Table of Contents
Advertisement
Quick Links
Touch Control Installation Instructions
Product View ................................................................................................................................................................. 1
Tools and Fasteners Needed ........................................................................................................................................ 2
INSTALLATION
Installation Overview .................................................................................................................................................... 3
STEP 1: Mount the Installation Brackets ................................................................................................................... 3
Inside Mount .............................................................................................................................................................. 4
Outside Mount ........................................................................................................................................................... 5
End Mount .................................................................................................................................................................. 6
STEP 2: Mount he Battery Wand and Connect the Power Cable, If Applicable .................................................... 7
STEP 3: Install the Shading ......................................................................................................................................... 7
STEP 4: Connect the Power Source ........................................................................................................................... 8
Attach Magnetic Hold-Down Brackets (Optional) .................................................................................................. 11
OPERATION
Basic Operation ........................................................................................................................................................... 12
Troubleshooting .......................................................................................................................................................... 13
Removing the Shading, If Necessary ......................................................................................................................... 16
Cleaning Procedures ................................................................................................................................................... 17
.................................................................................................................................................................. 18
Shadings Collection
Rev. A
9/3/19
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kirsch Shadings Series
Summary of Contents for Kirsch Shadings Series
-
Page 1: Table Of Contents
Shadings Collection Touch Control Installation Instructions GETTING STARTED Product View ................................. 1 Tools and Fasteners Needed ............................2 INSTALLATION Installation Overview ..............................3 STEP 1: Mount the Installation Brackets ........................3 Inside Mount ................................4 Outside Mount ................................5 End Mount .................................. 6 STEP 2: Mount he Battery Wand and Connect the Power Cable, If Applicable ............ -
Page 2: Getting Started
GETTING STARTED Product View Battery Wand Battery Wand Clips Power Cable Installation Brackets Activation Limit Stops Wand Magnetic Hold-Down Brackets Weight (Optional) Bottom Rail Clip Balance Weight Weight Clip... -
Page 3: Tools And Fasteners Needed
GETTING STARTED ® Thank you for purchasing the Kirsch Shadings Collection. With proper installation, operation, and care, your new shades will provide years of beauty and performance. Please thoroughly review this instruction booklet and the enclosed packing list before beginning the installation. If your shading has a protective cover on the fabric-covered headrail, keep the plastic in place until the shading is installed. -
Page 4: Installation Overview
INSTALLATION INSTALLATION Installation Overview To install your shading, you will need to perform the following four steps: STEP 1: Mount the Installation Brackets STEP 2: Mount the Battery Wand and Connect the Power Cable, If Applicable STEP 3: Install the Shading STEP 4: Connect the Power Source, If Applicable STEP 1: Mount the Installation Brackets Your order will include the correct number of installation brackets for your shading width, as shown in the table below. -
Page 5: Inside Mount
INSTALLATION INSTALLATION Mount the Installation Brackets — Inside Mount Back Cover Bracket Prepare the Installation Brackets Top Tab The purpose of the back cover bracket is to provide an attachment for the optional back cover. The top tab ensures that there is clearance for the battery wand. Back Cover Slots Bottom Tab... -
Page 6: Outside Mount
INSTALLATION INSTALLATION Mount the Installation Brackets — Outside Mount Mount the Installation Brackets Center the headrail over the window opening at the desired height. Use a pencil to lightly mark each end of the headrail. ■ ■ Alternatively, measure the width of the headrail and use that width to mark the headrail end points over the window ➤... -
Page 7: End Mount
INSTALLATION INSTALLATION If using extension brackets, attach an installation bracket to the underside of each extension bracket ■ ■ Speed Nut using the speed nuts and screws provided. Screw Back Cover Bracket Top Tab Proceed to ”STEP 2: Mount the Battery Wand and Connect the Power Cable, If Applicable” on page 7. Back Cover Mount the Installation Brackets —... -
Page 8: Step 2: Mount He Battery Wand And Connect The Power Cable, If Applicable
INSTALLATION INSTALLATION STEP 2: Mount the Battery Wand and Connect the Power Cable, If Applicable For an optional satellite battery pack, 18V DC Power Supply, 18V DC Power Supply with daisy-chain connections, or C-size satellite battery wand, the power source will be connected after the shading is installed. Battery Wand Install the Battery Wand Clips Attach the battery wand clips to the headrail. -
Page 9: Step 4: Connect The Power Source
INSTALLATION INSTALLATION Mount the Headrail Peel back the protective covering from the top of the fabric-covered headrail. Leave the rest of the protective covering on the ■ ■ front of the headrail. Position the shading so that the front faces you. ■... - Page 10 INSTALLATION INSTALLATION Satellite Battery Pack Mount the Satellite Battery Pack Decide where you want to mount the satellite battery pack. A satellite battery pack may be mounted in any orientation. ■ ■ Mark the screw holes for the wall mount bracket. ■...
