Vortice Caldomi Instruction Booklet page 10

414 impa CaldomiC:Impag414.qxd
4
!
Caution:
• Do not make modifications of any kind to this
appliance.
• Take particular care if the appliance is used in
unsupervised environments.
• Do not expose this appliance to the weather (rain,
sun, etc.).
• Regularly inspect the appliance for visible
imperfections. If the appliance does not function
correctly, contact Vortice* immediately.
• Should the appliance be dropped or suffer a heavy
blow, have it checked immediately by Vortice*.
• If the appliance does not function correctly or
develops a fault, turn it off, disconnect the plug from
the power supply and contact Vortice* immediately.
Ensure that only genuine original Vortice spares are
used for any repairs.
• Never position the appliance directly under a power
socket.
• The appliance must be properly connected to the
power supply in compliance with applicable
standards; it does not require to be earthed, as it is
double-insulated. If in doubt, request a qualified
electrician to perform a thorough check.
• The electrical power supply/socket to which the
appliance is to be connected must be able to
provide the maximum electrical power required by
the appliance.
• If the power socket is of a different type to the plug
fitted on the appliance, call a qualified technician
and ask him to replace it with a socket of the right
type. Do your best to avoid the use of adapters,
multiple sockets and/or extension leads;
if necessary, first make sure that they comply with
current safety regulations and check that the
maximum allowed power is compatible with the
values on the appliance's rating plate.
Any extension leads must be as short as possible,
to prevent them from overheating and triggering
the thermal cut-out devices.
• Do not pull on the power cable, do not place it near
heat sources and always uncoil it completely to
prevent dangerous overheating. If the cable or the
power plug are damaged, take the appliance to
Vortice for replacement.
• Do not cover, squeeze or place the power cable
near hot objects to avoid any risk of overheating or
10
20/07/07
This symbol indicates precautions that must be taken to avoid damage to the appliance
8.55 Pagina 10
5
damage; at the same time, make sure it is placed
so that it does not create an obstacle.
• Do not coil the power cable on the appliance and
do not operate the appliance with the cable coiled.
• To prevent hazardous overheating, it is
recommended to uncoil the power cable entirely
and use the appliance as indicated in the
instructions.
• During operation, the power socket must be easily
accessible to enable quickly unplugging from the
mains.
• A limited increase in temperature in the power
cable and plug during use of the appliance is to be
considered normal; however, if the phenomenon
increases to the point that they become too hot to
touch or start to deform, contact Vortice*
immediately.
• Never place the power cable in front of the heating
element.
• Always keep the appliance in an upright position.
• When the appliance is not being used, turn it off
and disconnect the plug from the power supply.
• Before cleaning the appliance in any way, turn it off
and disconnect the plug from the power supply.
• Do not immerse the appliance in water.
• Do not insert anything into the appliance.
• Keep the appliance's intake and outlet grilles free
and uncovered.
• Do not cover the appliance, as this may result in
dangerous overheating.
• This appliance is not suited for rooms used in
zootechnics.
N.B. The appliance is equipped with safety
devices (reset manually) which cuts out if the
appliance itself starts to overheat, so as to avoid
any risk of damage. In these cases, disconnect
the plug, leave the appliance to cool for
approximately 10 min. and lastly plug it back into
the power socket. To avoid the harmful effects of
continual switching on and off, it is necessary to
remove the cause of the trouble (grilles
obstructed, appliance tipped over, fan jammed,
etc).
*(or an authorized Vortice dealer if you are outside
the UK-Ireland territory)