990 / 880 / 770 User Manual Software version E3 D12788-05 This document is not to be reproduced in whole or in part without permission in writing from:...
Page 3
Waste handling: No need to send material back to TANDBERG as there are no consumables to take care of. Please contact your local dealer for information on recycling the product by sending the main parts of the product for disassembly at local electronic waste stations, marking recyclable parts so the waste station can disassemble and re-use these parts.
If the apparatus has been subjected to excessive shock by being dropped, or the cabinet has been damaged If the apparatus fails to operate in accordance with the operating instructions TANDBERG Videoconferencing System Equipment Markings The lightning flash symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltages”...
Contents Introduction ... 7 Menu structure ... 8 The TANDBERG Videoconferencing System ... 9 Installation ... 11 Precautions ... 11 Unpacking ... 11 MPORTANT LEASE Connecting cables ... 12 READ THIS SECTION Power on ... 14 CAREFULLY FOR OPTIMAL System configuration... 15 SYSTEM SET Getting started ...
Page 6
TANDBERG Videoconferencing System Advanced use ... 43 Main menu ... 43 Call quality ... 44 Presentations ... 46 Utilities ... 48 MCU services ... 51 Audio Settings ... 55 Video Settings ... 62 Terminal Settings ... 66 Network Configuration ... 66 LAN Settings ...
Introduction This User Manual is provided to help you make the best use of your TANDBERG system. The TANDBERG system offers superior audio and video quality in a fully-featured unit. The ‘Welcome’ menu will show the name of your product.
Quick Menu Request Floor Release Floor Terminal Names View Site # End View Chair Control Press U Press O to select. TANDBERG Videoconferencing System Main Menu Audio MCU Services Settings Inputs Level Settings Outputs Echo Control AGC Settings Tones&Volume Restore Audio...
TANDBERG Videoconferencing System Camera The built-in camera includes a high quality colour camera with a fast pan/tilt/zoom action. The camera is controlled by the system’s infra-red remote control and operates pan/tilt, focus and zoom. Codec The Codec is the heart of the system. The main task for the Codec is the compression of outgoing video, audio and data, the transmission of this information to a remote site and the decompression of the incoming information.
• This product complies with directives: LVD 73/23/EC, EMC 89/366/EEC, R&TTE 99/5/EEC Unpacking The TANDBERG 990 / 880 /770 consists of the following items: • Videoconferencing system with built-in camera • Table Microphone • Remote Control •...
( or Scart adapter). If you do not have an S-video connector on your monitor, connect the RCA-RCA video cable to the RCA connector on your monitor. • Connect the other end to ‘Video Out’. TANDBERG Videoconferencing System Connecting with Scart Power TV/Monitor Scart...
NOTE AKE SURE YOU INSERT THE CARD IN THE RIGHT DIRECTION ‘E ’ JECT BUTTON POPS UP See ‘Wireless LAN Settings’ for configuration. TANDBERG Videoconferencing System ISDN LINES ISDN LINES OU WILL NEED THEM LATER TO CONFIGURE THE SYSTEM NETWORK...
Installation TANDBERG Videoconferencing System Power on Power on the monitor and use the monitor remote control to select the Audio/Video input used (refer to your monitor manual). If you are using S-video from the system, remember to select S-Video input to avoid a black and white picture.
A dial tone should be heard if the network is active. ONNECT • Using the monitor remote control, adjust the volume on the monitor to a level of your choice. This volume will be the default volume for all calls. TANDBERG Videoconferencing System ‘T ’, ‘N ELECT THE MENU...
Specify the necessary LAN settings according to the instructions from your LAN administrator. If there is an H.323 Gatekeeper present on your LAN, see also ‘H.323 Settings’. For details, follow the instructions in chapter ‘LAN Settings’ in this manual. TANDBERG Videoconferencing System...
TANDBERG Videoconferencing System Getting started Getting started System start-up Your system should be in standby mode. When in standby mode, pressing any key or picking up the remote control will wake up the system. An incoming call will also wake up the system.
