Page 1
CAMERA ADAPTOR CA-755/755P MAINTENANCE MANUAL 1st Edition (Revised 1) Serial No. 10001 and Higher (UC) Serial No. 30001 and Higher (J) Serial No. 40001 and Higher (CE)
Page 2
! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
Page 3
Voor de klanten in Nederland CAUTION Dit apparaat bevat een MnO -Li batterij voor memory Danger of explosion if battery is incorrectly back-up. replaced. Raadpleeg uw leverancier over de verwijdering van de Replace only with the same or equivalent type recommended by the manufacturer.
Manual Structure Purpose of this manual This manual is the maintenance manual for Camera Adaptor CA-755/755P. This manual describes the information items on maintenance, and items that premise the service based on the components parts such as alignment, schematic diagram, board layout and spare parts list, assuming use of service engineers.
1-1. System Configuration 1-1-1. Confirmation before Connection 1-1-2. Power Supply When the CA-755/755P is to be connected to the following Power Voltage DC +12.0 V (DC +11.5 to +17.0 V) camcorders, be sure to check that the ROM version for IC16/AT-84 board of the camcorder is Ver.
AC ADAPTOR AC-550/550CE The servo filter unit BKDW-701 can be used only with a DVW-700 series camcorder which is connected to the CA-755/755P and is controlled by the CCU-550/700/700A (or their PAL model). As for installation, refer to installation and maintenance manual supplied with BKDW-701. The BKDW-701 cannot install in the DNW series.
DC (+) IN DC 11.5 to 17.0 V INCOM OUT (X) 1.7 V p-p MAX (1 kHz), 300 Z, Unbalanced PGM OUT (X) 1.7 V p-p MAX (1 kHz), 300 Z, Unbalanced (0 dBu = 0.775 V ) 1-3 (E) CA-755/755P...
Factory setting : ON S2 (MIC2) S2 (B-Y) Turning off disables MIC CH-2 signal output. Factory setting : ON Turning off disables B-Y signal to be added to video output signal. Factory setting : ON 1-5 (E) CA-755/755P...
Page 16
S2 (S2-2 to S2-4) invalid. Factory setting : OFF Selects wheather the INCOM control is exercised by the CA-755/755P or DVW-700 series camcorder. (S2-1 is not used.) Turns on/off the RET signal. Factory setting : ON ( ) in parentheses: Factory settings...
Page 17
INCOM and PGM and PGM LEVEL control adjusts a mixed ratio between them. Selects the signal output at the headphone. INCOM : INCOM signal : Mixed signal of INCOM and PGM : PGM signal Factory setting : MIX 1-7 (E) CA-755/755P...
To remove Outside Panel Loosen three screws. (Screws do not come off.) To remove Chucking plate Refer to Section 1-7 “Replacement of 40-pin Connector”. To remove Inside Panel Loosen three screws. (Screws do not come off.) 1-8 (E) CA-755/755P...
2. Slide portions A in the reverse direction to lock. B3 x 6 Chucking plate 2. Disconnect the four connectors shown in the figure and remove the chucking plate. Connector Chucking plate Conductive surface Connector Connector Connector 1-9 (E) CA-755/755P...
Page 20
5. Remove the screw securing the CN-1455 board. 6. Disconnect the two flexible card wires from the CN- 1455 board. Refer to Section 1-6 before disconnecting or connect- ing the flexible card wire. P2.6 x 4 Flexible card wire LW2.6 CN-1176 CN-1455 1-10 (E) CA-755/755P...
1. Remove the right side panel. (Refer to Section 1-5.) 2. Disconnect the IF-607 board. AC.DC/DC convertor 5. Remove the two screws and remove the retainer. Retainer B3 x 4 IF-607 6. Install a new AC.DC/DC convertor in the reverse procedures of the removal. 1-11 (E) CA-755/755P...
