Honeywell 1000 Series Instruction Sheet page 29

Checking flame current
 The minimum value should be in accordance with specified
value.
 To check flame current connect a DC micro--Ampèremeter
between flame sensing wire and flame sensing rod.
 If flame current is insufficient check that flame sensing rod
is fully enveloped by the flame and that burner is reliable
grounded to the ignition control.
 If there is no sufficient flame current due to phase--phase
mains it is recommended to use an ignition control with the
phase neutral independent operation feature. If this is not
available, it is recommended to use a AT7030A or
AT7030B flame detection transformer. See also instruction
sheet EN1R--9136 for the AT7030 transformer.
WARNING
Short ←A meter during ignition to prevent damage of
the ←A meter in single rod application.
FINAL CHECKOUT
Final checkout of the installation
Set appliance in operation after any adjustment and observe
several complete cycles to ensure that all burner components
function correctly.
 To check flame current connect a DC micro--Ampèremeter
between flame sensing wire and flame sensing rod.
 If flame current is insufficient check that flame sensing rod
is fully enveloped by the flame and that burner is reliable
grounded to ignition control.
 If there is no sufficient flame current due to phase--phase
mains it is recommended to use an ignition control with the
phase--neutral independent operation feature. If this is not
available, it is recommended to use an AT7030A or
AT7030B flame detection transformer. See also instruction
sheet EN1R--9136 for AT7030 transformer.
Housing (degree of protection)
New style housing (see fig. 1.)
Enclosure IP 20 (standard housing)
Use: strain relief set
Enclosure IP40
Use: cover set . . . . . . . . . . . . . . . . . . . . . . . . .
cover set
(flame retardant according to UL94--VO)
cable grommet
Enclosure IP 44 (only applicable for specific O.S. numbers)
Use: cover set . . . . . . . . . . . . . . . . . . . . . . . . .
cover set
(flame retardant according to UL94--VO)
cable grommet
sleeve . . . . . . . . . . . . . . . . . . . . . . . . . . .
gasket . . . . . . . . . . . . . . . . . . . . . . . . . . .
Old style housing (see fig. 2.)
Enclosure IP 20 (standard housing)
Enclosure IP30
Use: strain relief set
cover set (external reset)
cover set (internal reset)
Enclosure IP40
Use: strain relief set
cover set (external reset)
cover set (internal reset)
grommet . . . . . . . . . . . . . . . .
(depending on application and number of cables)
Enclosure IP 44 (on request)
29
. . . . . . . . . . . . . . . . . . . . 45.900.440--001
45.900.431--004
45.900.431 --005
. . . . . . . . . . . . . . . . . . . . 45.900.442 --008
45.900.431--004
45.900.431 --005
. . . . . . . . . . . . . . . . 45.900.442 --008/009
45.900.442--003
45.900.442--011
. . . . . . . . . . . . . . . . . . . . 45.900.440--001
. . . . . . . . . . . 45.900.401--044
. . . . . . . . . . . . 45.900.401--045
. . . . . . . . . . . . . . . . . . . . 45.900.440--001
. . . . . . . . . . . 45.900.401--044
. . . . . . . . . . . . 45.900.401--045
45.900.442 --001 and --002
EN1R- -9161 0006R10- -NE