Dialing keys / Preset keys Used to make a call. The twelve number keys, (0-9), #, * operate in the same way as on a modern push-button telephone. These buttons are also used when entering a name into a text field. TANDBERG Videoconferencing System...
123.3.0.12. If a gatekeeper is present, you may place IP-calls using “telephone-style” numbers (an E.164 alias), according to the numbering plan implemented in the gatekeeper. The dialed number will then be translated into an IP-address by the gatekeeper. TANDBERG Videoconferencing System Getting started...
Page 20
(after connected to the MCU). ADDRESS IS USED TO ADDRESS DIFFERENT SYSTEMS ON THE SAME TCS-4 IS USED TO ADDRESS DIFFERENT SYSTEMS ON A TANDBERG Videoconferencing System ISDN LINE LAN,...
Page 21
CALL USING KBPS OR KBPS ‘2 :’ ARE DISPLAYED NTER THE SECOND NUMBER TANDBERG Videoconferencing System KBPS NETWORK Y DEFAULT THE SYSTEM WILL DIAL AN UNRESTRICTED CALL KBPS IF NECESSARY O FORCE A RESTRICTED CALL ORTH MERICA IT IS NECESSARY TO DIAL BOTH ‘128’...
Page 22
Getting started TANDBERG Videoconferencing System Selecting / setting default network To select a specific network, press the ‘Net’ Quick Key when you are in the dial menu.: 1 Highlight the network to be used in your call. 2 Press ‘Select’ to select network or press ‘Set as Default’ to set the selected network as your preferred choice for this and all subsequent calls.
‘Advanced use’. End a call To end a call, press D disconnect Correcting keying mistakes To delete the last digit (or character) entered, press D delete TANDBERG Videoconferencing System ONNECT ISCONNECT ELETE Getting started NDING A CALL WITCHING OFF THE MONITOR...
The MultiSite entries will not be displayed when you are in a call. By using the dataport file system or external management systems like the TANDBERG Management Suite, it is possible to store 400 additional entries. These entries can only be changed from the dataport or the management system.
To edit an entry, highlight the entry you want to edit and press ‘Edit Entry’. Edit the entry and select ‘Previous Menu’ to return to the Directory menu. Delete Entry To delete an entry, highlight the entry and press D TANDBERG Videoconferencing System ON THE REMOTE CONTROL ELETE Getting started...
Highlight the entry you want to add to the meeting and press O ‘Add New Entry’ to add an new point-to-point directory entry. LOBAL ENTRIES WILL NOT BE AVAILABLE FOR FOR NOTE TANDBERG Videoconferencing System KBPS WO ENTRIES ARE ADDED ONE WITH...
In a call, if audio is detected, the on-screen symbol will start to flash. Pressing M one more time will activate the microphone again. NOTE RESSING FF WILL MUTE AUDIO INPUTS TANDBERG Videoconferencing System . An on screen indicator will appear when the 1-2. I T WILL NOT MUTE AUDIO FROM AUDIO INPUT General use...
When Do Not Disturb is activated, the system will not accept any incoming calls. The caller will hear a busy tone when calling this unit. A status line will indicate when Do Not Disturb is active. * Optional feature TANDBERG Videoconferencing System...
HEN SELECTING THE DOC CAM OR PC VIDEO SOURCES THE SYSTEM WILL AUTOMATICALLY REQUEST FLOOR WHEN CONNECTED TO A CONFERENCE AS ULTI ITE HOST OR CONNECTED TO AN EXTERNAL TANDBERG Videoconferencing System zoom for zooming. THE ARROW KEYS WILL NAVIGATE IN THE MENUS to select the video source to be transmitted to the far end.
• disconnecting the call. An on-screen indicator ‘CamTrackOff’ will appear. HE CAMERA TRACKING SPEEDS MAY BE ALTERED IN THE TANDBERG Videoconferencing System MUST BE RELATED TO THEREFORE ALL PARTICIPANTS WHO ARE LOCATED CLOSEST TO HEN CAMERA TRACKING IS ACTIVATED AND A PERSON CLOSE TO ‘V...