B2.6 x 4 RX-37 2-5. RX-37 Board Adjustment MB-705 ————— AC.DC/DC Convertor ————— RX-37 3. Disconnect the five coaxial cables. black blue white BLUE BLACK gray 4. Install a new MPX filter in the reverse procedures of the removal. 1-12 (E) CA-755/755P...
7. Install a new board in the reverse procedures of the removal. B2.6 x 4 FL-234 Spring 4. Remove the four screws securing the TRIAX connec- tor and disconnect the connector. Press to unlock Connector B3 x 6 TRIAX connector B3 x 6 1-13 (E) CA-755/755P...
In replacing, ensure that the battery is installed with “+” and “_” poles connected to the correct terminals. An improper connection may cause an explosion or leakage of fluid. + terminal Lithium battery Breaker release button _ terminal Desolder 1-14 (E) CA-755/755P...
Make sure 2. Standardization of Parts that planes A are in absolute contact with the connected Some repair parts supplied by Sony differ from those portion of the camcorder. used for the unit. These are because of parts common- ality and improvement.
Extension board is separately available for check or panel are recommended replacement parts. They are adjustment of plug-in boards. subject to cracks with the lapse of time. Check sometimes Extension Board Sony P/N To Be Extended by visual, and replace as necessary. EX-454 *Note...
Page 27
Section 2 Electrical Alignment 2-1. Preparation Fixtures : . Extension board (EX-454) 2-1-1. Equipment Required Sony part number : A-6258-670-A Optional accessory for CA-755/755P Measuring Equipment : . Extension board (EX-534) . Digital voltmeter Sony part number : A-8277-639-A . Frequency counter Optional accessory for CCU-550/550P .
Page 28
2-4-13. INCOM LEVEL Volume Low Level Adjustment 2-4-14. INCOM LEVEL Volume High Level Adjustment 2-4-15. PGM LEVEL Volume Low Level Adjustment 2-4-16. PGM LEVEL Volume High Level Adjustment 2-5. RX-37 Board Adjustment 2-5-1. PLL Free Run Frequency Adjustment 2-5-2. Return Video Level Adjustment 2-2 (E) CA-755/755P...
Page 29
2. S1-2/IF-607 board → ON Adjustment point : 1RV3 (Y GAIN)/DA-117 board : A = 860 ± 10 mV 3. Connect the DC IN connector of the CA-755/755P to Specifications the AC-550/550CE using the cable. 4. OUTPUT/DCC switch (Camcoder) → BARS...
Page 30
Adjustment point : 1RV4 (R-Y GAIN)/DA-117 board Adjustment point : 1RV5 (B-Y GAIN)/DA-117 board : 700 ± 10 mV : 700 ± 10 mV Specifications Specifications Setting after adjustment : S1-2/IF-607 board → OFF RV1 RV2 DA-117 BOARD (A SIDE) 2-4 (E) CA-755/755P...
Page 31
To be extended : DA-117 board Equipment : Oscilloscope/Audio level meter Test point : TP48/DA-117 extension board Adjustment point : 1RV2 (MIC 2 GAIN)/ DA-117 board : 220 ± 5 mV p-p (_20.0 ± 0.2 dBu) Specifications 2-5 (E) CA-755/755P...
Page 32
Test point : TP5/MD-117 board nect the triaxial cable. : E1/MD-117 board 2. Connect the DC IN connector of the CA-755/755P to the AC-550/550CE using the cable. Adjustment point : 1RV3 (Y LEVEL)/MD-117 board 3. OUTPUT/DCC switch (Camcoder) → BARS : A_B = 0 ±...
Page 33
Adjustment procedure : Adjustment point : 1RV2 (R-Y LEVEL)/MD-117 board Adjust 1RV8 and 1RV11 alternately until the V SYNC Specifications : A : B = 3 : 4 portions are flat. (Tolerance of 1% or better) V rate 2-7 (E) CA-755/755P...
