SpeakerCraft SC-BT-10 Manual
SpeakerCraft SC-BT-10 Manual

SpeakerCraft SC-BT-10 Manual

All-weather landscape burial subwoofers

Advertisement

Quick Links

ALL-WEATHER LANDSCAPE BURIAL SUBWOOFERS

Burial Subwoofers: 10" & 12" (250mm & 300mm)
CONTENTS
10" Burial Subwoofer:
ƒ (1) Burial Subwoofer with Direct Burial Cable
Attached
ƒ (2) Silicone-Filled Wire Connectors
12" Burial Subwoofer Box 1 of 2:
ƒ Burial Subwoofer with Direct Burial Cable
Attached
ƒ (2) Silicone-Filled Wire Connectors
12" Burial Subwoofer Box 2 of 2:
ƒ (1) Burial Subwoofer Canopy Assembly
ƒ (1) Port Tube with Compression Clamps
REQUIRED TOOLS:
ƒ Wire Strippers
ƒ Digging Tools as needed for the
soil type
ƒ Measuring Tape
ƒ Slotted Screwdriver
ƒ Pea Gravel
(optional, recommended as a drainage base for
high clay content soils)
AMPLIFICATION GUIDELINES:
Crown CDi 2|600 Amplifier
These Subwoofers are 8Ω and are optimized for
use with the Crown CDi 2|600 amplifier which is
preprogrammed with customized DSP settings
for a variety of different speaker/ subwoofer
installations. Please refer to the addendum
included in the Crown CDi 2|600 for additional
instructions.
Other Amplifiers
These Subwoofers are 8Ω and are compatible
with low impedance amplifiers with low pass
filters. The minimum recommended power
per channel in low impedance mode is 100W/
Channel. A low pass filter that slightly overlaps
the high pass filter of the associated satellite
speakers is recommended for proper blending.
WARNING:
ƒ PLEASE READ AND FOLLOW ALL
INSTRUCTIONS BEFORE BEGINNING YOUR
INSTALLATION.
ƒ POTENTIAL HAZARDS SUCH AS ELECTRICAL,
GAS, BURIED CABLES, PLUMBING OR OTHER
OBSTACLES SHOULD BE VERIFIED AND
CHECKED BEFORE INSTALLING GROUND
STAKES AND/OR OTHER ACCESSORIES.
ƒ MANY LOCALITIES FORBID DIGGING
WITHOUT PRIOR AUTHORIZATION, SO
CONTACT LOCAL AUTHORITIES BEFORE
INSTALLATION.
SPEAKER CABLE
Burial–rated cable (not included) is strongly
recommended. It is also important to use the
proper speaker cable gauge depending on
the size of your area.
Cable Gauge
18 Gauge
16 Gauge
14 Gauge
12 Gauge
10 Gauge
INSTALLATION
CONSIDERATIONS
Before you start digging a trench:
ƒ Test EACH speaker prior to installation.
ƒ Verify that the proposed area is accessible
and not prone to flooding or standing water.
It is also important to ensure your speakers
cannot be easily damaged, kicked, or hit.
ƒ Take into consideration the overall
landscape/garden design and positioning in
relation to listening area.
1
Distance
Up to 100 ft (30m)
Up to 150 ft (45m)
Up to 200 ft (61m)
Up to 400 ft (122m)
Up to 650 ft (198m)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SC-BT-10 and is the answer not in the manual?

Questions and answers

Summary of Contents for SpeakerCraft SC-BT-10

  • Page 1: Required Tools

    ALL-WEATHER LANDSCAPE BURIAL SUBWOOFERS Burial Subwoofers: 10” & 12” (250mm & 300mm) WARNING: CONTENTS 10” Burial Subwoofer: ƒ PLEASE READ AND FOLLOW ALL INSTRUCTIONS BEFORE BEGINNING YOUR ƒ (1) Burial Subwoofer with Direct Burial Cable INSTALLATION. Attached ƒ (2) Silicone-Filled Wire Connectors ƒ...
  • Page 2 PLANNING THE INSTALL SUBWOOFER 110° 110° 110° 110° 14.37 21.02 533.8 10.63 35.71 15.75 NI-GSBSUB-10 Locate the subwoofer(s) near the landscape satellite speakers for proper blending. NI-GSSUB-12 As a guideline, each subwoofer will provide coverage for between 1500 and 2500 square feet for the 10”...
  • Page 3 12” BURIAL SUBWOOFER HOLE DIMENSIONS The subwoofer cabinet is approximately 16” in diameter and 32” long with the port tube attached. Dig a hole that is at least 24” wide and 40” long so that it is about 4 inches larger than the sub in each direction to allow for the sub to be adjusted side to side.
  • Page 4 Hole Depth 10” BURIAL SUBWOOFER HOLE DIMENSIONS 5-7” Above Ground Level The 10” subwoofer cabinet is approximately 16” in diameter. Dig a hole at least 24” in diameter, leaving about 4 inches of space on all sides of the subwoofer. Dig to a depth of approx. 16”. 40”...
  • Page 5 WIRING & SPEAKER INSTALLATION Mono Setup Using 4-Conductor Burial Cable & Crown Amplifier 10.63 14.37 21.02 533.8 15.75 Black and Red 35.71 White and Green NI-GSBSUB-10 Mono Mono Mono Mono Mono Mono NI-GSSUB-12 Burial Cable Preparation Create a loop approximately 6” Use a wire tie (not included) to in length starting with the first keep the wire loop intact and act as...
  • Page 6 WIRING & SPEAKER INSTALLATION Speaker & Burial Cable Connections Combine and twist (clockwise) the red wires (see diagram) from the amp, speaker, and to the next speaker in the series. Secure these three wires using the provided silicone-filled wire connectors; Repeat procedure for Black wires.
  • Page 7 TEST SYSTEM Connect the wires to your receiver or amplifier after all satellites and subwoofer connections are completed. IMPORTANT: Be sure to not let any stray “+” and “-” strands touch each other. A short circuit could damage your amplifier. Turn your receiver or amplifier ON and test the system with your favorite music.
  • Page 8 LIMITED LIFETIME WARRANTY Core Brands, LLC (“Core Brands”) warrants to the original retail purchaser only that this product will be free of manufacturing defects in material and workmanship for the following periods and subject to the limitations and exclusions set forth below: Limited Lifetime from the date of purchase This warranty is not transferable to subsequent purchasers of the product.

Table of Contents