Storing preset 10 to 15 To store preset 10-15 the TANDBERG Tracker has to be used: • Select which preset to be used on the TANDBERG Tracker (see separate documentation). • Press S once on the TANDBERG Remote Control and wait for the on-screen indicator to appear.
T DEPENDS ON THE FAR END SYSTEM CONFIGURATION IF THE FAR END DOCUMENT CAMERA IS DISPLAYED WHEN To prevent others controlling your camera, select ‘Far End Camera Control:Off’ in ‘Utilities’. TANDBERG Videoconferencing System for zooming. zoom AM IS PRESSED...
• Press F until the ‘FarEndCamera’ on screen indicator is displayed. • Press S . A snapshot from the far end is automatically displayed. NAPSHOT TANDBERG Videoconferencing System NOTE HEN IN A CONFERENCE AS MCU, SENDING A SNAPSHOT WILL AUTOMATICALLY INITIATE A FLOOR REQUEST ‘P...
NOTE IDEO N EXTRA CALL WILL BE MADE AND * - Optional feature. TANDBERG Videoconferencing System IDEO WITHIN THE SAME CALL T IS NOT NECESSARY TO MAKE A NEW CALL AND THE CONNECT TIME IDEO IS ALSO UNI DIRECTIONAL AND HENCE...
Page 35
F THE MAIN CONNECTION IS SHOWN IN FULL SCREEN CONNECTION SOURCE If both connections are selected to display the same video source, Duo Video will be closed. TANDBERG Videoconferencing System . Select if you want to disconnect only the Duo Video ISCONNECT...
KBPS NOTE - 4 SITES INDICATES YOURSELF THREE OTHER SITES * - Optional feature. TANDBERG Videoconferencing System A conference can consist of any combination of ISDN/ LAN sites. It is possible to have telephone meetings with up to 5 participants.
TANDBERG Videoconferencing System General use MultiSite cascading By connecting four MultiSite systems together, it is possible to connect up to 10 video sites (including the four MultiSite sites) plus 4 audio sites (telephones), see drawing below. The host can connect up to 3 other video systems with MultiSite functionality. The host can use Voice Switched or Continuous Presence mode.
Page 38
To use another network operator, press ‘Net’ and select operator in the Net menu. • Press C connect ONNECT T IS POSSIBLE TO CONNECT SEVERAL TELEPHONES TANDBERG Videoconferencing System SITES IN ADDITION TO THE HOST KBPS WHEN CONNECTING THE OTHER SITES VIDEO SYSTEMS TELEPHONES...
Page 39
Disconnecting sites from a conference disconnect To disconnect a site or end the conference, press D • Select site and press O To end the meeting press ‘Disconnect All’. TANDBERG Videoconferencing System ISCONNECT or ‘Disconnect Site’. General use O FIND THE DIAL IN NUMBERS FOR THE ‘M...
• Start the VNC software on your PC. • Press PC on your remote control. Use UP/DOWN to activate PAGE UP/PAGE DOWN on the PC. For setup information and details, see ‘VNC Settings’ in ‘Advanced use’. * - Optional feature. TANDBERG Videoconferencing System VGA Output VGA- (VESA...
See ‘LAN Settings’ in ‘Advanced use’ for further information. • Start your Web-browser. In the address field type the IP-address of the codec. Enter the password and the Web-page of the codec will be shown. The default password is ‘TANDBERG’. Text Chat / Closed Captioning While in an ISDN or IP call to another system supporting Text Chat (T.140), select ‘Text Chat’...
General use TANDBERG Videoconferencing System Streaming To view streaming, select ‘Streaming’ from the Web-page of the codec. See separate ‘Streaming’ section in this manual for further information. Snapshots Snapshots of current stream (if MultiSite), selfview, far end and DuoVideo streams are accesible via http.
M Menu Password It is possible to password protect the menus on the TANDBERG system. To activate this feature, specify a Menu Password in the Utilities menu. By doing this, only dialing and camera control commands will be available. When...