Page 34
Specifications : A : B = 3 : 4 (Tolerance of 1% or better) MD-117 board : Adjust 1RV5 and 1RV6 alternately Specifications so that the carrier is minimum. RV10 TP10 RV11 TP11 MD-117 BOARD (A SIDE) 2-8 (E) CA-755/755P...
Page 35
. S1/MD-117 board → ON . Disconnet the DC IN connector. . S2/MD-117 board → ON Connect the CA-755/755P to the CCU with the triaxial To be extended : MD-117 board cable and turn on the POWER switch of the CCU.
Page 36
1. Disconnect the cable from the DC IN connector on the CA-755/755P . Carefully adjust an adjusting core such as LV8. 2. Connect the CA-755/755P to the CCU using a triaxial cable. Turn on the POWER switch of the CCU. To be extended...
Page 37
2-4-4. H CONT Level Adjustment 2-4-3. Data Demoduration Circuit Adjustment 2-4-4. H CONT Level Adjustment Preparation : To be extended : TR-101 board . Connect the CA-755/755P to a completely-adjusted Equipment : Oscilloscope Test point : TP16/TR-101 board CCU. Adjustment point : 1LV6 (DATA DC)/TR-101 board : 3.75 ±...
Page 38
2-4-6. MIC 2 Level Adjustment Preparations : Preparations : . Connect the CA-755/755P to a completely-adjusted CCU. . Connect the CA-755/755P to a completely-adjusted CCU. . Supply an 1 kHz, 2.2 mV p-p (_60 dBu) sine wave from . Supply an 1 kHz, 2.2 mV p-p (_60 dBu) sine wave from...
Page 39
Pin 1 (Y), Pin 2 (X) and the low frequency oscillator to Pin 1 (Y), Pin 2 (X) and Pin 3 (G) of INCOM/PGM connector of the CA-755/ Pin 3 (G) of INCOM/PGM connector of the CA-755/ 755P.
Page 40
Pin 1 (Y), Pin 2 (X) and 3 (G) of INTERCOM connector on the CCU front panel. . Setting of the CCU switches Pin 3 (G) of INCOM/PGM connector of the CA-755/ 755P. (CCU-550 series) .
Page 41
2-4-12. PGM Demoduration Level Adjustment Preparations : Preparations : . Connect the CA-755/755P to a completely-adjusted CCU. . Connect the CA-755/755P to a completely-adjusted CCU. . Supply an 1 kHz, 2.2 V p-p (0 dBu) sine wave from the . Supply an 1 kHz, 2.2 V p-p (0 dBu) sine wave from the...
Page 42
2-4-14. INCOM LEVEL Volume High Level Adjustment Adjustment Preparations : Preparations : . Connect the CA-755/755P to a completely-adjusted CCU. . Connect the CA-755/755P to a completely-adjusted CCU. . INCOM LEVEL control (CA-755/755P) → . INCOM LEVEL control (CA-755/755P) → Fully clockwise Fully counterclockwise...
Page 43
2-4-16. PGM LEVEL Volume High Level Adjustment Adjustment Preparations : Preparations : . Connect the CA-755/755P to a completely-adjusted CCU. . Connect the CA-755/755P to a completely-adjusted CCU. . PGM LEVEL control (CA-755/755P) → . PGM LEVEL control (CA-755/755P) → Fully clockwise Fully counterclockwise...
Page 44
2. Set the test signal generator as follows. Test signal generator . 5-STEP or 3-STEP Test point : RET OUT connector . LINEALITY (CA-755/755P) . APL 50 % Adjustment point : 1RV1 (VIDEO LEVEL)/ . STD RX-37 board : 1.00 ± 0.05 V p-p (75Z) .
