Table of Contents
Advertisement
USE GENUINE GRACO PARTS AND ACCESSORIES
Must be purchased separately .
GROUNDING CLAMP 103–538
GROUND WIRE 208–950
25 ft (7.6 m) long, 12 gauge (1.5 mm )
AIR LINE LUBRICATOR
250 psi (17.5 bar) MAXIMUM WORKING PRESSURE
214–848 1/2 npt inlet and outlet
214–849 3/4 npt inlet and outlet
AIR LINE FILTER
250 psi (17.5 bar) MAXIMUM WORKING PRESSURE
106–149 1/2 npt inlet and outlet
106–150 3/4 npt inlet and outlet
GROUNDED BUNA–N AIR SUPPLY HOSE
175 psi (12 bar) MAXIMUM WORKING PRESSURE
Part No.
ID
205–418
1/2" (13 mm)
205–216
1/2" (13 mm)
205–273
1/2" (13 mm)
208–594
1/2" (13 mm)
BACK PRESSURE REGULATOR 206–819
3000 psi (210 bar) MAXIMUM WORKING PRESSURE
Use in circulating system fluid return line to regulate back
pressure to gun and maintain proper circulating pres-
sure.
FLUID PRESSURE REGULATOR 206–661
3000 psi (210 bar) MAXIMUM WORKING PRESSURE
Use at each gun drop in multiple gun systems, to regulate
fluid pressure to each gun.
ACCESSORIES
Length
Thd. Size
6 ft (1.8 m)
1/2 npt(m)
15 ft (4.5 m)
1/2 npt(m)
25 ft (7.6 m)
1/2 npt(m)
50 ft (15 m)
1/2 npt(m)
GROUNDED NYLON FLUID HOSE
3000 psi (210 bar) MAXIMUM WORKING PRESSURE
Part No.
ID
214–700
3/16" (4.8 mm)
214–701
3/16" (4.8 mm)
210–540
1/4" (6.4 mm)
210–541
1/4" (6.4 mm)
214–703
3/8" (9.5 mm)
214–705
3/8" (9.5 mm)
214–920
3/8" (9.5 mm)
STAINLESS STEEL AIRLESS SPRAY GUN
5000 psi (350 bar) MAXIMUM WORKING PRESSURE
208–327
.037" orifice, 2–finger trigger
208–663
.090" orifice, 2–finger trigger
208–664
.090" orifice, 4–finger trigger
220–954
.090" orifice, 2–finger trigger, RAC
Less
tip guard
VISCON FLUID HEATER 220–522
4000 psi (276 bar) MAXIMUM WORKING PRESSURE
Reduces fluid viscosity for easier spraying. 120 V, sing-
le–phase, 16.7 Amp. Stainless steel. Refer to Instruction
Manual 307–805.
WARNING: Not for use in hazardous areas containing
flammable materials or fumes.
INSULATED HOSE KIT 222–263
3000 psi (210 bar) MAXIMUM WORKING PRESSURE
25 ft. (7.6 m) nylon fluid hose for use with heated sys-
tems. Includes in–line fluid filter, circulating manifold, and
3 ft. (0.9 m) whip hose.
HEATER CONVERSION KITS
Use to convert pump Models 224–625 and 231–163 to a
heated circulating spray system. See pages 16–18 for
parts. The Viscon Heater 220–522 and Insulated Hose
Kit 222–263 are also required, and must be ordered sep-
arately (see above).
222–262
Heater Mounting Kit
222–261
Circulating Kit
SST PIPE SEALANT 110–110
Apply to all non–swiveling pipe connections.
6 ml supply.
Length
Thd. Size
2 ft (610 mm)
1/4 npsm
(fbe) swivel
3 ft (914 mm)
1/4 npt(m)
x 1/4
npsm(f)
swivel
25 ft (7.6 m)
1/4 npsm
(fbe) swivel
50 ft (15.2 m)
1/4 npsm
(fbe) swivel
25 ft (7.6 m)
3/8 npt
(mbe)
50 ft (15.2 m)
3/8 npt
(mbe)
100 ft (30.4 m)
3/8 npt
(mbe)
IV Drip-
Advertisement
Table of Contents
