Advertisement
Quick Links
Technical Information
Cut-off machine STIHL Cutquik
Contents
1. Guard with defined adjustment range
2. Belt guard, screw
3. Set of instruction labels
4. Summary
1.
Guard with defined adjustment
range
1.1
Adjustment range
2
1
A
Left:
Adjustment range (A),
Guard mounted on the inboard side
Right:
Adjustment range (B),
Guard mounted on the outboard side
TI_35_2009_30_01_01.fm
®
TS 410, 420 – Series 4238
In STIHL Cutquik
2
the adjustment range (A and B respectively) of the
guard will be determined by the stop pin (1) installed
into the cast arm and by the lugs (arrows) molded
onto the guard (2).
1
B
STIH)
35.2009
®
TS 410, 420 cut-off machines,
englisch / English
Advertisement
Related Manuals for Stihl Cutquik 4238 Series
Summary of Contents for Stihl Cutquik 4238 Series
- Page 1 STIH) Technical Information 35.2009 ® Cut-off machine STIHL Cutquik TS 410, 420 – Series 4238 Contents 1. Guard with defined adjustment range 2. Belt guard, screw 3. Set of instruction labels 4. Summary Guard with defined adjustment range Adjustment range ®...
- Page 2 Page 2 Technical Information 35.2009 Cast arm Guard The previous versions of the cast arm Left: Previous versions of the guard 4238 701 0201 (TS 410) and cast arm Right: New versions of the guard 4238 701 0200 (TS 420) are being replaced by the The previous versions of the guard dia.
- Page 3 Technical Information 35.2009 Page 3 Stop pin Rubber buffer With the introduction of the new guards Left: Previous versions of the cast arm, (see b 1.3), the stop pin (1) 4224 691 0100 and rubber buffer and screw the limit stop (see b 1.5) are introduced. The stop Right: New versions of the cast arm with pin (1) installed into the cast arm (2), together with...
- Page 4 Page 4 Technical Information 35.2009 Reconfiguring the "cast arm with guard" Remove the adjusting lever – from guard on the inboard side to guard on the outboard side The "cast arm with guard" is mounted on the inboard side by the manufacturer. The "cast arm with guard"...
- Page 5 Technical Information 35.2009 Page 5 Remove the V-belt guard Remove the "cast arm with guard" Loosen screw (1) – in machines with the new belt guard (see b 2), the screw is secured on the belt guard to prevent loss Raise the V-belt guard (2) slightly and pull off towards front Remove the nuts (1)
- Page 6 Page 6 Technical Information 35.2009 Mount "cast arm with guard" – guard on the outboard side Turn the guard so that it is in the position shown (see picture) Install and tighten the stop pin (1) Move the adjusting lever (2) to position (A) Install the bolt (3) and tighten Loosen the bolt (4) of the limit stop (5) Remove the limit stop (5)
- Page 7 Technical Information 35.2009 Page 7 Check the adjustment range of the guard Push the V-belt guard (7) into place Install and tighten screw (8) – in machines with the new belt guard (see b 2), the screw is secured on the belt guard to prevent loss Connect water connection Rotate the guard forwards and backwards as far as possible –...
- Page 8 Page 8 Technical Information 35.2009 Reconfiguring the "cast arm with guard" – from guard on the outboard side to guard on the inboard side Remove the abrasive wheel Remove water attachment Remove the adjusting lever Slacken the V-belt Remove the V-belt guard Remove the V-belt Remove the "cast arm with guard"...
- Page 9 Technical Information 35.2009 Page 9 Belt guard, screw Spare parts The previous versions of the belt guard 4238 700 8101 (TS 410) and the belt guard 1, 2 3, 4 4238 700 8100 (TS 420) are no longer available. The new versions of belt guard 4238 700 8107 (TS 410) and belt guard 4238 700 8109 (TS 420) can also be used for older machines.
- Page 10 Spare parts/service notes "set of instruction labels" (3) 0000 960 0101 can The previous versions of instruction label (1) ® also be used with older STIHL Cutquik TS 420 cut- 0000 967 3521 and instruction label (2) off machines. 0000 967 3511 are no longer available. The new Always attach both instruction labels in the new "set...
- Page 11 6) Previous version of part is replaced by Item 20 7) Previous version of part is replaced by Item 18 in the TS 410 and by Item 20 in the TS 420 © ANDREAS STIHL AG & Co. KG, 2009 Technical Documentation D1/MTK-fr TI_35_2009_30_01_01.fm...
Need help?
Do you have a question about the Cutquik 4238 Series and is the answer not in the manual?
Questions and answers