7-627-556-38 s SCREW +P 2.6X4.0 7-627-556-77 s SCREW,PRECISION +P2.6X6 TYPE 1 3-564-029-00 s SPRING, COMPRESSION 7-682-547-04 s SCREW +B 3X6 3-686-349-01 o SHAFT,GUIDE 7-682-547-09 s SCREW +B 3X6 3-686-350-01 o SHUE(3) 7-682-560-09 s SCREW +B 4X6 3-686-366-01 o CONNECTOR BRACKET 3-686-367-01 s SCREW,STEP CA-755/755P...
3-606-106-01 o PLATE, GROUND 1-956-823-12 s HARNESS (CB) 3-175-715-02 s SCREW, FITTING, ADAPTOR 7-621-592-00 s SCREW +K 2.6X6 3-175-715-22 s SCREW, FITTING, ADAPTOR 7-621-731-08 s SET-SCT,HEX. 2X2.5,FLAT POINT 7-621-772-18 s SCREW +B 7-621-773-86 s SCREW +B 2.6X4 7-627-556-38 s SCREW +P 2.6X4 CA-755/755P...
1-954-672-11 o HARNESS (TRIAX(EK)) [for CE] 7-621-773-86 s SCREW +B 2.6X4 2-128-245-11 o PLATE (XLR), PHONE 7-627-556-37 s SCREW,PRECISION +P2.6X4 TYPE 1 7-682-545-04 s SCREW +B 3X4 7-682-546-09 s SCREW +B 3X5 7-682-547-09 s SCREW +B 3X6 7-682-560-09 s SCREW +B 4X6 CA-755/755P...
1-216-295-91 s RESISTOR, CHIP 0 (1/10W) 1-216-295-91 s RESISTOR, CHIP 0 (1/10W) 1-216-295-91 s RESISTOR, CHIP 0 (1/10W) 1-216-295-91 s RESISTOR, CHIP 0 (1/10W) 1-216-295-91 s RESISTOR, CHIP 0 (1/10W) 1-216-295-91 s RESISTOR, CHIP 0 (1/10W) 1-216-295-91 s RESISTOR, CHIP 0 (1/10W) CA-755/755P...
Page 50
1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V IC21 8-759-050-92 s IC SN74HC164APW 1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V IC22 8-759-050-92 s IC SN74HC164APW 1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V IC23 8-759-079-49 s IC TC74VHC04FS(EL) 1-104-823-11 s CAPACITOR,CHIP TANTAL 47MF/16V IC24 8-752-360-44 s IC CXK1203AR CA-755/755P...
Page 51
1-208-806-11 s RESISTOR,CHIP 10K 1/10W (2125) 1-216-684-91 s RESISTOR METAL FILM CHIP 24K R134 1-216-651-11 s RESISTOR,CHIP 1K 1/10W(2125) 1-216-684-91 s RESISTOR METAL FILM CHIP 24K R135 1-216-641-11 s RESISTOR,CHIP 390 1/10W(2125) R138 1-208-814-11 s RESISTOR,CHIP 22K 1/10W (2125) CA-755/755P...
Page 52
1-216-295-91 s RESISTOR, CHIP 0 (1/10W) 1-237-033-11 s RESISTOR,ADJ,CERMET 1K 1-237-033-11 s RESISTOR,ADJ,CERMET 1K 1-237-036-11 s RESISTOR, ADJ,CERMET 10K 1-237-036-11 s RESISTOR, ADJ,CERMET 10K 1-237-036-11 s RESISTOR, ADJ,CERMET 10K 1-237-033-11 s RESISTOR,ADJ,CERMET 1K 1-572-272-11 s SWITCH,SLIDE (1-1-2) 1-572-272-11 s SWITCH,SLIDE (1-1-2) CA-755/755P...
Page 53
1-163-237-11 s CAPACITOR CERAMIC 27PF/50V 1-239-895-11 s FILTER, EMI (SMD) 1-239-895-11 s FILTER, EMI (SMD) 1-163-237-11 s CAPACITOR CERAMIC 27PF/50V 1-239-895-11 s FILTER, EMI (SMD) 1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V EF10 1-239-895-11 s FILTER, EMI (SMD) 1-163-237-11 s CAPACITOR CERAMIC 27PF/50V CA-755/755P...
