Related Manuals for Tektronix OM2012
Summary of Contents for Tektronix OM2012
- Page 1 OM2012 nLaser Tunable C-, L-Band Laser Source Installation and Safety Instructions 071-3154-03...
- Page 3 OM2012 nLaser Tunable C-, L-Band Laser Source Installation and Safety Instructions www.tek.com 071-3154-03...
- Page 4 Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material.
- Page 5 Tektronix, with shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.
-
Page 7: Table Of Contents
Operate the instrument ..................Equipment setup ....................Controls and connectors ................... Front panel...................... Rear panel ...................... Cleaning and maintenance..................Cleaning ......................Maintenance ....................Compliance information ..................EMC compliance ..................... Safety compliance .................... Environmental considerations ................OM2012 Installation and Safety Instructions... -
Page 8: Important Safety Information
Do not disable the power cord grounding connection. Power disconnect. The power cord disconnects the product from the power source. See instructions for the location. Do not position the equipment so that it OM2012 Installation and Safety Instructions... - Page 9 Provide proper ventilation. Refer to the installation instructions in the manual for details on installing the product so it has proper ventilation. Slots and openings are provided for ventilation and should never be covered or otherwise obstructed. Do not push objects into any of the openings. OM2012 Installation and Safety Instructions...
-
Page 10: Service Safety Summary
Disconnect power, remove battery (if applicable), and disconnect test leads before removing protective panels, soldering, or replacing components. Verify safety after repair. Always recheck ground continuity and mains dielectric strength after performing a repair. OM2012 Installation and Safety Instructions... -
Page 11: Terms In This Manual
find out the nature of the potential hazards and any actions which have to be taken to avoid them. (This symbol may also be used to refer the user to ratings in the manual.) The following symbol(s) may appear on the product: OM2012 Installation and Safety Instructions... -
Page 12: Safety Related Front Panel Labels
Important safety information Safety related front panel labels Item Description Indicates the location of laser apertures Safety related rear panel labels OM2012 Installation and Safety Instructions... - Page 13 Important safety information Item Description Instrument model and serial number label Fuse safety information COMPLIES WITH 21CFR1040.10 EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE NO. 50, DATED JUNE 24, 2007 OM2012 Installation and Safety Instructions...
- Page 14 Important safety information viii OM2012 Installation and Safety Instructions...
-
Page 15: Preface
Coherent Receiver Calibration Source. Product description The OM2012 provides two tunable C-band or L-band laser sources for use in laboratory or industrial facilities for a variety of fiber optic system applications. The OM2012 is controlled using software over an Ethernet connection. - Page 16 Preface OM2012 Installation and Safety Instructions...
-
Page 17: Operating Requirements
Environment requirements CAUTION. Damage to the instrument can occur if this instrument is powered on at temperatures outside the specified temperature range. Table 1: OM2012 environmental requirements Parameter Description Temperature Operating +10 °C to +35 °C (+50 °F to +95 °F) CAUTION. -
Page 18: Power Requirements
Tektronix. PC requirements The OM2012 product is not a stand-alone instrument; it requires Laser Receiver Control Panel (LRCP) software or OM1106 Optical Modulation Analysis software installed on a PC or oscilloscope running Microsoft Windows 7 operating system, which in turn is connected to the instrument with an Ethernet cable (directly from PC or through a network). -
Page 19: Installation
See the included packing list. Contact your local Tektronix Field Office or representative if there is a problem with your instrument or if your shipment is incomplete. Power-related controls and connectors 1. -
Page 20: Connect The Power Cable
Push the front panel Power button to power on the instrument. 4. If the fan still does not work, repeat the power off sequence, disconnect the AC power cord, and contact your local Tektronix Field Office or representative for help. -
Page 21: Operate The Instrument
Installation Operate the instrument The OM2012 product is not a stand-alone instrument; it requires Laser Receiver Control Panel (LRCP) software or OM1106 Optical Modulation Analysis software installed on a PC or oscilloscope running Microsoft Windows 7 operating system, which in turn is connected to the instrument with an Ethernet cable (directly from PC or through a network). - Page 22 Installation OM2012 Installation and Safety Instructions...
-
Page 23: Controls And Connectors
Controls and connectors Front panel 1. On/Off standby switch 2. Laser 1 output (with LED indicator) 3. Laser 2 output (with LED indicator) Rear panel 1. Main power switch 2. Fuse holder OM2012 Installation and Safety Instructions... - Page 24 Controls and connectors 3. Power cable connector 4. BNC shorting plug for optional laser remote interlock connector 5. 10/100/1000 Ethernet port OM2012 Installation and Safety Instructions...
-
Page 25: Cleaning And Maintenance
Maintenance Never remove the instrument cover. There are no user-serviceable components or subsystems within the OM2012. Attempting any internal repairs will void your warranty. If it becomes necessary to replace the fuse (on the rear panel), use a 5X20 mm “slo-blo”... - Page 26 Cleaning and maintenance OM2012 Installation and Safety Instructions...
-
Page 27: Compliance Information
Complies with the EMC provision of the Radiocommunications Act per the following standard, in accordance with ACMA: declaration of conformity – EMC CISPR 11 Australia / New Zealand contact. Baker & McKenzie Level 27, AMP Centre 50 Bridge Street Sydney NSW 2000, Australia OM2012 Installation and Safety Instructions... -
Page 28: Safety Compliance
(as defined in IEC 61010-1). IP rating IP20 (as defined in IEC 60529). Mains overvoltage The mains power supply circuit for this product is rated for overvoltage category II (as defined in IEC 61010-1). category rating OM2012 Installation and Safety Instructions... -
Page 29: Environmental Considerations
Restriction of hazardous This product is classified as an industrial monitoring and control instrument, and is not required to comply with the substance restrictions of the recast RoHS substances Directive 2011/65/EU until July 22, 2017. OM2012 Installation and Safety Instructions...
Need help?
Do you have a question about the OM2012 and is the answer not in the manual?
Questions and answers