Setting The Vf Dynamic Contract Function - Sony HDC1700 Operation Manual

NEAR LIMIT: Sets the NEAR edge of the focus position
meter.
FAR LIMIT: Sets the FAR edge of the focus position
meter.
The focus position range to display varies depending on
the NEAR LIMIT and FAR LIMIT settings. The full range is
displayed by setting NEAR LIMIT to 0 and FAR LIMIT to
999.
DIRECTION: Selects whether to display the meter
horizontally at the top of the screen or vertically on
the right edge of the screen.
SIZE: Sets the size of the meter.
RULED LINE: Turns the display of guide lines on the
meter on/off.
INDEX COLOR: Sets the color of the index.
INDEX WIDTH: Sets the width of the index.
MARKER WIDTH: Sets the width of the marker.
To set the adjustment sensitivity and display content
You can set the adjustment sensitivity and configure the
display in the adjusted state using ADJUSTED SIGN on
the <FOCUS POSITION METER2> page.
SENSE: Sets the adjustment sensitivity. Increasing the
value increases the sensitivity (making
determination of adjusted state more precise).
NAME DISP: Turns the display of the marker name in the
adjusted state on/off (DISPLAY screen only).
FRAME DISP: Turns the display of a color frame
(adjustment frame) on the screen in the adjusted
state on/off.
FRAME WIDTH: Sets the width of the adjustment frame.
To configure the marker display settings
You can set the marker display using MARKER CONFIG
on the <FOCUS POSITION METER2> page.
REG: Registers a marker at the index position.
DISP: Turns the marker display on/off.
COLOR: Sets the color of the marker. This also sets the
color of the adjustment frame.
NAME: Sets the name of the marker.
POS: Adjusts the marker position manually.
4
Turn the MENU SEL knob/ENTER button to display
the desired setting and press the MENU SEL knob/
ENTER button.
5
To finish the adjustment, set the DISPLAY switch to
OFF to exit Menu mode.
Marker registration
When HDLA is attached, you can register a marker for the focus
position meter using the VF OUT switch. Marker 1 is registered
using the R switch, marker 2 by the G switch, and marker 3 by
the B switch. Setting a switch to ON registers a marker at the
current index position (same function as REG on the <FOCUS
POSITION METER2> page). Setting a switch to OFF turns the
marker display off (same as setting DISP on the <FOCUS
POSITION METER2> page to OFF).
To register a marker for the focus position meter
using the VF OUT switch
Set VF OUT SW to FOCUS POSITION METER on the
<SWITCH ASSIGN1> page in the OPERATION menu.
Setting the VF Dynamic Contract
Function
Emphasizing the contrast in the image on the viewfinder
screen makes it easier to check the focusing condition for high
brightness areas and for subjects with low contrast levels.
The function of ON/OFF can also be operated via the switches
on the back panel.
1
Turn on the camera.
2
Set the DISPLAY switch to MENU while holding the
MENU SEL knob/ENTER button pressed.
The camera enters Menu mode, and "TOP" is displayed at
the upper right corner of the screen.
3
Rotate the MENU SEL knob/ENTER button to align the
arrow marker ( ) to "TOP" and push on the MENU
,
SEL knob/ENTER button.
The TOP MENU screen is displayed.
<TOP MENU>
USER
USER MENU CUSTOMIZE
ALL
OPERATION
PAINT
MAINTENANCE
FILE
DIAGNOSIS
4
Rotate the MENU SEL knob/ENTER button to align the
arrow marker ( ) to OPERATION and push on the
,
MENU SEL knob/ENTER button.
The CONTENTS page of the OPERATION menu is
displayed.
CONTENTS
01.<VF DISPLAY>
02.<'!'IND>
03.<VF MARKER>
04.<VF DETAIL>
05.<FOCUS POSITION METER1
06.<FOCUS POSITION METER2
07.<FOCUS ASSIST>
08.<VF DYNAMIC CONTRAST>
09.<ZEBRA>
10.<CURSOR>
5
Rotate the MENU SEL knob/ENTER button to align the
arrow marker ( ) to <VF DYNAMIC CONTRAST> and
,
push on the MENU SEL knob/ENTER button.
The <VF DYNAMIC CONTRAST> page is displayed.
<VF DYNAMIC CONTRAST>
DYNAMIC CONTRAST: OFF
GAIN
FILTER
MODE
22
00 TOP
08 TOP
: 0%
: WIDE
: HIGHLIGHT