Page 54
8-759-058-55 s IC TC7S02FU (TE85L) 1-216-651-11 s RESISTOR,CHIP 1K 1/10W(2125) IC36 8-759-058-58 s IC TC7S04FU-TE85R 1-216-651-11 s RESISTOR,CHIP 1K 1/10W(2125) IC37 8-759-277-99 s IC CXD8889R 1-208-806-11 s RESISTOR,CHIP 10K 1/10W (2125) IC38 8-759-082-61 s IC TC4W53FU 1-208-822-11 s RESISTOR,CHIP 47K 1/10W (2125) 3-10 CA-755/755P...
Page 55
1-208-814-11 s RESISTOR,CHIP 22K 1/10W (2125) R130 1-218-760-11 s RESISTOR, METAL FILM CHIP 220K 1-216-699-11 s RESISTOR,CHIP 100K 1/10W(2125) R131 1-216-627-11 s RESISTOR,CHIP 100 1/10W(2125) 1-208-814-11 s RESISTOR,CHIP 22K 1/10W (2125) R132 1-208-822-11 s RESISTOR,CHIP 47K 1/10W (2125) 3-11 CA-755/755P...
Page 56
1-216-295-91 s RESISTOR, CHIP 0 (1/10W) TP12 1-535-877-22 o CHIP,CHECKER (TEST POINT) 1-216-295-91 s RESISTOR, CHIP 0 (1/10W) 1-216-295-91 s RESISTOR, CHIP 0 (1/10W) 1-760-273-11 s VIBRATOR, CRYSTAL 1-760-435-11 s VIBRATOR, CRYSTAL 1-567-866-11 s VIBRATOR,CRYSTAL 1-567-867-11 s VIBRATOR,CRYSTAL 1-567-812-11 s OSCILLATOR,CERAMIC 3-12 CA-755/755P...
Page 57
C114 1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V 1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V C115 1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V 1-104-852-11 s CAPACITOR,TANTALUM 22MF/10V C116 1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V 1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V C117 1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V 3-13 CA-755/755P...
Page 58
1-535-877-22 o CHIP,CHECKER (TEST POINT) 8-729-122-63 s TRANSISTOR 2SA1226-E4 1-535-877-22 o CHIP,CHECKER (TEST POINT) 8-729-122-63 s TRANSISTOR 2SA1226-E4 8-729-120-28 s TRANSISTOR 2SC1623-L5L6 1-239-950-11 s FILTER, LOW PASS (VIDEO) 8-729-216-22 s TRANSISTOR 2SA1162-G 1-239-951-11 s FILTER, LOW PASS (VIDEO) 8-729-122-63 s TRANSISTOR 2SA1226-E4 3-14 CA-755/755P...
Page 59
1-208-814-11 s RESISTOR,CHIP 22K 1/10W (2125) 1-216-651-11 s RESISTOR,CHIP 1K 1/10W(2125) 1-216-655-11 s RESISTOR,CHIP 1.5K 1/10W(2125) 1-216-627-11 s RESISTOR,CHIP 100 1/10W(2125) 1-216-655-11 s RESISTOR,CHIP 1.5K 1/10W(2125) 1-216-651-11 s RESISTOR,CHIP 1K 1/10W(2125) 1-216-651-11 s RESISTOR,CHIP 1K 1/10W(2125) 1-216-655-11 s RESISTOR,CHIP 1.5K 1/10W(2125) 3-15 CA-755/755P...
