Rear Panel - Panasonic AW-RP305 Service Manual

!8 Zoom Lever [ZOOM, TELE/WIDE]
Used to adjust the zoom of the lens.
varies according to the angle of the lever. The lens
moves toward TELE when the lever is moved toward
TELE, or toward WIDE when the lever is moved toward
WIDE, provided that ZOOM REVERSE Switch @7 is in
the NOR position. When ZOOM REVERSE Switch @7 is
set to the REV position, the lens moves in the opposite
direction. ZOOM/FOCUS EXCHANGE Switch @8 may
be used to exchange its function with FOCUS Lever !9 .
!9 Focus Lever [FOCUS FAR/NEAR]
Used to adjust the focus of the lens. Used to adjust the
lens focus at varying speed depending on the angle of
the lever. The lens is focused far when the lever is
moved toward FAR, or near when the lever is moved
toward NEAR, provided that FOCUS REVERSE Switch
@9 is in the NOR position. When FOCUS REVERSE
Switch @9 is set to the REV position, the lens focus
operates in the opposite direction. ZOOM/ FOCUS
EXCHANGE Switch @8 may be used to exchange its
function with ZOOM Lever !8 .
@0 Pan/tilt Lever [PAN/TILT, UP/DOWN/LEFT/RIGHT]
Used to control the pan/tilt operation of the pan/tilt head.
Controls the head's pan/tilt operation at varying speed
depending on the angle of the lever. The pan/tilt head
turns up when the lever is moved toward UP, or down
when it is moved toward DOWN, provided that TILT
REVERSE Switch #0 is in the NOR position.
pan/tilt head moves in the opposite direction if the TILT
REVERSE Switch #0 is in the REV position. The pan/tilt
head turns leftward when the lever is moved toward
LEFT, or rightward when it is moved toward RIGHT,
provided that PAN REVERSE Switch #1 is in the NOR
position. The pan/tilt head moves in the opposite direc-
tion if the PAN REVERSE Switch #1 is in the REV posi-
tion.
Note: TILT REVERSE Switch #0 and PAN REVERSE
Switch #1 may be used to reverse the operating
direction of the pan/tilt head, but be sure to set the
operating direction of the pan/tilt head with its
mounting direction selection switch during its instal-
lation depending on whether the pan/tilt head is
mounted on the floor or is suspended. Unless the
mounting direction selection switch on the pan/tilt
head is properly set, the pan/tilt head will pan or tilt
in the opposite direction and the pan/tilt head opera-
tion limiters will not be properly stored in the memo-
ry. For details on the setting of this switch, refer to
the INSTALLATION OF PAN/TILT HEAD at page 5.
Zoom speed
@1 TALLY Terminal [TALLY] (AW-RP301: 2-pin Termi-
The
@2 12V DC Input Connector [DC 12V IN] (DC Jack)
@3 Cord Clamp
@4 Auxiliary Control Input Connector
3

Rear Panel

AW-RP301
AUX CONTROL IN
PAN/TILT
CONTROL OUT
AW-RP305
AUX CONTROL IN
PAN/TILT CONTROL OUT
5 4 3 2
nal Board) (AW-RP305: 6-pin Terminal Board)
Connect it to the tally connector on a special effect gen-
erator (SEG) or a video switcher, for example. When
HOT Terminal on the AW-RP301 or any of [1] to [5] ter-
minals on the AW-RP305 falls to ground voltage level,
the corresponding system TALLY indicator e and the
tally indicator on the Pan/tilt Head (AW-PH300) light red.
Connect the AC Adapter AW-PS301 (optional).
Clamps the DC cord of the AC Adapter AW-PS301
(optional) connected to DC 12V IN Connector @2 to pre-
vent its disconnection.
[AUX CONTROL IN] (8-pin DIN Connector)
External control signals are input to this connector in
controlling the head's pan/tilt, lens zoom, focus and iris
operations.
Note: In externally controlling the pan/tilt head and lens
through this connector, set IRIS LEVEL Control i
on this control panel to the centre point (straight
up), and do not simultaneously operate SPEED
Switch !1 , ZOOM Lever !8 , FOCUS Lever !9 , and
PAN/TILT Lever @0 . Operation errors may occur if
external controls are simultaneously used.
D C 1 2 V I N
T A L L Y
H O T
D C 1 2 V I N
T A L L Y
1
5 4 3 2 1