- Page 11 INSTALLATION INSTALLATION 18V DC Power Supply with Daisy-Chain Connections The daisy-chain feature allows up to three Automation shadings to be powered by a single 18V DC Power Supply. However, each shading can operate independently. The daisy-chain feature is only available with the 18V DC Power Supply option. Route the power cables from each shading to the connector, using the extension cable, if necessary.
-
Page 12: Attach Magnetic Hold-Down Brackets (Optional)
INSTALLATION INSTALLATION Attach Magnetic Hold-Down Brackets (Optional) Lower the shading, keeping the vanes closed. ■ ■ Place the magnetic hold-down brackets onto the bottom rail just inside the end caps, oriented as shown. ■ ■ Hold the brackets while opening and closing the vanes. (It may be necessary to have someone assist you.) ■... -
Page 13: Basic Operation
INSTALLATION OPERATION Basic Operation To Lower the Shading Briefly pull the wand down to move the shading in the down/closed position. ■ ■ The shading will move to the fully closed position. ■ ■ Lower Shading To Open the Vanes With the shading fully lowered, briefly pull the wand down to open the vanes. -
Page 14: Troubleshooting
If your shading is not operating correctly: Refer to the following troubleshooting procedures for specific solutions for your shading. ■ ■ ® For questions, please contract Kirsch at 844-KIRSCH2 (844-547-7242). Problem The shading will not fit into the installation brackets. - Page 15 INSTALLATION OPERATION Problem The shading raises from the sill when the vanes are closed. Solution A small gap between the sill and the bottom of the shading is normal in the fully lowered “vane closed” position. The gap is necessary to allow for the unimpeded movement of the bottom rail. If this distance is excessive or moves over time, see “Adjust the Vanes Open and Closed Limits”...
- Page 16 INSTALLATION OPERATION Problem The shading limits need to be adjusted. Solution Adjust the Vanes Open and Closed Limits Both limits must be set in sequential order when in programming mode. The mechanical limit is when the shading is at the maximum fully closed (down) position and the vanes have moved to the open position.
-
Page 17: Care
INSTALLATION OPERATION Problem The shading is hard to raise or lower, or the bottom rail does not stop at the top limit. Headrail Limit Stop Solution Check the adjustment position of both limit stops. The top illustration shows the correct adjustment. The limit stop catches the bottom rail, and the bottom of the limit stop is slightly above or barely touching the fabric roll. -
Page 18: Cleaning Procedures
INSTALLATION CARE Cleaning Procedures ® Kirsch Shadings are made of 100% polyester, which means they are inherently durable and resilient. However, care must be taken to avoid wrinkling the fabric, particularly where the vanes meet the facings. Fabric-Covered Headrail Spot-clean the headrail using a sponge or delicate cloth, cool distilled water and a mild soap solution; handle with care as you ■... -
Page 19: Warranty
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. © 2019 Kirsch Custom Window Coverings. All rights reserved. All trademarks used herein are the property of Kirsch or their respective owners. 09/19...
Need help?
Do you have a question about the Shadings Series and is the answer not in the manual?
Questions and answers