Removing And Replacing The Covers - HP NetServer LH 3 Installation Road Map

3
Obtain HP Navigator CD-ROM Release History
Before you begin installing your HP NetServer, ensure that you
have the latest version of the software by obtaining the current HP
NetServer Navigator CD-ROM release history. It describes the
latest software updates to each release of the Navigator CD-ROM,
as well as instructions for obtaining the current release.
Call HP's fax system at 1-800-333-1917 (or 1-208-344-4809 from
Fax—
your fax machine), and request document number 6005
http://www.hp.com/netserver/servsup
Internet WWW—
ftp://ftp.hp.com/pub/servers
Internet FTP—
GO HPPC; download 6005.txt from the NetServer library
CompuServe—
4
Connect Monitor, Keyboard, and Mouse
Connect the monitor, keyboard, and
1. Connect cables:
mouse cables and the AC power cord to the appropriate
connectors on the rear of the chassis.
If you have an uninterruptible power supply
2. Connect UPS:
(UPS), refer to the instructions supplied with it. Install and turn
on the UPS.
5
Preparation
1. Boot the HP Navigator CD-ROM:
Press the power-on button on the HP NetServer, and press the
eject button on the CD-ROM drive. Place the HP Navigator CD-
ROM in the drive, and close the drive. Press the Reset button. If
the system fails to restart, follow the instructions on the screen.
When HP Navigator starts, you can set the time and date, and
change the display language.
2. Read the Readme File
Navigator Main Menu. The Readme file contains the latest
information to help you install your HP NetServer.
3. Run Diagnostic Assistant (Optional):
NetServer hardware as shipped, run Diagnostic Assistant from
the HP Navigator CD-ROM. Select "NetServer Utilities" from the
HP Navigator Main Menu, and then select "Diagnostic
Assistant" from the NetServer Utilities menu.
6

Removing and Replacing the Covers

If you are installing accessory cards or mass storage devices,
remove the front bezel and cover 1. If you are installing memory,
remove the front bezel and cover 3.
To install some options, you will need a flat 1/4-inch screwdriver
®
and a T15 TORX driver.
WARNING Before removing cover(s), always disconnect the
power cord and unplug telephone cables.
Disconnect the power cord to avoid exposure to
high energy levels that may cause burns when
parts are short-circuited by metal objects, such as
tools or jewelry. Disconnect telephone cables to
avoid exposure to shock hazard from telephone
ringing voltages.
Note that the power switch does not turn off the
standby power. Disconnect the power cord to turn
off standby power. If the backlight on the LCD
display is on, standby power is on.
Wear a wrist strap and use a static-dissipating work
CAUTION
surface connected to the chassis at all times.
To remove a cover:
1. Turn off the HP NetServer
and telephone cord.
2. Unlock the bezel lock
located on the rear of the HP NetServer.
3. To remove the front bezel,
from the chassis, and then lift the bezel up and off of the chassis.
4. Loosen the thumbscrew
the cover forward, using the handle on the cover, and then lift it
off the chassis.
To replace a cover:
All manuals and user guides at all-guides.com
Turn on the monitor.
Select "Readme File" from the HP
:
To verify the HP
and disconnect the power cord
with the key from the key bag
pull the top of the bezel away
at the front of the cover and pull
You can obtain the release history from one of the HP NetServer
information resources listed here.
To obtain drivers and utilities for the non-HP components of your
system, follow the directions provided by the component or network
operating system (NOS) manufacturer to access the necessary
Internet, BBS, or CompuServe site containing the drivers and software.
AC Power Connector
Rear View
4. Install Information Assistant:
install your HP NetServer. It is easier to use from a stand-alone system,
rather than from the HP NetServer you are installing. Install Information
Assistant from the HP NetServer Online Documentation CD-ROM
the client system that you will be using to manage your HP NetServer.
5. Visit Order Assistant (optional)
http://www.hp.com/go/netserver
Order Assistant lists HP accessories, cables, and connectors for your
HP NetServer.
6. Obtain IntranetWare key (optional):
optional Novell IntranetWare software that came with your HP
NetServer, purchase the software and obtain the key before beginning
NOS installation in panel 12: "Configure the HP NetServer." Use the key
request form in the HP NetServer Software Option Package.
insert the tabs inside the rear of the cover
1. To replace a cover,
into the slots at rear of the chassis and slide the side cover toward
the rear. Tighten the thumbscrew at the front of the cover.
insert the tabs at the bottom of the bezel
2. To replace the bezel,
into the slots at the bottom of the chassis front and press the top of
the bezel to the chassis until it snaps into place. Lock the bezel lock
with the key provided.
3. Replace all power, telephone, and I/O cables.
Bezel Lock
Unlocked Position
Cover 2
Cover 1
Thumbscrews
Mouse
Keyboard
Monitor
Information Assistant will help you
onto
on the Internet at
If you plan to install the
Tabs and Slots
Cover 3