Attaching The Hose - Black+Decker FSMH1321 Manual

ENGLISH
• Return the handle (8) to the upright position and turn the
steam mop 'OFF'.
• Wait until the steam mop cools down (approximately 5
minutes).
• Place the front of your shoe onto the carpet glider
removal tab and press down firmly.
• Lift the steam mop up and off the carpet glider.
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Attaching the hose and accessories to the
hand held steam cleaner (Fig. G - O)
Warning! Inspect the seal between the connection point on
the hand held steam cleaner (5) and the steam hose (16)
before each use. If the seal malfunctions or is damaged,
please contact your nearest authorised repair agent. Do not
use the appliance.

Attaching the hose

• Press the steam hose release button (16a) on the steam
hose (16).
• Connect the steam hose (16) to the hand held steam
cleaner (5) and release the steam hose release button
(16a) making sure it clicks into place.
Important! Ensure that the steam hose (16) is securely
connected to the hand held steam cleaner (5). If steam
escapes from the joint, the hose is incorrectly fitted. Switch
off, allow the unit to cool then remove and refit the hose.
Attaching accessories (Fig H)
• Align the lugs on the steam nozzle (17) with the
recesses on the accessory.
• Press the accessory onto the steam nozzle (17) and
twist anti-clockwise until the accessory clicks into place.
Important! All accessories, apart from the SteaMitt
which has its own hose and connector (26), must be
attached to the steam hose (16) for use.
Removing the hose and accessories
Warning! The steam hose (16), Steam nozzle (17) and
accessories become hot during use. Allow the unit and all
accessories to cool before attempting to remove.
Removing an accessory
• Twist the accessory clockwise then pull away from the
hose (16).
Removing the hose
• Press the steam hose release button (16a) on the steam
10
(Original instructions)
(25)
TM
hose (16) and pull away from the hand held steam unit.
SteaMitt
TM
Your BLACK+DECKER SteaMitt
TM
sanitising and cleaning tiles, work tops, kitchen surfaces and
bathroom surfaces. This appliance is intended for indoor
household use only.
Attaching the SteaMitt hose to the hand held steam unit
TM
Warning! Inspect the seal between the connection point on
the hand held steam cleaner (5) and the SteaMitt
before each use. If the seal malfunctions or is damaged,
please contact your nearest authorised repair agent. Do not
use the appliance.
• Press the SteaMitt hose release button on the
TM
SteaMittTM hose (26).
• Connect the SteaMitt
TM
cleaner (5) and release the SteaMitt
button making sure it clicks into place.
Important! Ensure that the SteaMitt
connected to the hand held steam cleaner (5).
If steam escapes from the joint, the hose is incorrectly fitted.
Switch off, allow the unit to cool then remove and refit the
hose.
Fitting a cleaning pad to the SteaMitt
(Fig. L)
• Fit the cleaning pad (27) to the SteaMitt
attaching the 'loop' velcro strips (27a) on the upper side
of the cleaning pad, to the 'hook' velcro pads (25a) on the
underside of the SteaMitt
Warning! The SteaMitt should not be used without fitting a
TM
cleaning pad.
Note: The SteaMitt
accommodates 3 types of cleaning
TM
pads of varying thickness. The thinnest can be used for
cleaning 3D forms such as taps etc. The thicker versions can
be used for larger flat areas.
Warning! Always use the SteaMitt
with your hand inside the protective glove.
Warning! Never attempt to use the SteaMitt
externally as shown in figure N. This will result in scalding.
Warning! Avoid using the SteaMitt
shown in figure O.
Warning! Should a problem occur during use, use the quick
release tab to quickly remove the SteaMitt
as shown in figure P.
Warning! Do not use the SteaMitt
windows as damage may be caused by the sudden change
in temperature.
Warning! Never point or direct the mitt at yourself or any
other person.
Note: Variable steam dial is disconnected when the
SteaMitt is fitted and subsequently the flow of steam is
TM
limited.
has been designed for
TM
hose (26)
TM
hose (26) to the hand held steam
hose release
TM
hose (26) is securely
TM
TM
(25) by
TM
(4). Press down firmly.
TM
as shown in figure M,
TM
by gripping it
TM
in tight corners as
TM
from your hand
TM
on cold glass, such as
TM