Page 60
R157 1-216-687-11 s RESISTOR,METAL FILM CHIP 33K R218 1-216-667-11 s RESISTOR,CHIP 4.7K 1/10W(2125) R158 1-216-651-11 s RESISTOR,CHIP 1K 1/10W(2125) R219 1-216-667-11 s RESISTOR,CHIP 4.7K 1/10W(2125) R159 1-216-651-11 s RESISTOR,CHIP 1K 1/10W(2125) R220 1-208-814-11 s RESISTOR,CHIP 22K 1/10W (2125) 3-16 CA-755/755P...
Page 61
1-104-914-11 s CAPACITOR CHIP TANTAL 22MF/16V 1-569-170-11 s CONNECTOR,COAXIAL(SMALL TYPE) 1-695-442-21 o PIN,CONNECTOR (PC BOARD) 10P 8-719-002-81 s DIODE 1T363 (VARI-CAP) 8-719-002-81 s DIODE 1T363 (VARI-CAP) 8-719-002-81 s DIODE 1T363 (VARI-CAP) 8-719-002-81 s DIODE 1T363 (VARI-CAP) 8-719-820-41 s DIODE 1SS302 3-17 CA-755/755P...
Page 62
1-216-295-00 s RESISTOR, CHIP 0 1/10W(2125) 1-218-700-11 s RESISTOR,CHIP 2.2K 1/16W(1608) 1-237-032-11 s RESISTOR,ADJ,CERMET 500 1-218-688-11 s RESISTOR,CHIP 680 1/16W(1608) 1-218-867-11 s RESISTOR,CHIP 6.8K 1/16W(1608) 1-417-171-11 s COIL, BALUNE 1-218-714-11 s RESISTOR,CHIP 8.2K 1/16W(1608) 1-417-171-11 s COIL, BALUNE 3-18 CA-755/755P...
Page 63
CN122 1-691-741-21 o PIN, CONNECTOR (PC BOARD) 2P 1-535-877-22 o CHIP,CHECKER (TEST POINT) 1-410-369-11 s CHIP INDUCTOR 1.0UH (3225) 1-410-369-11 s CHIP INDUCTOR 1.0UH (3225) 1-571-187-11 s SWITCH,TACTIL 1-571-187-11 s SWITCH,TACTIL 1-571-187-11 s SWITCH,TACTIL VDR1 1-810-605-21 s VARISTOR 3-19 CA-755/755P...
Page 64
1-163-021-91 s CAPASITOR, CERAMIC 0.01MF/50V 1-163-131-00 s CAPACITOR,CHIP CERAMIC 390PF 1-135-210-11 s CAPACITOR TANTAL 4.7MF/10V 1-163-259-91 s CAPACITOR,CHIP CERAMIC 220PF 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V 1-135-177-21 s CAPACITOR TANTALUM 1MF/25V 1-104-851-11 s CAPACITOR,TANTALUM 10MF/10V 1-163-113-00 s CAPACITOR,CHIP CERAMIC 68PF/50 3-20 CA-755/755P...
Page 65
1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V C129 1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V C191 1-135-210-11 s CAPACITOR TANTAL 4.7MF/10V C130 1-113-991-11 s CAPACITOR TANTALUM 33MF/16V C192 1-135-210-11 s CAPACITOR TANTAL 4.7MF/10V C131 1-128-397-21 s CAPACITOR, ELECT 100MF C193 1-135-210-11 s CAPACITOR TANTAL 4.7MF/10V 3-21 CA-755/755P...
Page 66
IC29 8-759-906-53 s IC TL062CPS 8-719-041-39 s DIODE KV1470 (5MA) IC30 8-759-075-70 s IC TA75S393F 8-719-800-76 s DIODE 1SS226 IC31 8-759-700-50 s IC NJM386M 8-719-800-76 s DIODE 1SS226 8-719-041-39 s DIODE KV1470 (5MA) IC32 8-759-906-53 s IC TL062CPS 3-22 CA-755/755P...
