SIREN terminals on the panel with a 1000
Ohm r Ohm r esistor esistor . Then wir . Then wir e only the BELL+ terminal of the panel e only the BELL+ terminal of the panel
Ohm resistor Ohm r Ohm r esistor esistor. Then wir . Then wir . Then wire only the BELL+ terminal of the panel e only the BELL+ terminal of the panel e only the BELL+ terminal of the panel
to the BELL IN terminal of the Skyroute max module. to the BELL IN terminal of the Sk to the BELL IN terminal of the Sk
to the BELL IN terminal of the Sk to the BELL IN terminal of the Sk

6.15 Supervised Power Supply Connection

Power Requirements
The PC4204 requires a 16V, 40 VA transformer and a 12V, 7
Ah battery.
NOTE: If a battery is not connected to the PC4204, and NOTE: If a battery is not connected to the PC4204, and
NOTE: If a battery is not connected to the PC4204, and NOTE: If a battery is not connected to the PC4204, and NOTE: If a battery is not connected to the PC4204, and
expansion trouble and a r expansion trouble and a r
expansion trouble and a restoral will be generated every expansion trouble and a r expansion trouble and a r
time a signal is transmitted. time a signal is transmitted. time a signal is transmitted.
time a signal is transmitted. time a signal is transmitted.
max max max to a DSC/Partner max
yroute max module. yroute max module. yroute max module.
yroute max module.
estoral will be generated every estoral will be generated every
estoral will be generated every estoral will be generated every
Connections
• The Combus from the panel is connected to both the
PC4204 and the Skyroute max transceiver.
• A wire is connected from the AUX terminal on the
PC4204 to the BELL IN of the Skyroute max transceiver.
• A jumper or a normally closed switch is required between
the TAM and the COM terminals on the Skyroute max
transceiver.
• A jumper or a normally closed switch is required
between the TAM and the BLK terminals for the tamper
of the PC4204.
• Wire the positive lead of the device to the AUX+ terminal.
NOTES: for secur NOTES: for secur NOTES: for secur NOTES: for secure installation a tamper switch must be NOTES: for secur e installation a tamper switch must be e installation a tamper switch must be e installation a tamper switch must be e installation a tamper switch must be
installed on the Sk installed on the Sk yroute max module. yroute max module.
installed on the Skyroute max module. installed on the Sk installed on the Sk yroute max module. yroute max module.
Using PC4204 power supply module for this configuration Using PC4204 power supply module for this configuration Using PC4204 power supply module for this configuration
Using PC4204 power supply module for this configuration Using PC4204 power supply module for this configuration
is not UL Listed. A UL1481 Listed power supply 12V/1.5A is not UL Listed. A UL1481 Listed power supply 12V/1.5A is not UL Listed. A UL1481 Listed power supply 12V/1.5A is not UL Listed. A UL1481 Listed power supply 12V/1.5A is not UL Listed. A UL1481 Listed power supply 12V/1.5A
(e.g. . . . . , , , , , PS4350) must be used for UL Listed applications. (e.g (e.g (e.g (e.g PS4350) must be used for UL Listed applications. PS4350) must be used for UL Listed applications. PS4350) must be used for UL Listed applications. PS4350) must be used for UL Listed applications.
6.16 Enroll Skyroute max
Once all the wiring is complete, you must enroll the module:
• Enter installer's programming by pressing [*] [8]
[Installer's Code]
• Scroll to "Module Hardware" and press the [*] key.
• Scroll to "Enroll Module" and press the [*] key.
• Scroll through the different modules until "Alternate
Comms" is displayed. Press the [*] key.
• The message "Create Tamper on Desired Unit" will be
displayed. To create the required tamper, secure the
tamper zone on the module and then open it. The transition
from secure to violated enrolls the module. After this is
done, the keypad will display the module number and
confirm enrollment "Alternate Comms Mod 01 Enrolled".
For more information regarding module enrollment, see the
control panel Installation Manual .
10 10 10 10 10
max onto the system max max max