Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Keysight Technologies N1022B
Summary of Contents for Keysight Technologies N1022B
- Page 1 Keysight N1022B Active Probe Adapter User’s Guide...
- Page 2 Notices Warranty © Keysight Technologies, Inc. 2009 - 2014 (June 1987) or DFAR 252.227-7015 (b)(2) (November 1995), as applicable in any tech- No part of this manual may be reproduced in The material contained in this document is nical data.
-
Page 3: Table Of Contents
Contents Keysight N1022B Active Probe Adapter / 5 General Safety Considerations / 6 Installation Category / 7 Instrument Markings / 7 Using the Probe Adapter / 8 Available Accessories / 8 Cleaning / 8 Inspecting / 8 Connecting the N1022B / 9... - Page 4 Contents User’s Guide...
-
Page 5: Keysight N1022B Active Probe Adapter
A.03.05 or later be installed on the Infiniium DCA. The Infiniimax Active Probes include the 1131A, 1132A, and 1134A. Other supported active probes include the 1152A, 1156A, 1157A, and 1158A. When using the N1022B, always work at a static-safe work station and wear a wrist-strap CAUTION or heel-strap. -
Page 6: General Safety Considerations
No operator serviceable parts inside. Refer servicing to qualified personnel. To prevent electrical WARNING shock, do not remove covers. To prevent electrical shock, d isconnect the N1022B from probe power before cleaning. Use a dry cloth WARNING to clean the external case parts. Do not attempt to clean internally. -
Page 7: Installation Category
N1022B Probe Adapter Installation Category Installation Categories (overvoltage categories) are determined by the transient overvoltage levels that may be expected. CAT I: Mains isolated. CAT II: Line voltage in appliance and to wall outlet. CAT III: Line voltage behind wall outlet to next level of distribution. -
Page 8: Using The Probe Adapter
N1022B Probe Adapter Using the Probe Adapter There are a few things to consider when connecting the N1022B Active Probe Adapter to an active probe and the Infiniium DCA. - The dynamic range of the system will be 3.2V (6.4 Vp-p), which with probe offset, covers most digital technologies. -
Page 9: Connecting The N1022B
Be sure that the instrument is properly earth-grounded to prevent buildup of static charge. The N1022B can be directly connected to any 86100-series or 83480-series module with a 3.5 mm NOTE electrical channel input. - Page 10 However, the technologies necessary to achieve high performance do not allow the probe to be unbreakable. Treat the probe adapter with care. During operation, the N1022B probe adapter’s temperature may feel warm when you touch it. This is NOTE normal and does not indicate a problem.
- Page 11 N1022B Probe Adapter Figure 1 Probe Channel Dialog Box Perform the probe calibration procedure so that the DC gain, offset zero, and offset gain will be calibrated. You can access information about probe attenuation and probe calibration in the Infiniium DCA Help system.
-
Page 12: Static-Safe Workstation
N1022B Probe Adapter Static-Safe Workstation Electrostatic discharge (ESD) can damage or destroy electronic components. All work on electronic assemblies should be performed at a static-safe workstation. The following figure shows an example of a static-safe work station using two types of ESD protection: - Conductive table-mat and wrist-strap combination. - Page 13 N1022B Probe Adapter These techniques for a static-safe work station should not be used when working on circuitry with a WARNING vol tage potential greater than 500 vol ts. The following suggestions may help reduce ESD damage that occurs during testing and servicing operations.
-
Page 14: Specifications And Regulatory Information
N1022B Probe Adapter Specifications and Regulatory Information This section lists specifications and characteristics and regulatory information of the probe adapter. Specifications The distinction between specifications and characteristics is described as follows: ° - Specifications describe warranted performance over the temperature range 0 C to °... - Page 15 Weight 200 g (7 oz) max Dimensions (excludes power cable) Height 34 mm (1.34 in.) Weight 38 mm (1.50 in.) Length 61 mm (2.4 in.) Power Cable Length 200 mm (7.9 in.) from connector tip to N1022B body User’s Guide...
- Page 16 N1022B Probe Adapter Table 2 Performance Specifications Item Specification Frequency Range (Characteristic) 0 - 18 GHz Power Input +17V 225 mA –17V 225 mA Output Voltage +12V ±5% –12V ±5% V prog ±5% –V prog ±5% Output Current 0 - 200 mA (+12V) 0 - 200 mA (–12V)
-
Page 17: Regulatory Information
N1022B Probe Adapter Figure 3 N1022B I/O Connections Regulatory Information Electrostatic Discharge Immunity - IEC 61000-4-2: 1995 passes criterion B. This product complies with the Electrostatic Discharge immunity requirement in IEC/EN 61326 using performance criterion B. Degradation of some product specifications can occur during the instance of an electrostatic discharge. - Page 18 N1022B Probe Adapter Table 3 Notice for Germany: Noise Declaration Acoustic Noise Emission Geraeuschemission LpA < 70 dB LpA < 70 dB Operator position am Arbeitsplatz Normal position normaler Betrieb per ISO 7779 nach DIN 45635 t.19 User’s Guide...
-
Page 19: Service
N1022B Probe Adapter Service Service Keysightor the N1022B Active Probe Adapter is by replacement only. To order a new N1022B, contact your local Keysight Technologies Sales Office. Return the failed probe adapter to your local Keysight service center. If the probe adapter is still under warranty or is covered by an Keysight maintenance contract, it will be replaced under the terms of the warranty or contract. - Page 20 N1022B Probe Adapter Table 4 Probe Power Outputs Supply Power Output –3V Offset 5 and ring Probe ID –12V +12V User’s Guide...
-
Page 21: Returning The N1022B
N1022B Probe Adapter Returning the N1022B When the probe adapter is returned to an Keysight service office for servicing, it must be adequately packaged and have a complete description of the failure symptoms attached. Please notify the service office before returning your probe adapter for service. Any special arrangements for the adapter can be discussed at this time. - Page 22 N1022B Probe Adapter User’s Guide...
- Page 23 Index Index torque wrench, Accessories, CE mark, cleaning, CSA mark, dynamic range, EMC requirements, environmental specifications, ESD protection, ISM1-A, noise declaration, noise requirements, performance specifications, Probe Channel dialog box, probe power outputs, service, specifications environmental, performance, static-safe workstation, torque setting, User’s Guide...
- Page 24 Index User’s Guide...
Need help?
Do you have a question about the N1022B and is the answer not in the manual?
Questions and answers