Table of Contents
Advertisement
value cannot be obtained, depending on the shooting
environment.
2) Normally, the optimum offset is automatically set in conjunction
with the AREA MARKER SIZE and MASTER GAIN set values.
Use this setting when the optimum offset cannot be obtained,
depending on the shooting environment.
To use the area marker
Setting AREA MARKER to ON displays the detection area
of the focus as a marker on the viewfinder screen.
You can set the size and position of the detection area
with the menu items below.
SIZE: Changes the detection area size. (If the area size is
too large, both the subject and the background are
included in the area, making the indicator display
susceptible to deviate from the subject.)
POSITION: Roughly set the position of the detection area.
POSITION H: Finely adjust the position of the detection
area in the horizontal direction.
POSITION V: Finely adjust the position of the detection
area in the vertical direction.
4
Turn the MENU SEL knob/ENTER button to display
the desired setting and press the MENU SEL knob/
ENTER button.
5
To finish the adjustment, set the DISPLAY switch to
OFF to exit Menu mode.
Notes
• The level indicator and the effect area marker cannot be
displayed simultaneously. Whichever you set to ON last is
preferentially displayed.
• The area marker and the aspect safety marker cannot be
displayed simultaneously Whichever you set to ON last is
preferentially displayed.
• When displaying the focus assist indicators, check that the
flange focal length has been precisely adjusted.
For details about the flange focal length, see "Adjusting the
Flange Focal Length" (page 9).
Setting the Dynamic Focus Function
Detail
This sets the detail of the dynamic focus indicator.
The dynamic focus function is enabled when shooting in 8K.
The dynamic focus function adds a marking indicator, derived
from the luminance signal and color signal, to the area where
8K resolution signal is being output. This is used for effectively
displaying the 8K image focus point.
1
Display the CONTENTS page of the OPERATION
menu (referring to steps 1 to 4 in "Adding the VF
detail signal").
2
Turn the MENU SEL knob/ENTER button to align the
arrow marker (,) to <DYNAMIC FOCUS> and press
the MENU SEL knob/ENTER button.
The <DYNAMIC FOCUS> page is displayed.
<DYNAMIC FOCUS>
DYNAMIC FOCUS: OFF
FREQUENCY
ZOOM LINK
CRISP
LEVEL
PEAK COLOR
THRESHOLD
COLOR LEVEL
AREA
3
Turn the MENU SEL knob/ENTER button to align the
arrow marker (,) to the item to be set and press the
MENU SEL knob/ENTER button.
To use dynamic focus
Setting DYNAMIC FOCUS on the <VF DETAIL> page or
this page to ON displays markings of the luminance and
color signals in the regions where 8K resolution image is
being obtained.
You can set the marking detail with the menu items below.
FREQUENCY: Set the bandwidth of the 8K resolution
high-frequency signal to detect to one of four options.
It is set to (AUTO) when ZOOM LINK is ON.
ZOOM LINK: Automatically adjusts the dynamic focus
function to appropriate characteristics according to
the zoom position. Four modes are available for
selection to match the lens being used. It also sets
the level at the WIDE position mark.
CRISP: Adjust to eliminate fine portions of the detail
signal.
LEVEL: Set the brightness level of the marking signal to
add.
PEAK COLOR: Set the color added to the marking
indicator where the detected value exceeds a fixed
level.
THRESHOLD: Set the threshold value for displaying
PEAK COLOR.
COLOR LEVEL: Set the saturation of the color of the
PEAK COLOR indicator.
AREA: To limit the area where to display the dynamic
focus signal. The AREA value setting is common to
the VF detail, dynamic focus, and gritty focus
functions.
4
Turn the MENU SEL knob/ENTER button to display
the desired setting and press the MENU SEL knob/
ENTER button.
5
To finish the adjustment, set the DISPLAY switch to
OFF to exit Menu mode.
Setting the Gritty Focus Function
The gritty focus function emphasizes the focus point in VF
signals created from 8K resolution image signals.
1
Display the FOCUS ASSIST2 page of the OPERATION
menu.
2
Turn the MENU SEL knob/ENTER button to align the
arrow marker (,) to <GRITTY FOCUS> and set it to
ON.
You can set the details using the following items.
AREA: Limit the area to where the gritty focus is
displayed. The AREA value setting is common to the
VF detail, dynamic focus, and gritty focus functions.
16
05 TOP
: EXTRA-LOW
: OFF MODE1 100%
:
6%
: LOW
: YELLOW
:
50%
:
19%
: 100% H:0 V:0
Advertisement
Table of Contents