CAPABILITIES WILL ENABLE BETTER VIDEO QUALITY FOR - If option ‘Presenter’ is not installed or if H263 is not used, only CIF resolution will be used for all selections. - MainCam/Aux/VCR will select ‘Motion’. DocCam/PC will select ‘Sharpness’. TANDBERG Videoconferencing System NTSC (SIF: 352 SYSTEMS G722.1...
Video off/on, Audio off/normal/high Advanced Shows video/audio standards (Example: Video: H261 CIF, Audio: G722). * - Requires option ‘Presenter’. To check which options are installed, see the ‘System Info’ menu in ‘Diagnostics’. TANDBERG Videoconferencing System Advanced use ‘A ’ NOTE...
Manual: Duo Video must be opened by pressing C * - Requires option ‘Presenter’ and H263 video. To check which options are installed, see the ‘System Info’ menu in ‘Diagnostics’. ** - 4CIF: PC and DocCam, otherwise CIF. TANDBERG Videoconferencing System select ‘Presentation Mode: Normal’. NAPSHOT again.
MCU conference. When selecting ‘Doc Cam’ or ‘PC’ video sources, the system will not Request Floor. * - Requires option ‘Presenter’. To check which options are installed, see the ‘System Info’ menu in ‘Diagnostics’. TANDBERG Videoconferencing System Advanced use ELFVIEW...
Dual Monitor Selfview, snapshots and Duo Video will be displayed on the 2nd monitor. Off: The 2nd monitor shows Selfview only. TANDBERG Videoconferencing System to switch the microphone on. key. ONNECT...
• when using the Web-interface. • when the codec is acting as an SNMP Agent. • towards a DHCP server. • as an H323 ID. Other systems can call in using this name instead of IP-number/IP-address. TANDBERG Videoconferencing System ‘O ’ ‘R...
Advanced use Menu Password Enter the code which should be entered to get access to the menus on the TANDBERG system. When pressing the ‘Menu’ button on the remote control, the user will be asked to enter the Password written here.
The system can also control external MCUs in a very flexible manner using the functions described below. URING AN CONFERENCE A STATUS LINE WILL PROVIDE INFORMATION ABOUT THE CONFERENCE ‘U ’, ‘MCU S TILITIES TATUS TANDBERG Videoconferencing System MCU, M ULTI WHICH SUPPORTS UP TO WITCHED AND ONTINUOUS RESENCE MODE ’.
Advanced use TANDBERG Videoconferencing System Quick Menu When connected to an MCU RESS ANY UICK KEY WHEN IN A MULTIPOINT CONFERENCE TO ACTIVATE THE UICK This menu provides access to the most commonly used MCU functions. If ‘ Request Floor’ is selected, ‘Request Floor’ will change to ‘Release Floor’.
Allows you to stop viewing the site previously chosen with ‘View Site #’, and returns your view to the site that is currently ‘On Air’. ‘V ’ ‘E ’ CAN BE USED BY ALL CONFERENCE PARTICIPANTS * - NOT supported by the MultiSite TANDBERG Videoconferencing System Advanced use...
Allows the chairman to disconnect any participant in the conference. Terminate meeting Allows the chairman to terminate the conference altogether. * - NOT supported by the MultiSite TANDBERG Videoconferencing System N ORDER TO MAKE USE OF MUST SUPPORT HAIR ONTROL FEATURES THE (H.243).
XTERNAL MIXER HEN USING AN EXTERNAL MIXER ADAPTIVE MIXERS MIGHT CAUSE THE ECHO CANCELLER TO MALFUNCTION TANDBERG Videoconferencing System IT IS VERY IMPORTANT THAT THIS IS A FIXED MIXER Advanced use UTOMATIC...
Audio Technica AT871 Audio Technica AT851R TANDBERG Audio Science Audio inputs 3 and 4 are set to a default level which is adhered to by most manufacturers of audio-visual equipment and is a level at which most audio-visual equipment (CD-players, VCRs) will work.
