Osram OTi30W Installation And Troubleshooting Manual
  1. Manuals
  2. Brands
  3. Osram Manuals
  4. Lighting Equipment
  5. OTi30W
  6. Installation and troubleshooting manual

Osram OTi30W Installation And Troubleshooting Manual

Self test slim emergency driver
Hide thumbs
1
2
3
4
5
6
7
Table of Contents

Advertisement

Quick Links

Download this manual
OTi30W Self Test Slim Emergency Driver
Installation and Troubleshooting Guide - PN: 57414
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. This product is for use with an LED lighting load and supplies up to 10W of power at factory
programmed current with a voltage between 10.0 VDC and 55.0 VDC in emergency mode for
a minimum of 90 minutes.
2. Make sure all connections are in accordance with the National Electrical Code, Canadian
Electrical Code and any local regulations.
3. To reduce the risk of electric shock, disconnect AC power of the emergency driver and fuse
from fuse holder of the battery pack before servicing.
4. This emergency driver is suitable for factory and field installation. For field installation, please
see the instructions on page
5. This product is suitable for damp locations where the
and battery pack case temperature is 55°C maximum.
6. Do not use for outdoor applications.
7. Product is not suitable for heated air outlets and wet or hazardous locations.
8. Do not install near gas or electric heaters.
9. The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition.
10. Do not use this product for other than intended use.
11.
Equipment should be mounted in locations and at heights where it will not readily be subjected
to tampering by unauthorized personnel.
12. Servicing should be performed by qualified service personnel.
13. Use caution when servicing batteries.
THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM
BATTERY. THE BATTERY MUST BE RECYCLED OR DISPOSED
IMPORTANT SAFEGUARDS
3.
SAVE THESE INSTRUCTION
PROPERLY.
driver case temperature is 75°C maximum

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OTi30W and is the answer not in the manual?

Questions and answers

Related Manuals for Osram OTi30W

Summary of Contents for Osram OTi30W

  • Page 1: Important Safeguards

    OTi30W Self Test Slim Emergency Driver Installation and Troubleshooting Guide - PN: 57414 IMPORTANT SAFEGUARDS WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. This product is for use with an LED lighting load and supplies up to 10W of power at factory programmed current with a voltage between 10.0 VDC and 55.0 VDC in emergency mode for...
  • Page 2 90 minutes. Self-Testing Operation The OSRAM self-testing emergency driver unit contains a control/monitor circuit that automatically performs a 30-second discharge test once a month and a full 90-minute discharge test once a year.

  • Page 3: Installation Instructions

    Please refer to the product specification for the exact range. For more information on programming instructions, please refer to www.osram.us 4. The emergency mode power should be less than or equal to rating of the driver and the battery pack that is being used for the application.
  • Page 4 verify that the total forward voltage is within the limits of this product. Using a voltage meter, it may be possible to directly measure the voltage across the LED arrays when operating from the emergency driver. 6. Ensure there will be sufficient light output in the end application. Estimate the egress lighting illumination levels by doing the following: a.
  • Page 5 STEP 2: INSTALLING THE TEST SWITCH ON FIXTURE SURFACE  Mount the supplied 3-wire illuminated test switch in a location that is visible and accessible by maintenance personnel.  The switch mounts through a mounting hole which may need to be made in the luminaire or could come pre-punched by the luminaire supplier.
  • Page 6 Figure 4: Wiring diagram for switched line 10/2018...

  • Page 7: Troubleshooting Guide

    Check LED load is operational and specified for emergency driver application OSRAM SYLVANIA Inc. 200 Ballardvale Street Wilmington, MA 01887 USA 1-877-636-5267 www.osram.us/ds ECS-352 OSRAM and OPTOTRONIC are registered trademarks of OSRAM GmbH. Specifications subject to change without notice. © 2018 OSRAM SYLVANIA Inc. 10/2018...

Table of Contents