Editing The User Menu - Sony UHC-8300 Operating Instructions Manual

Repeat steps 1 and 2.
By selecting INS on the line below the character list, you
can enter a space at the cursor position.
Selecting DEL deletes the character at the cursor
position.
You can return to step 1 without changing the character by
selecting RET.
If you enter the permitted maximum number of characters
(up to the stop mark at the right end of the line), the cursor
moves to ESC on the line below the character list.
To register the new string you have set, select END and
press the MENU SEL knob/ENTER button.
To restore the previous string, select ESC and press the
MENU SEL knob/ENTER button.
To return a menu item to its standard value
Select the menu item to be returned to its standard value then
hold the MENU SEL knob/ENTER button pressed for 3
seconds while the arrow marker (,) is displayed.
If "10 SEC CLEAR" has been set to ON on the <FILE CLEAR>
page of the FILE menu, you can return the setting in the
reference file for the item being selected to the factory-set
value by holding the MENU SEL knob/ENTER button pressed
for another 10 seconds.
To end menu operations
Set the DISPLAY switch to OFF.

Editing the USER Menu

You can select desired pages and items from the
OPERATION, PAINT, MAINTENANCE, FILE, and
DIAGNOSIS menus and register them to the USER menu.
If you specify pages or items frequently used for the USER
menu, you can easily call and use them.
The following pages are included on the factory-set USER
menu:
Menu page
menu No.
<VF OUT>
<VF DETAIL>
<FOCUS ASSIST>
<VF DISPLAY>
<'!' IND>
<VF MARKER>
<CURSOR>
<ZEBRA>
<SWITCH ASSIGN1>
<SWITCH ASSIGN2>
<HEADSET MIC>
<SYSTEM FORMAT>
<SYNC-OUT>
<SDI OUT>
<ROM VERSION>
For the items on each page, see the corresponding source
menu page in the table in "Menu List" (page 25).
USER Source menu / page No.
U01 OPERATION
U02 OPERATION
U03 OPERATION
U04 OPERATION
U05 OPERATION
U06 OPERATION
U07 OPERATION
U08 OPERATION
U09 OPERATION
U10 OPERATION
U11 OPERATION
U12 MAINTENANCE
U13 MAINTENANCE
U14 MAINTENANCE
U15 DIAGNOSIS
The USER MENU CUSTOMIZE menu allows you to configure
a USER menu that consists only of pages and items that you
need, by your adding, deleting or replacing pages.
Editing by items
The USER MENU CUSTOMIZE menu allows you to add a
new page to the USER menu and add desired items to the
page.
While the EDIT page contains factory-preset items, the USER
1 EDIT to USER 19 EDIT pages are all blank in their initial
state. You can register up to 10 items, including blank lines, on
each of these pages.
To add items to a page
Proceed as follows.
1
Set the DISPLAY switch from OFF to MENU while
holding the MENU SEL knob/ENTER button pressed.
The TOP MENU screen appears.
2
Turn the MENU SEL knob/ENTER button to move the
arrow marker (,) to USER MENU CUSTOMIZE, then
press the MENU SEL knob/ENTER button.
If this is the first time the USER MENU CUSTOMIZE
menu has been displayed, the CONTENTS page of the
menu appears.
If the USER MENU CUSTOMIZE menu has been used
before, the page last accessed appears.
3
If the CONTENTS page is displayed, turn the MENU
SEL knob/ENTER button to move the arrow marker
(,) to any of USER 1 EDIT to USER 19 EDIT, then
press the MENU SEL knob/ENTER button to display
14
the page.
04
If a different page is displayed, turn the MENU SEL
08
knob/ENTER button until the desired page appears,
then press the MENU SEL knob/ENTER button to
01
select the page.
02
Example: When you select the USER 2 EDIT page
03
11
10
16
17
20
M09
M10
4
Move the arrow marker (,) to the item to be added
M11
(this operation is unnecessary if no item exists on the
D03
page, as shown in the figure for step 3), then press the
MENU SEL knob/ENTER button.
The EDIT FUNCTION screen appears.
22
CONTENTS E00 TOP
xx
01.EDIT PAGE
02.USER 1 EDIT
c
03.USER 2 EDIT
04.USER 3 EDIT
05.USER 4 EDIT
06.USER 5 EDIT
07.USER 6 EDIT
08.USER 7 EDIT
09.USER 8 EDIT
10.USER 9 EDIT
USER 2 EDIT E03 TOP
c