TO A LOUDSPEAKER PLACED IN THE SAME ROOM AS THE MICROPHONES CONNECTED TO THE SYSTEM NOTE “ ” WILL CAUSE HOWLING AND POSSIBLE DAMAGE TO THE SPEAKER SYSTEM If an output is ‘Off’, no audio will be sent to that output. TANDBERG Videoconferencing System Advanced use OING THIS...
NR reduces constant background noise (e.g. noise from air-conditioning systems, cooling fans etc.). In addition, a highpass filter (Humfilter) reduces very low frequency noise. Choose On+NR to activate both Echo Control and Noise Reduction. TANDBERG Videoconferencing System ‘O ’ IF EXTERNAL ECHO CANCELLATION OR PLAYBACK EQUIPMENT IS USED...
Page 59
The system adapts slowly to acoustic changes in the room. Decrease the setting. After a change, the system will need a few seconds to re-adjust. Motion If you experience echo caused by movements in the room, increase the value. TANDBERG Videoconferencing System Advanced use...
Page 60
• Place all microphones as far as possible from noise sources. • Reduce the volume setting. Ensure that the loudspeaker does not distort the audio. TANDBERG Videoconferencing System AGC, IT IS CRUCIAL THAT THE LEVELS ON THE INPUT CONNECTORS ARE ADJUSTED CORRECTLY...
There are many audio settings and the codec could easily be made unusable by configuring these by mistake. It is therefore possible to return all audio settings to their factory default settings by using Restore Audio Defaults. TANDBERG Videoconferencing System Advanced use...
Pressing PC will activate the VGA input on the system (default). VNC: Pressing PC will use VNC to show images from your PC (see ‘VNC Settings’ for further information). * - Requires option ‘Presenter’. To check which options are installed, see the ‘System Info’ menu in ‘Diagnostics’. TANDBERG Videoconferencing System...
OK. WHITE OBJECT SHOULD BE HELD IN FRONT OF THE CAMERA A FEW SECONDS BEFORE AND AFTER SELECTING Video Name TANDBERG Videoconferencing System As a default each video input corresponds to the name used on the remote control. To edit the name, use the number keys on the remote control.
Will sense the resolution on the ‘VGA input’ port and use the same resolution on the ‘VGA Out’ port. VGA: Will force ‘VGA out’ to VGA(640X480). SVGA: Will force ‘VGA out’ to SVGA(800X600). XGA: Will force ‘VGA out’ to XGA(1024X768). TANDBERG Videoconferencing System ‘VGA O ’ ‘M ’, NOTE...
To activate VNC, press ‘PC’ on the remote control. See also ‘PC SoftPresenter’ section for further information. * - Requires option ‘Presenter’. To check which options are installed, see the ‘System Info’ menu in ‘Diagnostics’. TANDBERG Videoconferencing System VNC S...
ISDN SWITCH TYPE ISDN (+ SPID NTER LINE NUMBERS ISABLE UNUSED LINES TANDBERG Videoconferencing System This menu provides basic network setup for the unit and should be used when installing the system. NOTE NOTE ISDN-BRI, MAKE THE FOLLOWING SETTINGS S IF REQUIRED...
ISDN switch type Select the type of ISDN network connected to your unit TANDBERG Videoconferencing System Advanced use NOTE 1TR6 SHOULD ONLY BE USED IF YOU ARE PABX. OPERATING THE SYSTEM BEHIND A...
National ISDN and AT&T Custom ISDN might require SPID numbers associated with your ISDN numbers. If you have received two different SPID numbers for each ISDN line from your telephone company, you must program both. Example: ISDN BRI 1: ISDN BRI 2: ISDN BRI 3: TANDBERG Videoconferencing System Numbers SPIDS 67838498 016783849800 67838498 016783849810...
Page 69
TANDBERG Videoconferencing System Advanced use Advanced ISDN settings Subaddress Using a subaddress enables you to connect up to eight ISDN terminals to the same ISDN telephone number and line. The terminals are addressed by using different subaddresses. To call a terminal with a subaddress, separate the ISDN telephone number and the subaddress with a ‘*’.
