Page 1
CAMERA ADAPTOR CA-950 CA-950P INSTALLATION AND MAINTENANCE MANUAL 1st Edition Serial No. 10001 and Higher: CA-950 (JN) Serial No. 40001 and Higher: CA-950P (CE)
Page 2
Laser output power : _8 dBm CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT This camera adaptor is classified as a CLASS 1 LASER PRODUCT. The CLASS 1 LASER PRODUCT label is located on the 68-pin connector panel. CA-950/950P IMM...
This manual describes the information items on maintenance, and items that premise the service based on the components parts such as alignment, schematic diagrams, board layouts and spare parts list. If this manual is required, please contact your local Sony Sales Office/Service Center. Part number: 9-968-571-XX (Volume 1) 9-968-572-XX (Volume 2) .
If ROM version is lower than the specified below, be sure to perform ROM replace- ment. (The ROM version of BVP-9500WS/9500WSP is already corresponding to CA-950/950P.) If ROM replacement is required, contact your local Sony Sales Office/Service Center. ROM version...
*2 : In connection with CCU IN (X) (DYNAMIC MIC) GND (PGM) INCOM _20 dBu RECEIVE OUT (with INCOM level control set to mechanical center) PGM 1/2 OUT _20 dBu (with PGM level control set to mechanical center) 1-2 (E) CA-950/950P IMM...
Page 7
DC (+) IN DC 10.5 V to 17 V DC OUT (4P FEMALE) (External view) No. Signal Specifications GND for UNREG No connection No connection UNREG +12 V OUT DC 10.5 V to 17 V, 500 mA (MAX) 1-3 (E) CA-950/950P IMM...
Page 8
G TALLY ON : GND OFF : High impedance No connection RX_DATA_IN (0) TRUNK DATA IN, RS232-C RX_DATA_IN (1) No connection No connection TX_DATA_OUT (0) TRUNK DATA OUT, RS232-C TX_DATA_OUT (1) (0 dBu = 0.775 Vrms) 1-4 (E) CA-950/950P IMM...
Page 9
IIC CLOCK IN (CA) 5 V p-p IIC DATA IN/OUT (CA) 5 V p-p, 4700 Z, Pull up IIC CLOCK IN (ST) 5 V p-p IIC DATA IN/OUT (ST) No connection (0 dBu = 0.775 Vrms) 1-5 (E) CA-950/950P IMM...
Page 10
27 MHz (G) GND for 27 MHz 27 MHz IN (X) 3.3 V p-p to 2.5 V p-p 18 MHz IN (G) GND for 18 MHz 18 MHz IN (X) 3.3 V p-p to 2.5 V p-p 1-6 (E) CA-950/950P IMM...
White Brown White Brown Brown 8P CONNECTOR(MALE) 8P CONNECTOR(MALE) (WIRING SIDE) (WIRING SIDE) REMOTE Cable (supplied with RM-B150) (Outer sheath color : Black) Black White White Brown White 8P CONNECTOR(MALE) 8P CONNECTOR(MALE) (WIRING SIDE) (WIRING SIDE) 1-7 (E) CA-950/950P IMM...
HIROSE HR10A-7P-4P equivalent TRACKER HIROSE HR25-9P-20P equivalent (20P FEMALE) *1: Use of REMOTE cable enables to monitor video signals. *2: If using a cable of length different from a standard product, consult your local Sony Sales Office/Service Center. 1-8 (E) CA-950/950P IMM...
Fixing posts B3 x 6 B3 x 8 Top panel B4 x 12 Connector Right side panel CN304 SERIAL OUT CN301 SERIAL IN B4 x 12 Left side panel B4 x 12 B4 x 12 SDI-30 board 1-10 (E) CA-950/950P IMM...
Sets ON or OFF the setup function of the return video signal to be output to VF or TEST OUT. ON: Setup of 7.5 IRE is available. OFF: Setup is unavailable. * : Only used for CA-950, not for CA-950P. 1-11 (E) CA-950/950P IMM...
When using AB POWERING +12 V microphone, set ON. When MIC POWER switch on the rear panel is set to OFF or +48 V, the power cannot be supplied even if this switch is turned ON. S301 MIC TEST Refer to the operation manual. 1-12 (E) CA-950/950P IMM...
Mixed signal of INCOM and PGM INCOM is output as INCOM and PGM INCOM outputs. INCOM level control knob adjusts mixed signal level of the INCOM and PGM, and PGM level control knob adjusts the balance between them. 1-13 (E) CA-950/950P IMM...
Page 18
PGM1/PGM2 switch S160-1 (Rear panel) (S246-1) PGM1 INCOM1 LEFT (RIGHT) OUT S160-2 PGM level control (S246-2) (Rear panel, Left side) S154-2 (S346-2) INCOM2 PGM2 LEFT (RIGHT) OUT S154-1 PGM level control (S346-1) (Rear panel, Right side) 1-14 (E) CA-950/950P IMM...
Page 19
*2: Volume is adjustable by a level control for each of TRACKER, PGM, ENG and PROD on the rear panel. PGM1/PGM2 switch S160-2 (Rear panel) (S246-2) PGM1 INCOM1 LEFT (RIGHT) OUT PGM level control (Rear panel) S154-2 (S346-2) INCOM2 PGM2 LEFT (RIGHT) OUT 1-15 (E) CA-950/950P IMM...
Page 20
CM/DYM (Panel) S624 GAIN (Panel) Refer to the operation manual. 0 (0 dB) S724 GAIN (Panel) Refer to the operation manual. 0 (0 dB) * : Only used for AU-273. For AU-273P, always set to OFF. 1-16 (E) CA-950/950P IMM...
Follow the procedures below for cleaning. Tools Required . Alignment sleeve remover HC-001 (for female connector) Sony P/N: J-6480-010-A Female connector Insert the shorter nose end when removing/installing the The optical contacts for female connector are in an unex- alignment sleeve.
3. Clean the tip of the white optical contacts by a cotton swab moistened with alcohol. Optical contacts (white) Top panel 1. Separate a CA-950/950P from the camera. 2. Remove the top panel. (Refer to Section 1-4.) 3. Clean off dust of the dustproof filters with a blower. Dustproof filters 4.
3-676-244-1X Rubber part RUBBER (EA), DROP 3-724-730-0X Rubber part PROTECTION CAP, CONNECTOR 3-605-338-0X Rubber part COVER (LARGE), SW 3-731-742-0X Rubber part CONNECTOR, COVER 3-187-015-0X Rubber part 6, 7, 8 MOTOR, FAN 1-698-236-3X Replace every two years 2-3 (E) CA-950/950P IMM...
Page 25
The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.
Need help?
Do you have a question about the CA-950 and is the answer not in the manual?
Questions and answers