Page 67
1-216-689-11 s RESISTOR,CHIP 39K 1/10W(2125) 8-729-120-28 s TRANSISTOR 2SC1623-L5L6 8-729-200-87 s TRANSISTOR 2SC2714-Y 1-216-689-11 s RESISTOR,CHIP 39K 1/10W(2125) 8-729-200-87 s TRANSISTOR 2SC2714-Y 1-216-603-11 s RESISTOR,CHIP 10 1/10W(2125) 1-216-699-11 s RESISTOR,CHIP 100K 1/10W(2125) 8-729-122-63 s TRANSISTOR 2SA1226-E4 1-216-695-11 s RESISTOR,CHIP 68K 1/10W(2125) 3-23 CA-755/755P...
Page 68
1-208-806-11 s RESISTOR,CHIP 10K 1/10W (2125) R209 1-208-774-11 s RESISTOR,CHIP 470 1/10W (2125) R136 1-216-685-11 s RESISTOR,CHIP 27K 1/10W(2125) R210 1-216-659-11 s RESISTOR,CHIP 2.2K 1/10W(2125) R137 1-216-687-11 s RESISTOR,METAL FILM CHIP 33K R213 1-208-814-11 s RESISTOR,CHIP 22K 1/10W (2125) 3-24 CA-755/755P...
Page 69
1-237-038-11 s RESISTOR,ADJ,CERMET 50K R271 1-208-814-11 s RESISTOR,CHIP 22K 1/10W (2125) 1-237-035-11 s RESISTOR,ADJ,CERMET 5K R272 1-216-685-11 s RESISTOR,CHIP 27K 1/10W(2125) 1-237-038-11 s RESISTOR,ADJ,CERMET 50K R273 1-216-651-11 s RESISTOR,CHIP 1K 1/10W(2125) RV11 1-241-264-11 s RESISTOR ADJ 10K (CERMET) 3-25 CA-755/755P...
Page 70
1-535-877-22 o CHIP,CHECKER (TEST POINT) TP12 1-535-877-22 o CHIP,CHECKER (TEST POINT) TP13 1-535-877-22 o CHIP,CHECKER (TEST POINT) TP14 1-535-877-22 o CHIP,CHECKER (TEST POINT) TP15 1-535-877-22 o CHIP,CHECKER (TEST POINT) TP16 1-535-877-22 o CHIP,CHECKER (TEST POINT) 1-760-622-21 s VIBRATOR, CRYSTAL 3-26 CA-755/755P...
Page 71
1-565-801-11 s CONNECTOR, DOUBLE COAXIAL (For UC) 1-573-176-11 o CONTACT, FEMALE AWG22-26 CN111F(TO FL-234 BOARD) 1-580-585-11 o HOUSING, 18P 1-562-210-11 o CONTACT, FEMALE AWG18-22 CN23F(TO MB-705 BOARD) 1-562-211-11 o HOUSING, 3P 1-573-176-11 o CONTACT, FEMALE AWG22-26 1-580-581-11 o HOUSING, 10P 3-27 CA-755/755P...
Page 78
CXD1132Q (SONY) FLAT PACKAGE C-MOS TIME CODE GENERATOR / READER -TOP VIEW- SIGNAL DESCRIPTION BA0-BA2 B ADDRESS INPUTS B CHIP ENABLE INPUT ( "L" : ENABLE ) B DATA I/O BD0-BD7 B READ INPUT ( "L" : READ ) B BUSY OUTPUT BUSY B WRITE INPUT ( "L"...
Page 79
INTERNAL DATA BUS PC5/CI TIMER/EVENT PC6/CO0 3-10 COUNTER PC7/CO1 PORT B PB7-0 LATCH LATCH 28-35 AN7-0 INST. REG INST. 59-64 CONVERTER DECODER 1, 2 AREF PORT A PA7-0 A-GND (8/16) READ/WRITE SYSTEM STAND BY CONTROL CONTROL CONTROL MODE0 RESET STOP MODE1 CA-755/755P...