Sending Complete The system will send the ISDN message information element ‘Sending Complete’. The system will not send ‘Sending Complete’. TANDBERG Videoconferencing System Call 12345601 Line 1 Setup, Number1: 602 Validate Numbers (MSN): On...
This is used for streaming data to limit how many routers the data should pass before it is rejected. If TTL is set to 2, data will not traverse more than 2 router hops. * - Please contact your TANDBERG representative for further information. TANDBERG Videoconferencing System...
After streaming is started, an easy way to view the streamed audio/video is to start your Web-browser and enter the IP-address of the streaming system. After the Web page of the codec is shown, click on ‘Streaming’. Alternatively, enter http://<codec ip-address>/stream.sdp. TANDBERG Videoconferencing System...
Page 73
Manual The codec will use a specific gatekeeper identified by ‘Gatekeeper IP-address’. The codec will not use a gatekeeper and an IP-address must be used in order to make an H.323 call. Gatekeeper IP-address This is the gatekeeper IP-address if you specify ‘Use Gatekeeper: Manual’. TANDBERG Videoconferencing System Advanced use...
Page 74
When dialing a number prefixed with digits specified by ‘H.323 Prefix’, and with ‘Net: Auto’, an H.323 call will be placed. Example: H.323 Prefix is ‘555’. Dialling ‘55582’ with ‘Net:Auto’ will select LAN. Register Pressing ‘Register’ will send a gatekeeper registration request. This request will also be sent when leaving the menu. TANDBERG Videoconferencing System...
In the router, the following ports must be routed to the codec’s IP-address: Port 1720 Port 5555-5560 Port 2326-2365 Please contact your TANDBERG representative for further information. H.323 Ports Static When selecting static H323 ports for TCP connections the ports 5555 or 5556 will be used for Q931 and H245 respectively.
Page 76
Diffserv Used to define which priority Audio, Video, Data and Signaling packets should have in an IP network. The priority ranges from 0 to 63 for each type of packets. TANDBERG Videoconferencing System Auto will provide the following priority: Audio...
When using DHCP, the default gateway will be set automatically. If the LAN utilizes static IP addresses, IP address, subnet mask, and default gateway must be specified by the LAN administrator. TANDBERG Videoconferencing System Advanced use HANGES IN THIS MENU WILL NOT HAVE...
100 Mbps speed/Full Duplex. Restart Pressing the Quick key ‘Restart’ will restart your system without having to use the On/Off switch on the codec. If IP-assignment is changed, it is sufficient to use this Quick key to restart the system. TANDBERG Videoconferencing System...
CARD USED MUST COMPLY WITH THE RELEVANT REGULATIONS FOR SUCH CARDS IN THE COUNTRY WHERE IT IS USED SPN-270-12, ADAPTER OWER WHICH COMPLIES WITH THE REQUIREMENTS FOR LIMITED POWER SOURCE ACCORDING TO TANDBERG Videoconferencing System Recommended access point • Compaq WL410 base station Advanced use HE UNIT MUST BE SUPPLIED BY POWER SUPPLY...
Page 80
The 128-bit key can consist of a leading star (*) and 13 characters. Start with a * and then the text. Example: 128 bit key: *secretkeyhome. NOTE NCREASED ENCRYPTION LEVEL WILL DECREASE PERFORMANCE TANDBERG Videoconferencing System Encryption using Hex numbers The 64-bit keys can consist of 10 hexadecimal digits. Example: “de01ad4dbe”.
TANDBERG Videoconferencing System Advanced use SNMP Settings SNMP Trap Host SNMP (Simple Network Management Protocol) is used for monitoring and configuring different units in a network. The codec’s SNMP Agent responds to requests from SNMP Managers (a PC program etc.). SNMP traps are generated by the agent to inform the manager about important events.
When pressing CONNECT or any number to make a call, an Access Code menu will be shown. The user will then have to enter the correct Access Code in order to make a call. No Access Code is necessary to make a call. TANDBERG Videoconferencing System...
