HP D7171A - NetServer - LPr Reference Manual

Hp netserver lh 3 and lh 3r quick service guide.
Hide thumbs
HP NetServer LH 3/LH 3r
Quick Service
Reference Guide
Last Updated: June 1999

Advertising

   Related Manuals for HP D7171A - NetServer - LPr

   Summary of Contents for HP D7171A - NetServer - LPr

  • Page 1

    HP NetServer LH 3/LH 3r Quick Service Reference Guide Last Updated: June 1999...

  • Page 2: Table Of Contents

    Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard.

  • Page 3: Hp Netserver Lh 3 And Lh 3r System Information, Front Control Panel

    HP NetServer LH 3 and LH 3r System Information Front Control Panel Control Description Lock (LH 3 only) Locks system to prevent unauthorized use. DC Power Switchand indicator light Turns the NetServer on and off. This switch is behind the protective door on the front panel. Push once to turn on, again to turn off.

  • Page 4: Rear View

    Keyboard lockand indicator light Locks system keyboard to prevent unauthorized use. Status screen Reports various types of system status. The buttons below the screen control these menu functions Return to a previous selection. Select a menu item. Reserved for future use. Scroll down or up.

  • Page 5: Removing The Covers (lh 3x), Removing The Covers (lh 3r), Memory, Cover 1 Cover, Cover

    Removing the Covers (LH 3X) Cover 3 Cover 1 Cover 2 Cover 2 Cover 3 Cover 1 Removing the Covers (LH 3r) Cover 1 Cover 2 Cover 3 Memory There are four DIMM sockets on the system board for memory expansion. You can use 64 MB, 128 MB, and 256 MB DIMMs for a maximum capacity of 1 GB of RAM.

  • Page 6: Boot Device Priority, Dimm Slot Led Blink Codes

    Boot Device Priority Slot 1 16-bit ISA or 32-bit PCI Slot 2 32-bit PCI Slot 3 32-bit PCI Slot 4 32-bit PCI Slot 5 32-bit PCI Slot 6 32-bit PCI Slot 7 32-bit PCI Slot 8 32-bit PCI Boot order for PCI controllers is determined by slot location. The system searches for a bootable device in the following order: IDE CD-ROM drive with a bootable CD-ROM.

  • Page 7: Exploded Views

    Processor or Install processor in primary processor socket Terminator Board Not and a processor or terminator board in Installed secondary processor socket. DIMM Status Error Codes When no processor error condition exists, each diagnostic LED display the status of the DIMM in the corresponding socket, as follows: OFF: no DIMM installed Flashes ON and OFF at 1 Hz in 50/50 proportion of time: defective or inappropriate DIMM...

  • Page 9: Hp Netserver Replaceable Parts List, Cover

    HP NetServer Replaceable Parts List Description Replacement Exchange System board PCA D5000-60001 D5000-69000 I/O PCA 5064-1996 D5000-69001 Backplane PCA 5064-1997 Pentium II 350mhz processor 1821-4201 Pentium II 400mhz processor 1821-4202 Heat sink for processor module 5183-2471 Heat sink clip 5183-2472 Terminator PCA ( plugs in secondary processor slot in 5183-3418 dual-ready systems)

  • Page 10

    Non-hot-swap tray, hard disk drive (3 ea.) D2198B Non-hot-swap tray, removable media device (2 ea.) D2199A 4.2 GB Ultra/Wide SCSI drive, 7200 rpm (for non-hot- D4910A swap use) 9.1 GB Ultra/Wide SCSI drive, 7200 rpm (for non-hot- D4911A swap use) 9.1 GB low-profile Ultra2 drive, 7200 rpm (for hot-swap D6106A use)

  • Page 11: Keyboards, Power Cords, Hot-swap Hard Disk Drive Led Status And Activity Indicators

    Keyboards Language Part Number Language Part Number D4950-63001 Danish D4950-63016 Arab/French D4950-63025 Fr.Canadian D4950-63002 Portuguese D4950-63027 German D4950-63003 Cyrillic D4950-63030 Spanish D4950-63004 Belgian/Flemish D4950-63014 French D4950-63005 Italian D4950-63017 Norwegian D4950-63009 Arab/English D4950-63020 Swiss D4950-63011 Korea/Hangu D4950-63021 Swedish D4950-63012 Taiwan D4950-63023 D4950-63013 Poland D4950-63035...

  • Page 12: System Board Illustration, System Switches

    System Board Illustration System Switches...

  • Page 13: Specifications

    Specifications Operating Temperature 5 to 35 C (41 to 95 F) Non-operating -40° to +65° C (-40° to +149° F) Temperature Operating Humidity 20% to 80% relative humidity, non-condensing Non-operating Humidity 5% to 95% relative humidity, non-condensing Operating Altitude -30 to 3,000 m (~10,000 ft) Non-operating Altitude -30 to 12,000 m (~40,000 ft) Minimum Clearance...

  • Page 14: Notes

    Notes:...

Comments to this Manuals

Symbols: 0
Latest comments: