Table of Contents
Advertisement
Quick Links
Page
Contents
2
1.
3
2.
4
3.
4
4
5
5
7
4.
7
8
9
14
16
17
17
18
5.
AXCOR WASH 600
AXCOR WASH 600 HC
INSTRUCTION MANUAL
INDEX
Congratulations on choosing a Claypaky product
We thank you for your custom.
Please note that this product, as all the others in the
rich Claypaky range, has been designed and made with
total quality to ensure excellent performance and best
meet your expectations and requirements.
CL3000
CL3001
Advertisement
Table of Contents
Related Manuals for Osram CLAYPAKY AXCOR WASH 600
Summary of Contents for Osram CLAYPAKY AXCOR WASH 600
-
Page 1: Table Of Contents
AXCOR WASH 600 CL3000 AXCOR WASH 600 HC CL3001 INSTRUCTION MANUAL INDEX Congratulations on choosing a Claypaky product Page Contents We thank you for your custom. Safety information Please note that this product, as all the others in the rich Claypaky range, has been designed and made with Unpacking and preparation total quality to ensure excellent performance and best Installation and start-up... -
Page 2: Safety Information
1. SAFETY INFORMATION SAFETY INFORMATION IMPORTANT: Claypaky recommends you carefully read and keep the safety information on this product, also available in digital format at the following link: www.claypaky.com Ref: FIS00W - Safety Information Axcor 600 series INFORMAZIONI DI SICUREZZA IMPORTANTE: Claypaky raccomanda di leggere accuratamente e conservare le informazioni di sicurezza relative a questo prodotto, sempre reperibili in versione digitale al seguente link: www.claypaky.com... -
Page 3: Unpacking And Preparation
2. UNPACKING AND PREPARATION 2 x 183102/805 Packing contents - Fig. 1 LOCKED UNLOCKED PAN Mechanism Lock and Release (every 90°) - Fig. 2 TILT Mechanism Lock and Release (every 45°) - Fig. 3 AXCOR WASH 600 600 HC... -
Page 4: Installation And Start-Up
3. INSTALLATION AND START-UP 3.1 Installing the fixture Installing the projector - Fig. 4 The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall. WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. Cod. 105041/001 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base. -
Page 5: Connecting The Control Signal Line: Dmx / Art-Net
Mains Connecting to the mains supply - Fig. 6 3.3 Connecting the control signal line: DMX / Art-Net DMX 512 3 PIN SIGNAL SCREEN SIGNAL DMX 512 5 PIN SCREEN SIGNAL SIGNAL Connecting to the control signal line (DMX) - Fig. 7 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. - Page 6 Reversal of the display - Fig. 9 To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Setting the projector starting address On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
-
Page 7: Maintenance
4. MAINTENANCE 4.1 Opening the covers 1/4 Turn 1/4 Turn 1/4 Turn CLICK!! Locking and releasing Pan and Tilt movements - Refer to the instructions in the UNPACKING AND PREPARATION section. Opening the head covers - Fig. 10. Closing the head covers - Fig. 11. Continue AXCOR WASH 600 600 HC... -
Page 8: Periodical Cleaning
4.2 Periodical cleaning Upper side NOTE: keep a careful cleaning of the ''CMY/colour filters assembly'' to prevent rapid deterioration. Light collimation system This product contains internal light collimation system. Avoid intense light from any angle. Periodical cleaning - Fig. 12 To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. -
Page 9: Effects Module Removal
4.3 Effects module removal Upper side Extraction of the effect modules: Preliminary operations - Fig. 13. NOTE: - Do not disconnect wiring harnesses when the fixtures is switched-on, to avoid to damage electronic boards. - Do not switch-on the fixtures with wiring harness disconnected. Continue AXCOR WASH 600 600 HC... - Page 10 Upper side Lower side Extraction of the effect modules: Preliminary operations - Fig. 14. NOTE: - Do not disconnect wiring harnesses when the fixtures is switched-on, to avoid to damage electronic boards. - Do not switch-on the fixtures with wiring harness disconnected. AXCOR WASH 600 600 HC...
- Page 11 Upper side Extraction of the effect modules - Fig. 15. IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 15, 16, 17 and 18 in reverse order. Continue AXCOR WASH 600 600 HC...
- Page 12 Upper side Extraction of the effect modules - Fig. 16. IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 15, 16, 17 and 18 in reverse order. AXCOR WASH 600 600 HC...
- Page 13 Upper side Extraction of the effect modules - Fig. 17. IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 15, 16, 17 and 18 in reverse order. Continue AXCOR WASH 600 600 HC...
-
Page 14: Cleaning Of The Filters
4.4 - Cleaning of the filters 1/4 Turn Cleaning of the filters - Fig. 18. AXCOR WASH 600 600 HC... - Page 15 1/4 Turn Cleaning of the filters - Fig. 19. Continue AXCOR WASH 600 600 HC...
-
Page 16: Battery Removal
4.5 Battery removal This product contains a rechargeable battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. AXCOR WASH 600 600 HC... -
Page 17: Frost Filter Removal
4.6 - Frost filter removal Frost filter removal - Fig. 24. 4.7 - Accessories CZ1000 - Fresnel Lens Kit CZ1001 - Clear Lens Kit Accessories - Fig. 25. AXCOR WASH 600 600 HC... -
Page 18: Specifications
5. SPECIFICATIONS (24.45") (22.76") (31.18") (16.10") (25.04") (12.95") (15.28") POWER SUPPLIES • DMX level monitoring on all channels. • Max temperature of the external surface 90°C AC power input 100-240V, 50/60 Hz. • Internal data transmission diagnostics. (194°F). • Upgrade with no power (CPU only) firmware •... - Page 19 AXCOR WASH 600 600 HC...
- Page 20 Clay Paky - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.com S.p.A.
Need help?
Do you have a question about the CLAYPAKY AXCOR WASH 600 and is the answer not in the manual?
Questions and answers