DES is not supported by all other sites, no other type of encryption will be initiated. AES* DES E NCRYPTION IS SUPPORTED FOR MIXED CONNECTED AT THE SAME TIME ULTISITE CAN RUN ENCRYPTED SITES AT * Optional feature TANDBERG Videoconferencing System ISDN/IP CALLS N ADDITION 128 K BPS AND ENCRYPTED SITES AT Advanced use...
NUMBER DIALED WILL BE Using the three last profiles you can enter the name of a profile, prefix and network selection. This is useful if you have a fixed prefix for your service provider. TANDBERG Videoconferencing System , ISDN. I 12345678...
When using this mode, it is necessary to have a TANDBERG system at the far end. Control mode The control interface provided by the Dataport...
Page 86
Advanced use TANDBERG Videoconferencing System Dataport 2 Dataport 2 is dedicated to the main camera and will not be available in standard configuration. The Codec will automatically detect WAVE cameras. If you are using a camera supporting the VISCA protocol, select ‘Mode: VISCA’.
Presenter functionality. A restart of the system is required after entering a new option key. If the option key is invalid, the original key will be used. The following options are available 1. No option 2. NPP (Presenter) 3. MultiSite + NPP 4. Security + NPP 5. Security + NPP + MultiSite TANDBERG Videoconferencing System Advanced use...
Sync when the channels are synchronised Active when all available channels are connected Releasing waiting for the network to confirm a release of the call Released when disconnected - the network has acknowledged the disconnection TANDBERG Videoconferencing System...
100 - Invalid information element contents 102 - Recovery on timer expiry 127 - Internetworking, unspecified 255 - TANDBERG specific. undefined cause code TANDBERG Videoconferencing System ’ TO BRING THIS MENU UP WHEN NOT IN THE MENU SYSTEM Advanced use...
Comprehensive information about the call is available through the Call Status window. The menu has two columns, one for transmitted and one for received audio/video/data information. If Duo Video or MultiSite is used, pressing the LEFT/RIGHT keys will show one page per connected site. Please contact your TANDBERG representative for further information.
‘Far End Loop’ will be set to ‘Off’. System Selftest The system performs a check to determine internal hardware integrity. Test Network is useful when you want to check if your network connection is active. TANDBERG Videoconferencing System Advanced use...
HIS DEFAULT SETTING WILL NOT AFFECT YOUR IP Address Conflict Check The codec will give a warning if there is an IP conflict. This check may be initiated by the user by selecting IP Address Conflict Check. TANDBERG Videoconferencing System IRECTORY INFORMATION ETWORK SPID...
TANDBERG Videoconferencing System Peripherals Peripheral Equipment Using the optional peripheral devices outlined in this chapter and the many others available, you will be able to build your own applications for use with the system, thereby better integrating the system into your business environment.
Page 94
• 1 VCR output (line level) via RCA connector providing a mixed signal between audio from the local side (except from the VCR input) and audio from the far end. This output is intended for connection to a VCR. TANDBERG Videoconferencing System...
TANDBERG Videoconferencing System Peripherals Dual Monitor It is possible to install the system in a Dual Monitor configuration. The Dual Monitor can be used to show full screen selfview, still images and Duo Video. To use the system in the Dual Monitor configuration: •...
0 and F. For preset 10 to 15, the numbers 9 to F should be selected. Please refer also to ‘Presets’ in the ‘General Use’ - section. For more information, contact your local TANDBERG representative. TANDBERG Videoconferencing System on the remote control...
Video VCR: Audio Input Codec: Video Output 2 VCR: Video Input TANDBERG Videoconferencing System CONNECTORS ARE MARKED For playback, connect a cable between Video Out on the VCR and ‘VideoIn 4 (VCR)’ on the system. Connect a cable between Audio Out on the VCR and the VCR audio input on the system.