Page 84
– V + 3 V + 18 V CHANNEL TYPE A (X, Y, Z) CD4046BE LOW LEVEL HD14046BP HIGH LEVEL + 3 to + 8V MC14046BCP OPEN DON'T CARE MC14046BF TC4046BP CD74HC4046AM + 2 to + 6V MC74HC4046AF MC74HC4046AN 4-12 CA-755/755P...
Page 85
= +3 V to +12 V < NOTE: CONTROL INPUTS TYPE SELECT ON CHANNEL +2 to +5.5V 74AC/74VHC/74VHCT 74ACT/74HCT +4.5 to +5.5V 74LCX +2 to +3.6V OTHER TYPE +2 to +6V LOW LEVEL HIGH LEVEL OPEN DON'T CARE 4-13 CA-755/755P...
Page 87
+2 to +6V OTHERS INPUTS OUTPUTS SN75158PS (TI) SN75158PS-E05 LOW LEVEL DUAL DIFFERENTIAL LINE DRIVE HIGH LEVEL — TOP VIEW — NOTE: DON'T CARE TYPE AC/VHC +2 to +5.5 V (+5 V) +2 to +6 V +5 V 4-15 CA-755/755P...
Page 88
TC4S66F(TE85R) C-MOS BILATERAL ANALOG SWITCH —TOP VIEW— (SCALE 6/1) CONT F DET (+3 V to +18 V) IN/OUT OUT/IN GND 3 METER MUTE IF AMP DRIVE DRIVE STATION CONT SWITCH AF AMP PEAK DET LOW LEVEL HIGH LEVEL 4-16 CA-755/755P...
Page 89
4 17 5 16 6 15 7 14 8 13 ABT/ACT/BCT/HCT/VHCT OTHER TYPES +2 to +6V NOTE; TYPE 74HC +2 to +6V 74AC/74VHC +2 to +5.5V 74ACT/74FCT/74HCT +4.5 to +5.5V +2 to 3.6V 74LCX +2.7 to 3.6V 74LVC 4-17 CA-755/755P...
Page 90
(+2 to +6 V) Y = A 0; LOW LEVEL 1; HIGH LEVEL UPA101G (NEC)FLAT PACKAGE UPA101G-E1 TRANSISTOR ARRAY —TOP VIEW— TL064CPW (TI)FLAT PACKAGE TL064CPW-E05 OPERATIONAL AMPLIFIER (J FET INPUT) —TOP VIEW— – – (+18V) (-18V) – – 4-18 CA-755/755P...
Page 91
; OVER VOLTAGE LATCH OUTPUT ; FEED BACK2 ; REFERENCE VOLTAGE OVER ON/OFF REFERENCE VOLTAGE ON/OFF CONT REF OUT CONTROL REGULATOR LATCH T IN OSCILLATOR T IN – OUTPUT – – COMPARATOR – I IN N IN ERROR OVER CURRENT LATCH 4-19 CA-755/755P...
Page 125
CN-1455 CN-1455 CA-755 (UC) CA-755 (J) CA-755P (CE) CN144 FL12 SYNC OUT DA,1-16 FL13 IN OUT 512FS OUT DA,1-25 FL14 IN OUT 64FS OUT DA,1-24 FL15 IN OUT AUDIO 1/2 OUT DA,1-20 IN OUT FS(X) OUT DA,1-23 AUDIO 3/4 OUT...
Page 129
AU IN-OUT 4MHz MB,CN6 Y OUT 18MHz MB,CN5 C OUT 36MHz RX,CN1 RET VIDEO IN 70MHz RET IN MPX FILTER IN-OUT RET VIDEO OUT(X) RET VIDEO OUT(G) +7.5V +7.5V Frame Wiring RX-37 BOARD CN-1176 FL-234 SW-900/901 VR-236 B-¥CA755-FRAME 7-19 7-19 CA-755/755P...
Page 131
The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any...