Sony RM-PP1 Installation Manual
Sony RM-PP1 Installation Manual

Sony RM-PP1 Installation Manual

Program play box
Hide thumbs Also See for RM-PP1:

Advertisement

Quick Links

PROGRAM PLAY BOX
RM-PP1
INSTALLATION MANUAL
1st Edition
Serial No. 10001 and Higher

Advertisement

Table of Contents
loading

Summary of Contents for Sony RM-PP1

  • Page 1 PROGRAM PLAY BOX RM-PP1 INSTALLATION MANUAL 1st Edition Serial No. 10001 and Higher...
  • Page 2 4. Prevention against achieving hazardous condition due to uneven mechanical loading When this product is installed in a rack, please make sure that the rack does not achieve hazardous condition due to uneven mechanical loading. RM-PP1...
  • Page 3: Table Of Contents

    Voltage and Power Requirements ..........1-1 1-3-2. Recomended Power Cord ............1-1 1-4. Installation Space ..................1-2 1-5. Rack Mounting .................... 1-3 1-6. Connections and Setup ................1-7 1-7. Matching Connectors and Cables ..............1-8 1-8. Signal Inputs and Outputs ................1-9 RM-PP1...
  • Page 4: Manual Structure

    Manual Structure Purpose of this manual This manual is the installation manual of Program Play Box RM-PP1. This manual is intended for use by trained system and service engineers, and provides the information that is required to hardware install (environment, rack mounting, connection information, etc.).
  • Page 5: Installation

    Do not block the ventilation holes of the cabinet and the This unit does not come with a power cord. front and rear panels. To get a power cord, please contact your local Sony Sales Office/Service Center. Operating temperature: 5dC to 40dC...
  • Page 6: Installation Space

    . Leave more than 20 centimeters of space in the rear of the unit to secure the operation area. Mass : 8 kg 55.1 555.7 83.7 42.7 28.6 101.6 404.8 581(Maximum traveling distance) n Remove the feet when rack mounting. Unit : mm Dimensions when Rack-Mounting RM-PP1...
  • Page 7: Rack Mounting

    . Supplied with the RM-PP1 Distance to the center of the side rail Screws (B4 x 8) ........... 8 Height of the unit mounted in a rack Unit : mm The RM-PP1 contains ten screws, but the two screws of them are spare. RM-PP1...
  • Page 8 Inner rail Rack angle Polyamide washers Keep these screws and the feet. When operating the unit after demounting it from the rack, be sure to reattach the feet. Tightening torque: 80 x 10 N.m {8 kgf.cm} B4 x 8 RM-PP1...
  • Page 9 Rack B5 x 8 B5 x 8 12.7 Rack 2 pcs 2 pcs 31.75 Width: A = A' = 424 mm 12.7 Rail 31.75 Adjust B5 x 8 Front bracket 12.7 B5 x 8 Rear bracket Unit : mm RM-PP1...
  • Page 10 16. Slowly push the unit into the rack while pressing each Ornamental washers stopper . Be careful not to catch your finger or hand in rack RK5 x 20 mount rail. RK5 x 20 Ornamental washers Stopper Intermediate rail Stopper Inner rail RM-PP1...
  • Page 11: Connections And Setup

    Microsoft Windows 2000 Microsoft Windows 98 Second Edition CPU: 500 MHz or higher Memory: Minimum 128 MB Hard disk: Minimum 20 MB of available hard disk space Drive: CD-ROM XGA video display, Capable of 1024 x 768 resolution Display: RM-PP1...
  • Page 12: Matching Connectors And Cables

    1-7. Matching Connectors and Cables When external cables are connected to the connector of this unit, the hardware listed below (or equiva- lents) must be used. Panel indication Matching connector (cable) Sony part No. REF IN BNC 75Z, MALE (*1) 1-569-370-12 SDI IN,...
  • Page 13: Signal Inputs And Outputs

    0.3 V p-p, 75 Z, sync negative Output connectors 2 SDI OUT BNC x 2 Serial digital interface (270 M bps) Complies with SMPTE 259M and ITU-R BT.656 8 TC OUT XLR3-pin x 1 Time code 2.2 V p-p, low impedance, balanced RM-PP1...
  • Page 14 RXD ; Received Data (Input) TXD ; Transmitted Data (Output) DTR ; Data Terminal Ready (Output) SG ; Signal Ground DSR ; Data Set Ready (Input) RTS ; Request to Send (Output) CTS ; Clear to Send (Input) 1-10 RM-PP1...
  • Page 15 : The material contained in this manual consists of information that is the property of Sony Corporation. Check the metal trim, “metallized” knobs, screws, Sony Corporation expressly prohibits the duplication of...
  • Page 16 Printed in Japan Sony Corporation RM-PP1 (UC) E 2003. 6 08 3-775-784-01 (1) B&P Company ©2002...

Table of Contents