You can connect up to three microphones to your system. The connectors are marked Mic1, Mic2 and Mic3. The connected microphones will by default be mixed. When more than one microphone is connected you have the option to use the Voice Activate Camera Positioning feature. TANDBERG Videoconferencing System...
U-interface Wall Connect the U-interface of your NT1 adapter to the line provided from your network provider. TANDBERG can provide NT-adapters. For convenience the NT1 adapters could be placed inside the cabinet. If needed, use the shorter ISDN cable (RJ45 connectors) delivered with the NT1 between the codec and the NT1 and the longer ISDN cable between the NT1 and the connector (RJ45) at the wall socket.
Important: Use the Quick key ‘Set Restrict (56k)’ in the Quality menu to specify a restricted call (56k) when you dial a number. Set Restrict (56k) Example: One number dialing enter: Two number dialing enter: TANDBERG Videoconferencing System ISDN1 BRI S/T TANDBERG Number: 1703111222...
TANDBERG Videoconferencing System Appendices Appendix 3: Environmental considerations This section explains how to carry out basic adjustments and simple tests to ensure that you send and receive the best possible image and audio quality when using your system. Iris control and lighting By default the system camera will use an automatic iris to compensate for changes in lighting.
Page 102
1–3: Prestored camera views Grand Vison Document camera system Leader Board TANDBERG Videoconferencing System Audio: - Noise Floor preferred less than 44dBC. - Reverb Time .3 to .5 sec. - Ventilation: - Keep in mind Noise Floor. - Velocity = Noise. Therefore keep velocity of air low.
- the system software globdir.prm - file containing up to 400 entries. These entries can not be edited from the TANDBERG Videoconferencing system, but can be edited as a text-file. Files accessible only by ‘ftp get /tmp/snapshots/xxx.jpg’ or ‘http://<IP-address of codec>/tmp/snapshots/xxx.jpg’: main.jpg...
Page 104
Appendices TANDBERG Videoconferencing System Custom logos · Go to the folder where your logo is located. NOTE : 704 OGO MAX SIZE FILE FORMAT F THE FILE IS TOO LARGE NO LOGO WILL BE DISPLAYED · Type ftp <IP-address of your local codec>.
· Exit from ftp, type ‘bye’. Menu Password: Access to the menu system on the TANDBERG Videoconferencing unit can be controlled using password protection. This is done by using the following dataport command: menupassword set <pin-code>. The pin-code should be maximum 5 - five digits. To erase the menu access code, enter an empty pin-code.
Page 106
TANDBERG Videoconferencing Unit. IP Password By setting a IP Password on the TANDBERG codec, all access to the system using IP (Telnet, FTP, WEB) requires a password. This password can be enabled from telnet or dataport using the command: ippassword <ip-password>. The default IP password is ‘TANDBERG’.
Page 107
All TANDBERG systems support both AES* and DES encryption. By default this feature is enabled such that when connecting with any other video system or MCU, a TANDBERG system will attempt to establish a secure conference using AES* or DES encryption. The TANDBERG system will attempt this for both IP and ISDN connections.
LAN call 19 making a video call 19 restricted 21 Call Quality menu 44 Call Settings 81 Call status 89 Camera TANDBERG Videoconferencing System controlling 29 extra camera 97 tracking modes 62 Cause codes 88 Chairman functionality 51 Channel status 87...
Page 110
Multipoint Control Unit (MCU) 51 MultiSite (Built-in) 36 MultiSite cascading 37 NAT Address 74 Natural Video 7, 44 Network configuration 66 Network Profiles 83 TANDBERG Videoconferencing System NT1 13 NTSC 93 PAL 93 Parallel dial 70 PC 62 PC Presenter 40...
Page 111
Viewing a still image 33 VNC 62 VNC Settings 65 Voice Activated Camera Positioning 30 Voice Switched 51 Volume 27 TANDBERG Videoconferencing System Waste handling 3 Web Snapshots 50 Welcome menu 17 Whitebalance 63 Wireless LAN Settings 78 WWW-interface 41...
Need help?
Do you have a question about the 880 and is the answer not in the manual?
Questions and answers